Question about 1994 Chevrolet S-10 Blazer

1 Answer

Are 1994 s10 upper and lower ball joints pressed in

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 401 Answers

The upper ball joints are rivited or bolted if yhey have been replaced before
the lower ball joints on a 2WD are pressed in
the lower ball joints on a 4X4 are rivited or bolted

Posted on Jun 04, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to remove upper ball joint on driver side of an 1994 GMC Sonoma


The OEM ball joint is riveted into the upper control arm. There are two possible ways to replace the joint. You can purchase the entire upper control arm/ball joint assembly, which comes complete with the upper control arm bushings. This part costs about $150.00. You will also have to deal with the coil spring when replacing it this way. You can also buy just the ball joint for about $30.00. This will require that you drill out the rivets of the original ball joint and then bolt in the replacement with the bolts that are provided with it. The 2WD and 4WD versions are the same. See this link.


http://www.autozone.com/suspension-steering-tire-and-wheel/ball-joint-upper/gmc/sonoma-4wd/1994/6-cylinders-z-4-3l-tbi

Mar 18, 2015 | 1994 GMC Sonoma

1 Answer

How to remove upper and lower ball joins on a 4x4 bronco full size 1986


For Lower & Upper Ball Joint Step by Step :

For That you use a C-clamp style ball joint press to remove the ball joint from the suspension arm-note the location of the receiver cup ! For installation of the ball-joint, use the same tool when pressing the ball joint into the suspension arm-again, note the location of the receiver cup.

Step by Step :

  1. Raise and support the vehicle safely, with jackstands.
  2. Remove the spindle and the ball joint assembly from the vehicle.
  3. Remove the snapring from the ball joint. Using a ball joint removal tool, remove the ball joint from the spindle. Do not heat the ball joint or the axle to aid in removal.
  4. Installation is the reverse of the removal procedure. Torque the ball joint stud nut to 85-110 ft. lbs. for 1983-89 Ranger and Bronco II.

    Please Rate, Thank you !

Aug 13, 2010 | 1994 Ford Bronco

1 Answer

How to replace upper/lower ball joints on a 94 chevy suburban


YOU NEED SOME TOOLS LIKE 1/8 1/2 DRILL BITS.YOU NEED A PUNCH.YOU NEED A BALL JOINT SEPERATOR.YOU NEED BALL JOINT PRESS TOOL TO PRESS OUT BALL JOINT AND PRESS IN NEW BALL JOINT.YOU WILL NEED A HAYNES REPAIR MANUAL TO SHOW YOU PHOTOS AND GIVE YOU YOUR TORQUE SPECS.

Jul 21, 2010 | 1994 Chevrolet Suburban

1 Answer

How do you put in a ball joint in a 2001 sebring convertible


It depends on exactly which ball joint of the 3 per side your changing, but here are the details.

COMPRESSION LOWER ARM & LATERAL LOWER ARM ASSEMBLIES
Removal
1. Loosen compression lower arm ball joint nut. Using steering linkage puller, separate ball joint and
knuckle. Remove nut, bolts and compression lower arm assembly. Remove dust cover.
2. Remove stay. Remove shock absorber lower mounting bolt. Loosen lateral lower arm ball
joint and knuckle nut. Using steering linkage puller, separate ball joint and knuckle. Remove nut, bolt and
lateral lower arm assembly. Remove dust cover.
Inspection
Using preload socket, ensure breakaway torque for compression lower arm ball joint is 4-22 INCH lbs. (0.5-2.5
N.m) for 2000 models. On 2001 models, breakaway torque is 22-54 INCH lbs. (2.5-6.1 N.m). Ensure
breakaway torque for compression lateral lower arm ball joint is 13 INCH lbs. (1.5 N.m). Check compression
lower arm, lateral lower arm, dust covers, and bushings for damage and wear.
Installation
To install, reverse removal procedure. Use NEW ball joint nuts. Lubricate lip and inside of dust cover with
multipurpose lubricant. Using installer, install dust cover. Check front wheel alignment.
UPPER ARM ASSEMBLY
Removal
Using steering linkage puller, loosen upper arm ball joint and knuckle nut. Remove self-locking nut. Remove upper arm and upper arm shaft assembly. Remove dust cover.
Inspection
Using preload socket, ensure breakaway torque for upper arm ball joint is 3-13 INCH lbs. (0.3-1.5 N.m).
Replace upper arm assembly when measured value exceeds specification. Check upper arm, dust cover, and
bushings for damage and wear.
Installation
1. To install, reverse removal procedure. Use NEW self-locking nuts. Lubricate lip and inside of dust cover
with multipurpose lubricant. Using Ball Joint Installer (MB990800), install dust cover.
2. Ensure upper arm shaft assembly is installed at indicated angle. Verify upper arm shaft
assembly installation. Check front wheel alignment.

Once you have the correct arm off and a replacement joint (if available, some are not serviceable and require the arm to be replaced) then you will need a press or a ball joint press to change the joint. Such as
http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=38335

http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=46389

http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=66958

or http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=46967

Mar 17, 2010 | 2002 Chrysler Sebring

1 Answer

Front end bushing and ball joint do you need to change upper and lower bushings at same time and how hard is to them


It's not required to change the upper and the lower at the same time. However it will save you time if you do them both as if one is going out the other will soon.
The actual job is not that difficult but you may need a pickle fork or a ball joint removal tool to disconnect the ball joints from the steering knuckle. You will also need a ball joint press to remove/install the ball joints. You may also need a strut spring compressor. You can rent these at an auto parts store.
Basically you have to do the following -loosen lug nuts -jack the vehicle up and place on jack stands -remove wheel -remove upper ball joint cotter pin and nut -remove lower ball joint cotter pin and nut -with pickle fork/ball joint removal tool remove both upper and lower ball joints from steering knuckle -disconnect tie rod end from knuckle (optional depending on clearance) -disconnect strut (be sure to install strut spring compressors) -with ball joint press you will need to press both ball joints out (you also use the press to install ball joints)
Installation is reverse of removal.
For exact instructions you can buy the manual for about $20 or go to autozone.com, register, and view the manual on their site for free.

Jan 26, 2010 | 1999 Chevrolet S-10 Pickup

1 Answer

How do i change the upper and lower ball joints on


The upper and lower ball joints are riveted in on the oem ball joints you have to cut the rivets and then use a balljoint press to press them out the new ball joints have nuts and bolts just press them back in and tighten down the nut

Jan 20, 2010 | 2000 Dodge Ram 1500 Truck

1 Answer

How do i change upper and lower ball joints on a 2002 explorer sport


the lower ball joints have to be pressed into the lower control arms.The upper ball joints are part of the upper control arm so the upper control arms have to be replaced

Jun 24, 2009 | 2002 Ford Explorer Sport

2 Answers

Upper and lower ball joint


The ball joints are pressed into the steering knuckles. To remove them requires use of a ball joint press. If you don't have one you can usually rent one from a major auto parts retailer. You'll have to remove the brake calipers, rotors and backing plates. Disconnect the tie rod ends, and remove the upper pinch bolt. The lower joint has a nut that holds it to the axle that must be removed as well. Use a ball joint separator or "pickle fork" tool to separate the lower joint from the axle. Once you have the steering knuckle in hand, remove the snap ring from the bottom of the lower joint. Use the press to push the lower joint out then do the upper. replace the upper joint first using the press then do the lower joint in a similar fashion. Installation is naturally the reverse of removal. One thing to note is that the upper ball joint is located in the axle with a bushing. This bushing is where caster and camber adjustments are made. the factory presets these measurements using a bushing with a tab on it that locates it only one way in the axle. If the vehicle has ever been aligned and caster and camber adjustments were performed, the factory bushing will have been replaced with an aftermarket bushing. These bushings are rotatable and care must be taken to note where they were indexed in the axle. You should probably still get the alignment checked though, as suspension parts will tend to settle, and steering angles will change. Hope this helps.

Sep 01, 2008 | 2004 Ford E250

Not finding what you are looking for?
1994 Chevrolet S-10 Blazer Logo

447 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...