Question about 2001 GMC Yukon XL

2 Answers

I cannot get the bolts loose that hold the caliper on.

It is a 2004 GMC Yukon XL. Just looking for a trick or something that I do not see that keep them from turn in the caliper somewhere.

Posted by on

  • duane wine May 11, 2010

    not to clear what you are asking

  • gernlbithead May 11, 2010

    More input It says you cannot get the bolts loose but then you do not see that keep them from turn.....???

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 4 Answers

Try an open-ended wrench (on my 2001 Yukon XL on the rear, it was a 5/8") that is just inside the bolt head (bolt retainer) on the caliper -both top and bottom bolt. If you have that same config, the bolt retainer is just spinning when you are turning the bolt head. The wrench will allow you to put leverage on the retainer, and the bolt will come out quickly, as it is a short bolt.

Posted on Jun 23, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 266 Answers

If the bolts keep turning and the caliper is not being released theres something else wrong

Posted on Jun 20, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Instuctions on how to remove and replace hub bearings on 2002 yukon xl


Remove the tire. Remove the caliper and caliper bracket and hang aside. Remove the rotor. Remove the axle nut. Unplug the harness and remove it from the plastic holders. Turn the knuckle as necessary to remove the bolts securing the hub to the knuckle. Pushing on the axle outter joint will ease the process of removing the bolts. You may or may not have to hammer on the bearing to remove it from the knuckle. To install it reverse the procedure.

Jun 19, 2012 | 2003 GMC Yukon XL

1 Answer

How do i change out the battery on my 2007 denali. what is keeping it locked into position


there is usually a small bolt that holds it in place with a rubber block the rubs along the bottom of the battery. Take a flash light and look for the small bolt at the base of the battery,,You need like a 1/4" drive socket with a 6-9" extention on the socket to reach it..Just unscrew the bolt and the bolt and the block will come loose,you just lift it up and out of the way. Remove old battery and reinstall new one in reverse order.

May 21, 2011 | 2007 GMC Yukon XL Denali

1 Answer

Hi, I have a 2002 Yucon Xl and the parking brake pad needs to be replaced. Is the two callaper pins the only thing holding the brake assembly on the disc brake. If so do they come completely out of the...


Yes thats all that holds the caliper on and you can pull them all the way out, but if the bracket that holds the caliper wraps around the front then you will have to remove it also. two bolts.

Feb 13, 2011 | 2002 GMC Yukon XL

2 Answers

On 2001 gmc yukon rear disc brakes after u loosn the bolts on the caliper do they come all the way out and do u have to remove the bracket that holds the caliper on


It should pull off, you may have to get a big "C" clamp and push the caliper piston back, or sometimes you can pry the piston back with a bar or screwdriver, be careful what you pry on.

Jan 05, 2010 | 2001 GMC Yukon XL

2 Answers

2004 Yukon XL Denali fuel gauge fluctuations


Your sending unit for the guage is part of your fuel pump in the tank. But first try your fuel pump relay, may be working intermittenly when you hit a bump or something. Or possibly a loose wire somewhere along the way. Much less expensive (worth a look).

Dec 18, 2009 | 2004 GMC Yukon

1 Answer

I cant get the rear brake caliper off of my 2001 yukon . The bolts holding it on just turn without moving in or out . How do I change the brakes ?


If you will look at the inner part of the caliper that the bolts go into they have a flat side for a wrench to go on. Put a wrench on these flat spots and then remove the bolts. Good Luck

May 16, 2009 | 2001 GMC Yukon XL

2 Answers

Replace rear brake pads on 2001 yukon xl


First remove the cap off the master cylinder. Push in the piston on one caliper with a c clamp, or pry it back between the pad and rotor with a prybar. Then remove the 2 bolts on the caliper itself. Replace pads.Go to other side, repeat sequence

Dec 11, 2008 | 2001 GMC Yukon XL

2 Answers

Removing rear brake pads on gmc yukon xl 2000


take a pair of pliers and hold the inter side of the guide and turn the bolt. the bolts is only 8mm w x 25mm L. this will allow you to remove the calipers.

Nov 24, 2008 | 2000 GMC Yukon XL

Not finding what you are looking for?
2001 GMC Yukon XL Logo

Related Topics:

252 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...