Question about 1994 Ford F150 Styleside Supercab

1 Answer

1994 Ford F-150 4x4 transfer case won't shift out

My 4x4 won't come out of four wheel drive with the engine running and I also notice that sometimes the lite by the 4x4 light in the dash is on but it's not in 4x4 this is usually right after it is started any idea's?

Posted by on

  • msalow Jun 06, 2009

    I hear the relay clicking in the right side of the dash sometimes it goes in grar but when it does go into gear it won't come out unless you turn off the key switch and shut off the engine

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 106 Answers

Vacuum Leak by the auto/man hubs??? Just a starting point....... Does it sound like something is happening when you use the switch?

Posted on Jun 04, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 ford ranger - Where is the 4x4 actuator located


On the transfer case
Transfer Case - Electronic Shift
The four-wheel drive electronic shift-on-the-fly feature electrically shifts the vehicle transfer case between 2WD, 4WD HIGH, and 4WD LOW. The system mode is selected by the operator through the mode select switch (MSS) on the instrument panel. The operator is informed which mode the system is in by two instrument cluster indicators: one for 4WD HIGH which appears as 4WD, and one for 4WD LOW, which appears as 4WD LOW. Shifts into 4WD HIGH can be made at any speed. When shifting into 4WD HIGH with the vehicle stationary, tooth blockage may occur preventing shift completion. When the vehicle is driven above 8 km/h (5 mph) the shift will complete. When shifting in or out of 4WD LOW, the four-wheel drive (4WD) control module requires that the vehicle speed be less than 5 km/h (3 mph), the brake pedal be applied, and the transmission be in NEUTRAL (automatic transmission) or the clutch pedal be depressed (manual transmission).
The gearmotor encoder assembly is mounted externally on the transfer case. It drives a rotary cam which moves the mode fork and range fork within the transfer case between the 4WD HIGH, 4WD LOW, and 2WD range positions.
The four-wheel drive (4WD) control module controls the gearmotor encoder assembly that shifts between 4WD HIGH, 4WD LOW, and 2WD modes.

Mar 17, 2017 | Ford Cars & Trucks

1 Answer

4 wheel drive won't engage


Which do you have ?
Transfer Case - NVG 236 (Two Speed Automatic)
Transfer Case - NVG 233-NP1 (Two Speed Selectable)
The NV236 transfer case is an automatic transfer case with three drive ranges. Shifting from rear wheel drive to four wheel drive is done automatically when the transfer case shift control module receives wheel rotating slip information from the speed sensors. The transfer case shift control module then engages the transfer case motor/encoder to position the transfer case from rear to four wheel drive. When the transfer case shift control module receives information that the wheel rotation is the same on both axles, the transfer case shift control module sends position information to the motor/encoder to put the transfer case back into rear wheel drive. The three drive ranges are 2HI, 4HI, and 4LO. The 2HI position is for normal driving with the rear wheels pushing the vehicle. The 4HI, position is for driving through sand, snow, mud, gravel, or heavy rain at normal or slightly below normal speeds. The 4HI engages the front axle to allow for four wheel drive. The front axle is pulling the vehicle, and the rear axle is pushing the vehicle. The 4LO range is used for off road driving, heavy snow, deep mud, or shallow fording. The 4LO is similar to the 4HI except that the gearing in the transfer case is set for low speed and high torque. The NV236 is manufactured at Syracuse New York by New Venture Gear a division of New Process Gear for General Motors.
Is the switch light on or flashing ? If you have automatic 4x4 there are several DTC'S that can set >
DTC B2725 ATC Mode Switch Circuit Malfunction DTC C0300 Rear Speed Sensor Malfunction DTC C0305 Front Speed Sensor Malfunction DTC C0308 Motor A/B Circuit Low DTC C0309 Motor A/B Circuit High DTC C0310 Motor A/B Circuit Open DTC C0315 Motor Ground Circuit Open DTC C0323 T-Case Lock Circuit Low DTC C0324 T-Case Lock Circuit High DTC C0327 Encoder Circuit Malfunction DTC C0362 4LO Discrete Output Circuit High DTC C0367 Front Axle Control Circuit High DTC C0374 General System Malfunction DTC C0376 Front/Rear Shaft Speed Mismatch DTC C0387 Unable to Perform Shift DTC C0550 ECU Malfunction DTC C0611 VIN Information Error

Dec 01, 2015 | 2000 Chevrolet S-10

1 Answer

My truck is stuck in four wheel drive


At the risk of going to the offensive, sometimes it's the simplest thing - you ARE putting it in neutral, at a stop, engine running, with the brake pedal pressed, when trying to shift out of 4wd, yes?

2) Check for blown fuse for 4x4 shift module

3)This sounds dumm, but worked on my wife 99. I took it to a school parking lot, put it in reverse, floored it and pulled on the lever and it popped out of 4x4

4) The shift motor is bad. Replace it.

Hope this helps.

Feb 18, 2015 | 1999 Ford Expedition

2 Answers

Why does my transfer case pop out of gear when I am in four wheel drive?


Have you checked the engine and transmission mounts?? If these are loose they could easily shift causing the linkage to kick it into another gear.

Most of these I have seen were Electronically shifted, if that is the case you might have a sensor problem in the cab, or a wiring issue.

May 15, 2014 | 1996 Ford F250 Crew Cab

1 Answer

My 98 dodge ram won't go in to 4x4 where can I


i would start with the transfer case . check fluid level and also check your shift linkage to transfer case. also could have worn chain and gears. Is there any grinding noise when you try to shift into four wheel drive ?

Oct 23, 2012 | Cars & Trucks

1 Answer

2001 Dakota: four wheel drive will not engage and windshield wi...


4x4 issue could be either the TCCM Transfer Case Control Module, or the transfer case shift motor.

When you turn your dash switch from 2wd to 4HI, can you hear the shift motor underneath operating?

May 17, 2010 | 2001 Dodge Dakota

1 Answer

1994 nissan pathfinder- when I push in the clutch it will let me shift through the gear but does do anything - when I depress the interlock put in 1st gear it jumps into four wheel drive - tranny and...


ipresume your talking about a manual gearbox
and you have a seperate lever for four high and four low possibly 2 wheel drive on it as well trouble has to be in smalllever linkage and not engaging properly to solve it move the lever around different positions see do u get drive

Mar 06, 2010 | 1994 Nissan Pathfinder

2 Answers

I have a 2004 ford f-150 off road 5.4 liter. My


If this is a 2004 Heritage ( old body style ) and the transfer case is known to lock in ( check with truck jacked up, shift into 4WD and try to turn front drive shaft ), the next item to look at is the vacuum disconnect motor for the front axle. This is on the front axle, and will move when shifted into 4WD
3b8c336.jpg


It is item #10, on this parts diagram
b48b167.gif
If you do not have movement in this, check the vacuum lines with a vacuum pressure gauge, to see if vacuum is being applied ( Pink line is 2WD w/ vacuum is operation, Blue line is 4WD w/ vacuum operation ). If no vacuum at the lines, check them back to the vacuum shift solenoids
b684463.jpg
4ef54b0.jpg

Jan 04, 2010 | 2000 Ford F150 Flareside SuperCab

4 Answers

2001 Chevy Blazer 4 wheel drive


The four wheel drive systems in these vehicles are simple. The push button controls the four wheel drive computer. The computer tells the encoder motor (on transfer case) to shift. When the transfer case shifts there is a vaccum switch on the transfer that is activated which sends vaccum to the accuator under the battery. The accuator pulls a cable to lock the front axle in. This covers all s series trucks and suv's with push button four wheel drive but not with auto or all wheel. Now to answer some questions. If your push button is lit up but will not go in to four high you should try to reset the four wheel drive computer. To reset pull the courtesy light and atc fuses for sixty seconds install fuses then cycle key on and off 5 times. If your transfer case shifts but your front end does not lock in check for vaccum at the switch on the transfer case in and out. If no vaccum out replace switch motormite number 49315 at parts store. If you have vaccum out check accuator.

Jun 02, 2008 | 2001 Chevrolet Blazer

Not finding what you are looking for?
1994 Ford F150 Styleside Supercab Logo

321 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...