Question about 1996 Honda Accord

1 Answer

Bleeding Clutch Cylinder with no bleeder screw

Replaced the external clutch slave and master cylinder, how do you bleed it with NO bleeder screw. I have a 1995 Dodge Dakota

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,187 Answers

I have not tried myself but see if the link below will work for your case. It is not the same model as you have but most vehicles have the same components for the non electronic parts. http://www.2carpros.com/forum/1988-dodge-dakota--bleding-air-out-of-clutch-master-cylinder-vt248517.html

Posted on Jun 04, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Why does clutch leak off and wont go into gear 96 toyota tacoma when you push on clutch pedal goes to the floor it wont engage clutch to be able to put into gear


the most likely reason is either the clutch master cyl. needs to be replaced.or the.slave cyl. its mounted down on the transmation under the hood find the resivore for the clutch. check the fluid level.if its low , fill it back up , and look for signs of a leak
you will probally have to bleed out all of the air from the system.its done almost the same way as bleeding the brakes. Good Luck.

Nov 05, 2011 | Cars & Trucks

2 Answers

My clutch doesn't always disengage when the peddle is on the floor and when starting out in first bolts ahead as though the clutch was already part way out. I took it to a shop and they said my clutch...


your clutch master cylinder is right beside your brake master cylinder. I would advise you to replace the master cylinder and the slave cylinder together. The slave cylinder is on the side of the transmission. The slave cylinder does have a bleeder screw on it after the parts are bolted in place fill with dot 3 brake fluid and open the bleeder on the slave cylinder until fluid starts dripping out. Then tighten bleeder then open bleeder and have someone push down on clutch pedal while the pedal is pushed down tighten the bleeder the release pedal. Repeat this procedure until you get no air and the pedal feels normal and you should be good to go. Good luck!

Apr 14, 2011 | 1991 Toyota Celica

3 Answers

I replaced a slave cylinder on my 2000 Ford F250 diesel truck now I can't get the air to bleed off. A mechanic friend said to keep pumping the clutch but that doesn't help


Hi, if you didn't bench-bleed the slave, it can have trapped air away from the bleeder. What I do is to bleed the slave by pushing the cylinder in with the bleeder open (close the bleeder before releasing the piston). Depending on the type of slave, you can usually get a screwdriver between the clutch lever and the piston to compress it. You need to compress it fully to get the bubbles out of the bleeder port. OK?

jturcotte_980.gif

Feb 06, 2011 | 2000 Ford F250 Super Duty Crew Cabs

2 Answers

My 1996 Chevrolet K3500 Dually has a hydraulic clutch, how do I change the fluid and bleed it.


FIRST REMOVE ALL OLD FLUID FROM CLUTCH MASTER CYLINDER YOU CAN USE A SIPHON YOU HAND PUMP.AUTO PARTS STORES SELLS THE HAND PUMP SIPHONS. THEY DONT COST MUCH AND KEEP FROM MAKING A MESS.SIPHON OUT MUCH AS YOU CAN THE OLD FLUID IN THE CLUTCH MASTER CYLINDER.THEN POUR IN THE NEW FLUID DOT 3 BRAKE FLUID IN CLUTCH MASTER CYLINDER.OKAY YOU NEED A HELPER.LOCATE THE SLAVE CYLINDER.REMOVE SLAVE CYLINDER HOLD SLAVE CYLINDER 45 DEGREES WITH BLEEDER SCREW LOCATED AT THE HIGHEST POINT.HAVE A SMALL DRAIN PAN UNDER SLAVE CYLINDER.HAVE HELPER FULLY DEPRESS AND HOLD THE CLUTCH PEDAL THEN OPEN BLEED SCREW.CLOSE THE BLEED SCREW AND HAVE HELPER RELEASE THE CLUTCH PEDAL.REPEAT THIS PROCESS UNTIL ALL THE OLD BRAKE FLUID AND AIR BUBBLES LEAVES THE HYDRALIC SYSTEM AND WHEN YOU CAN SEE GOOD STREAM CLEAN FLUID NO BUBBLES YOU HAVE GOOD SOLID CLUTCH ALL IS GOOD.MAKE SURE THROUGH THE BLEEDING PROCESS YOU DONT LET CLUTCH MASTER CYLINDER RUN DRY OR YOU WILL HAVE TO START OVER.KEEP CLUTCH MASTER CYLINER FULL BRAKE FLUID WHILE DOING THE WHOLE BLEEDING AND FLUSHING PROCESS.

Jan 22, 2011 | 1996 Chevrolet C/K 3500

1 Answer

Clutch mastercilinder bleeding bmw 325tds how do you get brakefluid from reservoir to the slavecilinder. must it be pumped or will normal bleeding solve my problem


You can try regular bleeding by pumping pedal, also you can try a bleeding tool hooked to cylinder bleeder screw, and last a plastic bleeding siringe to push fluid through the bleeder screw into master, i would start with bleeding the master at the line first then go to the slave cylinder and if that doesnt work then try pushing fluid through bleeder screw into master.

Jul 19, 2010 | 1994 BMW 3 Series

2 Answers

Where is the bleed valve for clutch on a 1991 jeep wrangler


1. Fill master cylinder reservoir with DOT 3 brake fluid. Raise and support vehicle. Attach bleeder hose to bleeder screw on bleed line of slave cylinder. See Fig. 1 (attached in link) . Place other end of hose in glass container 1/2 full of brake fluid. Loosen bleeder screw while holding bleeder screw fitting.

2. Have an assistant depress clutch pedal to the floor. Tighten bleeder screw and release clutch pedal. Repeat bleeding procedure until fluid entering container is free of bubbles. DO NOT allow reservoir to run out of fluid during bleeding. Refill clutch master cylinder reservoir.

CAUTION: DO NOT allow bleed line to bend or flex when loosening
bleeder screw.

FIG1: http://anubiscycle.com/fixya/91wranglerslaveassy.png

Jan 14, 2010 | 1991 Jeep Wrangler

1 Answer

HYDRALIC CLUTCH BLEEDING 1993 CHEVY TRK 2500 ,AFTER REPLACING THE LINE


raise and support vechicle safely.remove slave cylinder.hold slave cylinder at a 45 degree angle.with bleeder screw at it highest point.have a helper fully depress hold clutch pedal.then open the bleeder screw. then close the bleeder screw.and have helper release the clutch pedal repeat the procedure until all of the air is evacuated from the system.keep check on on master cylinder keep fluid level full.to keep air from being drawn through the master cylinder.never release a depress clutch pedal with bleeder screw open.or air will enter the system.

Jul 19, 2009 | 1993 Chevrolet C2500

1 Answer

Im having difficulty in bleeding a cluch o a ford


clutch systems bleed just like brakes, if you have an external leak at the clutch master cylinder, then bleeding will be difficult, it should be replaced. I use a two person bleeding system, I fill the master, crack the bleeder screw open and have my 2nd push the clutch down and hold it, then I close the bleeder and tell my 2nd to release the pedal, repeat until no air is present.

Apr 08, 2009 | Ford Club Cars & Trucks

2 Answers

Bleeding the hydraulic clutch


Have somebody pump the pedal fast about 3 or 4 times, on the last pump hold pedal down and close bleeder. Make sure fluid stays full in master cylinder, try it again, if it still doesn't work, then you might have a bad slave valve, if you haven't already replaced it.

Jan 30, 2009 | 2001 Pontiac Firebird

2 Answers

Clutch bleeding


Try opening bleeder screw on slave cylinder and let it GRAVITY BLEED, just open clutch mater and fill with fluid and then open slave cylinder bleeder screw and let it gravity bleed( run out by itself) When it does close bleeder screw and you should get pressure.(make sure master doesn't run out of fluid during this preocess).If pedal not good enough bleed as usual. PUMP PEDAL ABOUT 6 time then hold down to the floor using wrench open slave bleed screw and close back up with pedal still being held DOWN. Repeat until fluid comes out with out air.However if all this doesn't work, YOU WILL NEED TO REPLACE CLUTCH MATER CYLINDER. Conatct if you need more help and Good Luck. Thanks for using FIX YA

Jan 12, 2009 | 2001 Honda Civic

Not finding what you are looking for?
1996 Honda Accord Logo

2,288 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...