Question about 2006 Ford F-250 Super Duty

1 Answer

How do i remove the stereo on my 2006 f250 pu

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 93 Answers

Removal and Installation

  1. Tilt the steering wheel downward.
  1. NOTE: Ignition switch must be in OFF position if disconnecting the passenger airbag deactivation (PAD) switch electrical connector. Otherwise, a diagnostic trouble code (DTC) will be set in the restraints control module (RCM) memory and must be erased before releasing the vehicle.
    Position the ignition switch in the OFF position.
  1. Remove the instrument panel cluster finish panel.
    • Pull outward on the instrument panel center finish panel, as indicated, to release the retaining clips.
    • Disconnect the electrical connectors.
    how do i remove the stereo on my 2006 f250 pu - n0080164.gif
  1. To install, reverse the removal procedure.
Audio Unit n0029180.gif
Item Part Number Description 1 — Audio unit screws (4 required) 2 18C869 Audio unit 3 — Audio unit electrical connector (part of 14401)
Removal and Installation
  1. Remove the instrument cluster finish panel. For additional information, refer to.
  1. Remove the 4 screws and the audio unit.
    • Disconnect the electrical connector and the antenna lead-in cable.
  1. To install, reverse the removal procedure.

Posted on Jun 04, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I need a fuse diagram for a 2006 Ford F250 2WD. My lights all work great on the PU but when I connect the trailer the lights work but no brake lights or turn signals.

If all the lights work properly with the trailer wiring not connected then the truck itself is fine. If attaching the trailer wiring causes the lights to permanently stop working on the truck then you are blowing a fuse and it will need to be replaced. Your owners manual will show you where the fuse panel is. You should be able to check the wiring plug at the back of the truck to be sure it is working properly with a test light and a helper. If the power for signals/brakes etc are not all working at the plug, then trace back and fix these. If all is good at the truck's plug, then the trailer wiring must be faulty. Again, go through it and fix anything that is broken or corroded. Of course it goes without saying, make sure all the bulbs are good.

Nov 02, 2014 | Cars & Trucks

1 Answer

I have 2006 f250 the stereo has an aux bottom how do i hook up an ipod

get a dual sided auxiliary cable and BOOM PAPERTOWEL, plug er up and press play

Sep 15, 2011 | 2006 Ford F-250 Super Duty

1 Answer

Was driving pu when it sputtered and stalled now when key is turned to start truck theres nothing at key no click from solonoid

I had a f250 with the exact problem you are having the ecm was bad , on my f250 it was located on the driver side fender well. Once i replaced it i was up and moving again. Hope this helps.

Mar 21, 2011 | 1986 Ford F150 SuperCab

1 Answer

What is location of turn signal flasher 2006 f250

The flasher on a 2007 F250 and F350 is located on the R side of the Kick panel on the drivers side (center of the dash). There is a black cover that is covering the flasher and will need to be removed. This can be acomplished w/o pulling the dash loose.

Jun 20, 2010 | 2006 Ford F-250 Super Duty

1 Answer

I just filled up my 2006 NISMO/Frontier PU. Gas

ground not making good connection to frame by gas tank sending unit ground

May 07, 2010 | 2006 Nissan Frontier

1 Answer

I need to replace the rear stereo speakers in my 2006 Corolla

You have to remove the package tray to access them. once it is removed they are held dow with 4 bolts per speaker

Apr 20, 2010 | 2006 Toyota Corolla

1 Answer


Yeah those stereos are a pain to get out with just 4 peices of wire clothes hanger. I think a part store sells or lends out the Ford stereo removal tool that works perfect everytime. Way better than a clothes hanger!

Feb 20, 2009 | 1996 Ford F250 Crew Cab

1 Answer

Stereo wiring

You might save yourself a lot of headaches by stopping by a car stereo sales/installation place, and ask for wiring adapter harness. They should have an adapter plug that goes from your factory plugs to the new stereo. $10-$20 well spent. You may even find what you need at an auto parts store that sells stereos too, or radio shack.

Jul 19, 2008 | 2004 Ford F250

Not finding what you are looking for?
2006 Ford F-250 Super Duty Logo

214 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

79077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

5677 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides