Question about 2006 Chevrolet Impala

1 Answer

2006 Chev Impala turn signals not working on rear lights, turn signal flashing at a faster rate than normal, No brake lights when pushing on brakes.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 6,784 Answers

Two issues here, you will need to replace the flasher. this will correct the erratic turn signals.

Concerning the brake light. Make sure the bulbs are in working condition and, check the wiring harness for faults as well. if the bulbs and wires arr OK, replace the brake light switch.

You can test for proper current by pulling the brake light bulbs out the socket and, use the copper prongs inside the brake light socket for testing. use a volt meter and, hit the brake pedal and, see if the meter registers a current. if not, replace the wiring harness.

Posted on Jun 04, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 ford f150 2wd turn signal/hazard lights and brake lights not working


Sometimes there are 2 flashers, one for the 4-way emergency and the other for turn signals.

Little confused about brake lights turning on/but not flashing. There is a switch on the brake pedal lever or on the clutch lever depending if it has a manual transmission. This switch often gets hit by the drivers feet and dislodged or broken. If it is broken it can do weird things by routing electric to wrong places. Since you have brake lights it is less likely to be bad but worth a look.

Turn signal stalk. Can break in so many ways. One thing to try is to push the 4-way flasher off and on about 20 times. The internal contacts for the flashers share the emergency function. Using the 4-way button can re-shift the contacts back to normal.

May 14, 2018 | Ford F-150 Cars & Trucks

1 Answer

Brake lights and turn signal lights


Hello, my name is Steve and the bulb for the left and right turn signal is 1157 . This has the 4-way flasher/turn signals and Brake light elements in the bulb.

if you are doing this yourself, make sure you look at the guide pins on the side of the base of the bulb and line them up with the corresponding guide. If you fail to do so, the turn sigal flash will be faster than usual. Take care on how you remove the bulbs.

I hope this will help you, Steve

Sep 03, 2015 | 1996 Lincoln Town Car

1 Answer

Left bleaker and break light not working. Turn signal works bleaks faster than right side.


Has the vehicle been in an accident on the left rear side. First check the bulb to be sure it is not defective, trade it out with the side that works properly to test. If the bulb works well then My thought are you may have a shorted wire. The turn signal flasher works by heat build up within the flasher the heat is caused by the load of the bulbs, the load heats the metal spring causing it to open the circuit then as quickly as it cools down the circuit closes again lighting the bulbs.
There is also a possibility of a defect in the turn signal mechanism on the steering column. The turn signal switch on many models does three different things on many models that use the same bulb element / or bulb for brake and turn on rear of vehicle. It controls the circuit for brake light by sending power both left and right side rear when turn signal is in neutral position then when turn signal is in left turn the switch cancels brake light power to left side rear and supplies flasher power to left side while maintaining brake light supply to the right side rear, and so on opposite when the right turn is chosen on turn signal switch. The turn signal indicators on the dash normally run off the same circuit as front turn signal bulb only which is also controlled by turn signal switch. Front has turn signals but no brake light.
I think there is an additional load on the left side rear turn circuit and it could be either a wire that is shorted or the turn signal switch if the same bulb element is used for both functions.
Often times if trailer lighting is connected the flasher will also blink a little faster because of the extra load of additional bulbs.

Feb 15, 2015 | Cars & Trucks

2 Answers

Turn signal


because of no light flasher on left side the front one will go faster .maybe the left rear light is burn. and brake lights are control by the brake switch on brake pedal hardware, might be unadjust

Sep 12, 2013 | 2001 Pontiac Grand Prix

3 Answers

1994 Chevy C1500 truck. No rear brake lights


Most likely this is a brake light switch issue. Replace switch.

If your emergency flashers don't work, all flasher bulbs are fine, but flashing too fast, then check and replace Hazard light switch.

Oct 29, 2012 | 1994 Chevrolet C1500

2 Answers

2007 chevy impala brake light and left turn signal not working


Fast flashing dash signals mean there is a bulb issue-DEFINATELY!

Aug 07, 2012 | 2007 Chevrolet Impala LS Sedan New Cars

1 Answer

I have a 2002 pontiac aztek. My rear right signal/brake lamp does not work. When i signal left, the front and rear left lights flash normally. When i signal right, the front right light flashes normally...


as for the faster flashing thats as simple as a blown bulb, replace the bulb and see if that fixes the problem, it may fix the lot because the other symptoms you mention are a bad connection, if bulb is fine check the connection isnt loose or corroded over. if it is simply file it back to establish better connectivity,

Jun 22, 2010 | 2002 Pontiac Aztek

1 Answer

Jaguar xj6 break light cancels signal


Replace the turn signal switch. Bad contact inside causing a crossing of the circuits. When the turn signal is applied it should open the brake light circuit allowing for just the signal to work. Doesn't sound like the switch is doing it's job.

May 23, 2010 | 1989 Jaguar Vanden Plas

2 Answers

Left turn signal doesnt work and my brakelights


  1. Check the fuse make sure it is not busted and also use a designated amp only.
  2. Check the bulb and the wires also.

Mar 28, 2010 | 1997 Chevrolet Lumina

1 Answer

Chev Cavalier 2003 only one rear turn/brake/hazard light


I have a 2002 Chev Cavalier that had the same exact problem. I replaced the bulb harness (purchased from a chevy dealership for around $5) which was fairly easy to do. I have had zero problems with it since.

Sep 15, 2008 | 2001 Chevrolet Cavalier

Not finding what you are looking for?
2006 Chevrolet Impala Logo

641 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85160 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...