Question about 2004 Chevrolet Silverado
I can not find it
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Look under Driverside Dash under Steering wheet find the Plug for Scanner then go straight UP from there It Should Be Cliped to A Bracket DIRECTLY ABOVE THE DIAGNOSTIC LINK PLUG Its Ther Just Hunt for it sometimes People change them and DONT Put EM BACK
Posted on Jan 30, 2009
The turn and hazard flashers are integrated into one flasher on these models. The flasher is located in the hazard warning switch and the hazard warning switch is located on the trim plate. Replace the flasher by unplugging the old one, removing it from the panel, and plugging in the new one.
Remove the bezel from the ignition switch
Carefully remove the instrument panel accessory trim plate.
To remove the trim plate, use a suitable prytool to carefully apply pressure at the retaining clip points . . .
. . . then gently pull the accessory trim plate away
Detach the electrical connector from the hazard warning switch.
Unplug the electrical connector from the hazard warning switch . . .
Unfasten the screw securing the hazard warning switch and remove the switch.
. . . then unfasten the screw securing the hazard warning switch and remove the switch from the vehicle
Installation is the reverse of removal.
Posted on Dec 01, 2009
Testimonial: "just what I needed, thank you so much."
On the 1993 Sedan de Ville, The hazard flasher is easy to locate, under the dash between the steering column and the radio. Looking up, you will see the smooth round side of the flasher and the wires will be attached to the top.
The turn signal flasher is more difficult to get to, but readily accessed with a T-15 torx driver and a little patience. It is located to the left of the steering column, but is most easily accessed through the dash panel instead of from underneath.
1. remove the T-15 screw from above the headlight switch, above the fuel data center, and above the small panel similar to the one around headlight switch. All of these are somewhat hidden, and you'll need to feel for them or get low and look up at them.
2. Using a bent piece of wire or an allen wrench, or anything else handy, pull off the small trim piece that is directly below the steering column. On my car, this is wood-grained plastic. This will expose two more screws that need to be removed.
3. Now, you should be able to remove the large dash trim panel that goes around the fuel data center.
4. Unscrew the two T-15 screws that hold the fuel data center into the dash, and it should pull straight forward. There should be plenty of wire to move it out of the way.
5. The turn signal flasher is the silver can that you see to the right in the opening you just created by removing the fuel data center module. It has a single plug with two conductors on the back. I had to use a small screwdriver to pry it off.
It is a different part number, so I don't know if you can just swap it for the hazard flasher to test it like you can on many cars. I just replaced mine with a Wagner 323, which is what came out of mine.
Posted on Apr 30, 2010
Tips for a great answer:
Jun 12, 2015 | 2004 Chevrolet Blazer
Sep 08, 2014 | Cars & Trucks
Feb 11, 2014 | 1993 Chevrolet C/K 3500
Oct 02, 2013 | Cars & Trucks
Jul 06, 2013 | 2004 Chevrolet Chevrolet Malibu MAXX LT
Jun 11, 2011 | 2004 Chevrolet Impala
May 10, 2011 | 2004 Chevrolet Silverado
Jul 04, 2010 | 2000 Ford Expedition
Aug 19, 2009 | 1991 GMC C3500
455 people viewed this question
Usually answered in minutes!