Question about 1993 Mazda Navajo

1 Answer

I have a stick shift problem, going to each gears, 1-5, it seems like the gears are still turning and have to wait a couple of seconds for the gears to slow down enough to engage recommended new/dealer oil is good, have about 280K miles on it. could i need to have a transmission rebuilt?

Posted by on

  • mltngrc Jun 09, 2009

    New clutch kit was installed also new clutch slave cylinder and rebalance, resurfaced flywheel, might it a defective slave cylinder?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,486 Answers

Replace the clutch..pressure plat not disengaging clutch plate fully.Fit new clutch kit

Posted on Jun 03, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hyundai tiburon running at high rpms when shifting


hmmm....it would seem as if your trans is having a bit of a hard time shifting so its sort of waiting before it can shift to the next gear (possible the gear system is having a problem shifting due to it sticking to some gears) i'd have to say....a mechanic can take a look to see why its seemingly shifting late at high RPMs to me IMO the trans is just having a hard time shifting with gears wanting to stick together making the whole trans have a hard time shifting

Jan 05, 2017 | Hyundai Cars & Trucks

1 Answer

My gear is stiff and experiencing a difficulty when engaging second gear. other gears seems to be fine but the shifting is not smooth.


I suspect that it will be in the shift mechanism
If it is a cable shift then replace the cable
If it levers or other linkages check and adjust or lubricate as required
I doubt it is in the clutch as you haven't mentioned difficulty in selecting first gear only shifting from 1 to 2nd.

Jun 21, 2015 | Opel Corsa Cars & Trucks

2 Answers

When I turn the ignition switch to start the vehicle I often cannot shift the stick shift out of Park. If I immediately try to switch gears after starting the engine it usually works but if I leave it more...


ok the safety feature on an auto gearbox is that the gear select has a solinoid lock on the shift & you norm have to start engine first before you can select drive now if the engine is running & not allowing you to select a drive then for some reason the solinoid is losing its signal or going faulty or even the shaft needing a little lube IE: wd40 now my volvo won't even allow me to take the key out untill its in park hope this helps

Aug 16, 2014 | 2008 Ford Escape

3 Answers

I have a 2001 elantra. What would make it stay in reverse and 1st gear.it is a manual transmission


when you put it in reverse,first thing you feel a spring.after tthat you lift,
a security plate,this plate prevent you from going reverse into 1 gear.
cause the axel turn a little further when you allreddy has stop the car.
this takes two sec.thats why when putting it in reverse after you feel the spring you wait two seconds,then puch al the way in reverse.

Jul 26, 2014 | 2001 Hyundai Elantra

1 Answer

Delay in Auto shifting from 2nd to 3rd gear


Check your ignition coils. One of mine was bad and when I replaced it, the shifting issue stopped.

Apr 22, 2013 | 1997 Nissan Maxima

2 Answers

I have a 1998 Buick Park Avenue. 94K. Transmission seems fine, but sometimes feels rough (knocks) between gears. Then, if I turn the car off and wait a few seconds, it seems to "reset" and begins...


Could be something sticking.Trans filter should be changed at least every 40,000-50,000 miles.If it has never been changed or has over 50,000 since the last filter service would start with a fluid flush and filter change.Well hope this helps, and good luck.

Mar 23, 2010 | 1998 Buick Park Avenue

1 Answer

Transmission shifts erratically


make sure the fluids full, start it then shut off,and immediatly pull the stick as the engine stops. and is the speedo working constant when hot? could be a speedo senor too

Aug 24, 2009 | 1992 Honda Accord

1 Answer

I have a 1992 saturn automatic 2 door and sometimes when i come to a stop it seems to have no gears or not shift to the other gears on its own any thoughts?


So you have to turn the engine off and wait for a couple of minutes? When it doesn't work from a stop does it just rev up like it's in neutral?

Jun 24, 2009 | 1992 Saturn SC

2 Answers

Sticks coming out of 1st 3rd and 5th gear.


all the gears at the top of the shift pattern use the same syncro.

your synchro's are starting to wear out.

Apr 11, 2009 | 1988 Chevrolet S-10

Not finding what you are looking for?
1993 Mazda Navajo Logo

Related Topics:

212 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8195 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...