Question about 2006 Chevrolet Silverado 1500 2WD

1 Answer

How difficult to replace inner tie rod end on 06 silverado 2wd?

Need to replace inner tie rod end is this a hard jod 2 do at home?

Posted by on

  • family1st09 Jun 03, 2009

    Hey Molson thanks sounds easy enuff.

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Chevrolet Master
  • 3,854 Answers

Not that hard, just spray the tie rod sleeve with WD40 night before and let it soak in. Remove the collier pin and and nut and hammer the old inner tie rod end out of the Track rod with a 5 pound sledge hammer. Remove the inner tie rod end from the sleeve and don't forget to mark the distance so you can place the new tie rod end at the same length. Reinstall the inner tie rod end to the Track rod and tighten the nut and replace the collier pin with a new one. Grease the fitting and go for a test drive, if the truck does not wonder then your good to go with out a alignment. Good luck and hope this helps, Note, make sure you have to right inner tie rod ends. Each side has different thread rotations.

Posted on Jun 03, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Chevrolet diagrams


Mary, 2003 Chevrolet Silverado 2500HD suspension and steering diagrams. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
2003 Chevrolet Silverado 2500 Parts GM Parts Department Buy genuine GM...
2003 Chevrolet Silverado 2500 HD Parts GM Parts Online GM Parts Direct
Chevrolet Silverado 2500 HD Ball Joints eBay
How To Install Replace Inner Tie Rod Chevy Silverado GMC Sierra 99 06...

Aug 02, 2014 | 2003 Chevrolet Silverado 2500HD

1 Answer

Have anyone out there ever change inner tie rods on a1995 honda odyssey?,if so simply explain,THANKS


Procedure on replacing the inner tie rod ends:


1) Raise and safely support the vehicle.

2) Remove the front wheel/tire assembly.

3) Clean the steering rod between the steering boot and outer tie rod end lock nut with a suitable penetrating lubricant and a clean cloth or shop towel.

4) Loosen the outer tie rod end locking nut 1/8 turn.

5) Loosen the steering boot clamp(s), and slide the small clamp off the boot.

6) Carefully loosen the boot and slide outward off the steering rack and onto the shaft to expose the inner steering rod mounting fastener.

7) If necessary, position the inner steering rack shaft in or out to allow for additional access.

8) Relieve the steering rod nut locking tab from the inner steering rack shaft, then loosen the steering rod ball socket nut 1 turn.

9) Matchmark the tie rod end to the threaded shaft.

10) Remove the cotter key and castle nut from the outer tie rod end threaded spindle, and using a tie rod end removal tool, remove the tie rod from the steering knuckle.

11) Hold the tie rod with a wrench, and remove the outer tie rod end from the threaded rod, counting the number of complete turns it takes to remove the tie rod end from the shaft. Write the number of turns on a piece of note paper.

12) Remove the tie rod end lock nut from the threaded steering shaft.

13) Slide the steering rack boot off the shaft.

14) Remove the inner steering rod ball socket nut from the inner steering rack shaft.

To install:

1) Inspect the tie rod end for looseness, and the steering rack boot and tie rod end boot for cracks deterioration or damage and replace as necessary.

2) Clean steering rack shaft and apply a light coating of Genuine Honda Power steering fluid as necessary.

3) Apply a medium strength locking agent to the threads where the inner steering rod ball socket mounts. Use a new locking washer and a new stop washer, and install the inner tie rod onto the steering rack shaft.

4) Tighten the inner tie rod end fastener by 58 ft. lbs. (78 Nm)

5) Peen the lock washer over the nut or onto the flat surface of the steering rack shaft.

6) Apply silicone grease to the outer circumference of the inner tie rod end ball socket, and onto the groove just outside of the socket.

7) Apply silicone grease to the inside of the small end of the steering rack boot, and slide the boot over the steering shaft and onto the rack and install the boot clamps. If the boot has air hose fittings make sure they are installed as removed.

8) Apply a light film of an anti-seize compound onto the threaded tie rod end, and install the tie rod end lock nut.

9) Install the tie rod end onto the tie rod, turning it in exactly the number of turns it took to remove it.

10) Install the tie rod end following the tie rod end installation procedure.

11) The balance of installation is the reverse of the removal procedure.

12) Check the front end alignment and adjust as necessary.

Sep 10, 2012 | 1995 Honda Odyssey

1 Answer

Where is the inner left and right tie rods at on a 2003 Chevy Silverado Just need to know exactly where they are


The inner tie rod ends are on the other end of the same rod as the outer tie rod ends. They should connect to the drag link and look almost identical to the outer tie rod ends. Hope this helps.

Sep 11, 2011 | 2003 Chevrolet Silverado 1500

1 Answer

I need to rplace the inner tie rods.


Inner tie rods rarely if ever need to be replaced in my experience: outer tie rod ends are far more common. Its not impossible so here's how.

1. remove the tie rod ends from the knuckle.
2. remove the clamp for the rubber bellows on the rack ends, and slide the bellows down the rod.
3. Turn the rack to fullleft or right as needed to get access to the inner rod end that screws into the rack.
4. There's a lock tab that has to be bent flat. This locks the rod end into the rack.
5. You'll need a (probably) 32mm wrench to undo the rod end from the rack.
6. Note how the lock tab is fitted to the rack/rod end.

7. Put in the new tie rods.

If your garage mechanic told you the inner tie rods are worn out, I'd ask why they think so. At step 4. above, try rotating the rod. This should be quite difficult. There should be NO evidence of slop or wear in the inner joint. What more commonly wears is the bushes on the end of the rack. These bushes are easily replacable with the rack in the car.The tie rods have to be removed to do this. So, when the rods are off, inspect the rack bushes for wear.

SD

Jun 25, 2011 | 2003 Mitsubishi Outlander

1 Answer

Inner tie rod removal


The first step in replacing the inner tie rod is to remove the tie rod end. It's basically a three step process, where you start by loosening the jam nut that's used to set the alignment (toe-in or toe-out). That jam nut determines how far up the inner tie rod the tie rod end is fixed. The tie rod end is hollow and threaded, so it can be screwed on or off the inner tie rod. Any procedure for removing a tie rod will start by telling you to count the turns you unscrew the tie rod end, something that I didn't do, and I'll save the explanation for the end:-) After you loosen the jam nut, you remove the cotter pin from the post on the outer tie rod ball joint, and unscrew the nut that holds the ball joint into the tapered fitting on the steering knuckle (video to right). After you pop the outer tie end free of the steering knuckle, you can unscrew the tie rod end. from the inner tie rod, but you need to grip it with something. Inner tie rods normally have some flat surfaces or a splined surface for grabbing with pliers. In this case, I needed two pairs of visegrips and a clamp to hold the visegrips on the inner tie rod from moving in order to get the outer tie rod end broken free and turning easy. That video is below. I happen to own the shop manuals for my Dodge Omni, so I was able to study the procedure for replacing the inner tie rod in detail. I didn't follow it for a couple reason. First, they show my type of power steering rack (Saginaw vs TRW) needs to be removed from the car to change the inner tie rod. That's a lot of extra work, not to mention the fact I buried one of the crossmember bolts in my unibody and flooring repair! So I went with an inner tie rod removal kit from Harbor Freight, manufactured by U.S. General (in Taiwan). The tool is very simple, basically a large steel tub with a snap in opening for a large crows foot insert on one end and a 1/2" socket drive on the other end. The kit is shown in the photo to the lower left (which I need to replace), and a video of the procedure is shown below. The kit wasn't quite right for my car, I had to use an oversized crows foot and the ball joint housing on the inner tie rod was too long, so the flats on the housing were barely held with the crows foot positioned by hand at the very end of the tool. But I got it out.

Dec 16, 2010 | 1992 Buick LeSabre

1 Answer

How to install inner and outer tie rods on a 2004 Chrysler Pacifica - I waqs told buy a trusted local mechanic that I need to replace 3 of the 4 tie rods. Might as as well replace all 4, but how hard is it...


You will need to rent or borrow in inner tie rod tool but here are the directions.
1. Break the jam nut on inner tie rod to outer loose.
2. Remove nut from outer tie rod attaching it to steering knuckle.
3. Use hammer to get tie rod out of knuckle.
4. Unscrew outer tie rod then jam nut
5. Remove clamp from boot and slide off inner tie rod.
6. Using side cutter or hammer and chisel break off metal clamp on the inside of inner tie rod boot.
7. Using inner tie rod tool, unscrew inner tie rod from rack and pinion
8. Reinstall parts and have it aligned

May 06, 2010 | 2004 Chrysler Pacifica

1 Answer

How hard is it to replace a outside tie rod end on a 95 dodge neon and how.


take the wheel off, there is a nut on the tie ron locking the tie rod end in place loosen this up (only break it free do not back way off) now take the nut offthe tie rod end that goes into the spindle, Hit the side spindle with a hammer right were the end goes in while pulling up on the tierod end (may take a few hard hits)> Now that you have the end out of the spindle you can unscrew the tie rod end from the inner tierod.*******NOTE*******measure the distance between the locknut on the inner tie rod to the middle of the outer tierod end,You want to keep that same distance or your car will pulll to one side and you'll need a wheel allignment.

Dec 30, 2009 | 1995 Dodge Neon

1 Answer

Loose inner tie rods on '97 Dodge Dakota Sport 2WD


corect size wrench should work. count the number of turn it takes to remove each unit make note and install new units using those numbers

Jun 28, 2009 | 1997 Dodge Dakota

2 Answers

Repalcement process on inner tie rods 05 silverado


undo bolts on inner and outer tie rods,u might need balljoint fork separator or 2 jaw puller to take them off of relay rod and steering knuckle,measure lenght of tie rod,loosen tube clamp and undo tie rod from tube,when installing make sure lenght is the same as before or wheel alignment will be off!

May 12, 2009 | 1992 Chevrolet K1500

Not finding what you are looking for?
Cars & Trucks Logo

2,517 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

79847 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...