Question about 2000 Buick LeSabre

Open Question

The airbag light in my Lesabre stays on. I had the dealer run a diagnostic and the the airbag code they said was showing up is is B0026. They said it was a faulty airbag coil? Can I replace that myself? Where is it?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2841 Answers

SOURCE: My 2003 Impala's Airbag Light stays on when I

Working on the SRS can be very hazardous. For this reason I suggest you have this done by a professional. I would for sure get a second opinion on this.

Posted on Oct 11, 2009

Testimonial: "Good advice, thx"

  • 58 Answers

SOURCE: any ideas on how i can diagnostic procedures for

Code B0026 is a code for a malfunction in your steering wheel Sir coil circuit.It is possible that replacing the SIR coil may solve your problem.The coil is located on the steering column under the steering wheel.

Posted on Nov 07, 2009

  • 3 Answers

SOURCE: car cut out and will no longer start. diagnostics

Check all conections to the coil pack, check to insure all spark plug wires are on, and make sure it is getting fire. With the engine not starting, the check engine light may not come on to produce a code for the diagnostics.

Posted on Feb 12, 2010

ZJLimited
  • 17970 Answers

SOURCE: CODE B0026 HOW DO i RESOLVE?

The airbag connectors in behind the front kick panels have high resistance. The fix is to replace them. Here is TSB's

#05-09-41-001B: Supplemental Inflatable Restraint (SIR) Light ON, Diagnostic Trouble Codes (Inspect/Replace IP Harness to Inflatable Restraint Module (Air Bag) Yellow 4-Way Connector C221 and/or C222) - (Jun 2, 2008)

Subject:
Supplemental Inflatable Restraint (SIR) Light ON, Diagnostic Trouble Codes (DTC) B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044 (Inspect and/or Replace IP Harness to Inflatable Restraint Module (Air Bag) Yellow 4-Way Connector C221 and/or C222)

Models:
2003-2006 Cadillac Escalade Models
2003-2006 Chevrolet Avalanche, Suburban, Tahoe
2003-2007 Chevrolet Silverado (Classic Only)
2003-2006 GMC Yukon, Yukon XL, Yukon Denali, Yukon Denali XL
2003-2007 GMC Sierra (Classic Only)

This bulletin is being revised to add the 2007 model year for pickups and change a part number. Please discard Corporate Bulletin Number 05-09-41-001A (Section 09 -- Restraints).

Condition
Some customers may comment that the Service Supplemental Inflatable Restraint Light is on.

Diagnosis with a scan tool may indicate a DTC B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044.

Cause
The most likely cause of any one of the following DTCs: B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044 is improper connection/high resistance in the IP harness to inflatable restraint module connector C221 and/or C222.

Diagnostic Information
DTC B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044 will set when one of the following conditions occur:
• The SDM detects the air bag module deployment loop resistance is greater than 4.8 ohms for 500 milliseconds.
• The SDM detects that the voltage at the air bag module high control is less than 2.4 volts and deployment loop resistance is 6 ohms or greater for 500 milliseconds.
• For additional diagnostic information, refer to DTC B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044 in the appropriate SI Document.

Correction

DO THIS
Test for proper connection/high resistance at connector C221 and/or C222.

Don't Do This
DO NOT replace SIR system components prior to testing for proper connection/high resistance in C221 and/or for DTCs B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044.

Caution: When performing service on or near the SIR components or the SIR wiring, the SIR system must be disabled. Refer to SIR Disabling and Enabling Zones. Failure to observe the correct procedure could cause deployment of the SIR components, personal injury, or unnecessary SIR system repairs.

Important: The IP harness to inflatable restraint module connectors C221 or C222 is NOT located at the base of the steering column...
• C221 (4 Cavities) -- I/P Harness to Body Harness, behind the left kick panel
• C222 (4 Cavities) (w/o HP2) -- I/P harness to body harness, behind the right kick panel
• C222 (4 Cavities) (w/HP2) -- Behind the left side I/P access panel
• Refer to the Master Electrical Component List for additional location information.

1. Remove the appropriate side door sill plate.
2. Remove the appropriate side hinge pillar panel.
3. Locate the IP harness to inflatable restraint module yellow 4-way connector C221 or C222.
4. Inspect the IP harness to inflatable restraint module connector C221 or C222 for proper connection.
5. Disconnect and reconnect the IP harness to inflatable restraint module connector C221 or C222 THREE times.
6. Clear the DTC and road test the vehicle.
• If DTCs B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044 DOES NOT reset, no additional repairs are necessary. Continue with step 10.
• If DTCs B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044 DOES reset, the most likely cause is high resistance in the IP harness to inflatable restraint module connector C221 or C222. Continue with the next step.
7. Replace the appropriate connector C221 and/or C222, P/N's 15306186 and 88987998. Refer to SIR/SRS Wiring Repairs (SI Document ID #325229).
8. Road test the vehicle and confirm that the repair is complete.
9. Install the driver's side hinge pillar panel.
10. Install the driver's side door sill plate.

Parts Information
Part Number: 15306186
Description: Connector (4-way Female, w/Leads) - Qty 1

Part Number: 88987998
Description: Connector (4-way Male, w/Leads) - Qty 1


Hope this help (remember comment and rated this help).

Posted on May 07, 2010

jsmes1027
  • 749 Answers

SOURCE: The engine runs rough and periodically stalls upon

Try unplugging the mass air flow sensor or tapping on it when it is running and listen for idle changes.The mass air flow sensor is located on top of the throttle body and is a rectangle held in place by tamper proof torx screws.If you unplug this the engine light will come on but if it stays running while driving then you can be pretty certain this is causing a problem.

Posted on Jul 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What does code 33 mean 2006 Grand Marquis airbag


Mercury Grand Marquis diagnostic code 33 Questions ...

www.fixya.com > ... > diagnostic code 33 > Cars & Trucks > Mercury
Mercury Grand Marquis cars & trucks diagnostic code 33 questions and ... 2006Mercury Grand Marquis air bag light flashes ... What does code po1151 mean.

2006 Mercury Grand Marquis air bag light flashes three ...

www.fixya.com/.../t19845434-2006_mercury_grand_marquis_air_bag_l...
Sep 3, 2013 - It then stay on. I assume - Mercury 2006 Grand Marquis question. ...What does a flashing air bag light mean on a 1993 Grand Marquis? Jul 23 ...

Mercury Grand Marquis airbag code 33 Questions ... - Fixya

www.fixya.com > ... > Tags > airbag code 33 > Cars & Trucks > Mercury
Mercury Grand Marquis cars & trucks airbag code 33 questions and answers. ... What does a flashing air ... 2006 Mercury Grand Marquis air bag light flashes.Missing: mean

Jan 11, 2016 | 2006 Mercury Grand Marquis

1 Answer

2004gmcyukonb0026


DTC B0026 LF/Driver Frontal Deployment Loop (Single Stage or Stage 1) Open circuit.
WARNING! Do not attempt to repair this without factory manual to explain disarming the system.

May 16, 2012 | Cars & Trucks

1 Answer

2009 chevy impala left front side deployment loop resistance B0014 above threshold


the following link covers yours reqest The driver frontal loops 1 and 2 are the loops to the steering wheel air bag. The SDM(sensing and diagnostic module for the air bag) is seeing these circuits as open. There is a bullitin for problems with a loose connection for the yellow connector behind the left kick panel(right behind the e brake and hood release). I would remove the kick panel, and disconnect and reconnect the connector a couple times. See if the light goes out. Or wiggle and move the connector with the key on, as the light should go out if it makes good connection. If it does go out you need to replace this connector. Good luck.

#05-09-41-001B: Supplemental Inflatable Restraint (SIR) Light ON, Diagnostic Trouble Codes (Inspect/Replace IP Harness to Inflatable Restraint Module (Air Bag) Yellow 4-Way Connector C221 and/or C222) - (Jun 2, 2008)

Subject:Supplemental Inflatable Restraint (SIR) Light ON, Diagnostic Trouble Codes (DTC) B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044 (Inspect and/or Replace IP Harness to Inflatable Restraint Module (Air Bag) Yellow 4-Way Connector C221 and/or C222)
Models:2003-2006 Cadillac Escalade Models
2003-2006 Chevrolet Avalanche, Suburban, Tahoe
2003-2007 Chevrolet Silverado (Classic Only)
2003-2006 GMC Yukon, Yukon XL, Yukon Denali, Yukon Denali XL
2003-2007 GMC Sierra (Classic Only)


This bulletin is being revised to add the 2007 model year for pickups and change a part number. Please discard Corporate Bulletin Number 05-09-41-001A (Section 09 -- Restraints).

<A href="#ss1-2146754">
Condition
Some customers may comment that the Service Supplemental Inflatable Restraint Light is on.

Diagnosis with a scan tool may indicate a DTC B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044.

<A href="#ss2-2146754">
Cause
The most likely cause of any one of the following DTCs: B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044 is improper connection/high resistance in the IP harness to inflatable restraint module connector C221 and/or C222.

<A href="#ss3-2146754">
Diagnostic Information

DTC B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044 will set when one of the following conditions occur:
• The SDM detects the air bag module deployment loop resistance is greater than 4.8 ohms for 500 milliseconds.
• The SDM detects that the voltage at the air bag module high control is less than 2.4 volts and deployment loop resistance is 6 ohms or greater for 500 milliseconds.
• For additional diagnostic information, refer to DTC B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044 in the appropriate SI Document.
<A href="#ss4-2146754">
Correction
DO THIS

Don't Do This

Test for proper connection/high resistance at connector C221 and/or C222.

DO NOT replace SIR system components prior to testing for proper connection/high resistance in C221 and/or for DTCs B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044.

Caution: When performing service on or near the SIR components or the SIR wiring, the SIR system must be disabled. Refer to SIR Disabling and Enabling Zones. Failure to observe the correct procedure could cause deployment of the SIR components, personal injury, or unnecessary SIR system repairs.



Important:
The IP harness to inflatable restraint module connectors C221 or C222 is NOT located at the base of the steering column.
• C221 (4 Cavities) -- I/P Harness to Body Harness, behind the left kick panel
• C222 (4 Cavities) (w/o HP2) -- I/P harness to body harness, behind the right kick panel
• C222 (4 Cavities) (w/HP2) -- Behind the left side I/P access panel
• Refer to the Master Electrical Component List for additional location information.


  • <LI type=1>Remove the appropriate side door sill plate. <LI type=1>Remove the appropriate side hinge pillar panel. <LI type=1>Locate the IP harness to inflatable restraint module yellow 4-way connector C221 or C222. <LI type=1>Inspect the IP harness to inflatable restraint module connector C221 or C222 for proper connection. <LI type=1>Disconnect and reconnect the IP harness to inflatable restraint module connector C221 or C222 THREE times. <LI type=1>Clear the DTC and road test the vehicle. • If DTCs B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044 DOES NOT reset, no additional repairs are necessary. Continue with step 10.
    • If DTCs B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044 DOES reset, the most likely cause is high resistance in the IP harness to inflatable restraint module connector C221 or C222. Continue with the next step.
    <LI type=1>Replace the appropriate connector C221 and/or C222, P/N's 15306186 and 88987998. Refer to SIR/SRS Wiring Repairs (SI Document ID #325229). <LI type=1>Road test the vehicle and confirm that the repair is complete. <LI type=1>Install the driver's side hinge pillar panel.
  • Install the driver's side door sill plate.
<A href="#ss5-2146754">
Parts Information
Part Number

Description

Qty

15306186

Connector (4-way Female, w/Leads)

1

88987998

Connector (4-way Male, w/Leads)

1 Service Airbag Have Codes Ask the GM Technician

May 01, 2012 | Chevrolet Impala Cars & Trucks

1 Answer

How to reset airbag light in 1998 buick lesabre


Light is on because the system has detected a fault. A code read is needed to discover the nature of the fault and then after repair dedicated diagnostic equipment will be needed to clear the code.

Sometimes the airbag light will stay on when the passenger airbag is switched off, if it has that facility.

The actual problem might not be the airbag but the seatbelt pretensioners.

Mar 12, 2012 | Buick LeSabre Cars & Trucks

2 Answers

2002 chevy truck.Code B0026


Hello and welcome. code B0026 is for a airbag malfunction. this code will require a high end scan tool, like a GM tech 2 scan tool to check out.this code is related to a deployment loop problem on the drivers side of vehicle

• DTC B0026 will set when one of the following conditions occurs:
- The SDM detects the steering wheel module deployment loop resistance is greater than 4.8 ? for 500 milliseconds. - The SDM detects the voltage at steering wheel module high signal is less than 2.4 volts and steering wheel module deployment loop resistance is 6 ? or greater for 500 milliseconds.The inflatable restraint steering wheel module deployment loop consists of a steering wheel module, steering wheel module coil, steering wheel module high signal circuit, and steering wheel module low signal circuit. Shorting bars are used on the steering wheel module connector as well as the steering wheel module coil connector which will short together the steering wheel module high and steering wheel module low signal circuits when the connector is disconnected. This will help to prevent unwanted deployment of the inflator module during servicing. When the ignition is turned ON, the inflatable restraint sensing and diagnostic module (SDM) performs continuous diagnostic tests on the deployment loops to check for proper circuit continuity and for shorts to ground or voltage. If a malfunction is detected, a DTC will be stored.

Sep 12, 2010 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

CODE B0026 HOW DO I RESOLVE? REAR DOOR LOCKS NOT WORKING, SERVICE BRAKE BOOSTER WARNING ON, AIRBAG LIGHT ON, SERVICE AIRBAG WIRNING, INTERMIT NO START. HELP MEEEE!!!!!!


The airbag connectors in behind the front kick panels have high resistance. The fix is to replace them. Here is TSB's

#05-09-41-001B: Supplemental Inflatable Restraint (SIR) Light ON, Diagnostic Trouble Codes (Inspect/Replace IP Harness to Inflatable Restraint Module (Air Bag) Yellow 4-Way Connector C221 and/or C222) - (Jun 2, 2008)

Subject:
Supplemental Inflatable Restraint (SIR) Light ON, Diagnostic Trouble Codes (DTC) B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044 (Inspect and/or Replace IP Harness to Inflatable Restraint Module (Air Bag) Yellow 4-Way Connector C221 and/or C222)

Models:
2003-2006 Cadillac Escalade Models
2003-2006 Chevrolet Avalanche, Suburban, Tahoe
2003-2007 Chevrolet Silverado (Classic Only)
2003-2006 GMC Yukon, Yukon XL, Yukon Denali, Yukon Denali XL
2003-2007 GMC Sierra (Classic Only)

This bulletin is being revised to add the 2007 model year for pickups and change a part number. Please discard Corporate Bulletin Number 05-09-41-001A (Section 09 -- Restraints).

Condition
Some customers may comment that the Service Supplemental Inflatable Restraint Light is on.

Diagnosis with a scan tool may indicate a DTC B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044.

Cause
The most likely cause of any one of the following DTCs: B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044 is improper connection/high resistance in the IP harness to inflatable restraint module connector C221 and/or C222.

Diagnostic Information
DTC B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044 will set when one of the following conditions occur:
• The SDM detects the air bag module deployment loop resistance is greater than 4.8 ohms for 500 milliseconds.
• The SDM detects that the voltage at the air bag module high control is less than 2.4 volts and deployment loop resistance is 6 ohms or greater for 500 milliseconds.
• For additional diagnostic information, refer to DTC B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044 in the appropriate SI Document.

Correction

DO THIS
Test for proper connection/high resistance at connector C221 and/or C222.

Don't Do This
DO NOT replace SIR system components prior to testing for proper connection/high resistance in C221 and/or for DTCs B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044.

Caution: When performing service on or near the SIR components or the SIR wiring, the SIR system must be disabled. Refer to SIR Disabling and Enabling Zones. Failure to observe the correct procedure could cause deployment of the SIR components, personal injury, or unnecessary SIR system repairs.

Important: The IP harness to inflatable restraint module connectors C221 or C222 is NOT located at the base of the steering column...
• C221 (4 Cavities) -- I/P Harness to Body Harness, behind the left kick panel
• C222 (4 Cavities) (w/o HP2) -- I/P harness to body harness, behind the right kick panel
• C222 (4 Cavities) (w/HP2) -- Behind the left side I/P access panel
• Refer to the Master Electrical Component List for additional location information.

1. Remove the appropriate side door sill plate.
2. Remove the appropriate side hinge pillar panel.
3. Locate the IP harness to inflatable restraint module yellow 4-way connector C221 or C222.
4. Inspect the IP harness to inflatable restraint module connector C221 or C222 for proper connection.
5. Disconnect and reconnect the IP harness to inflatable restraint module connector C221 or C222 THREE times.
6. Clear the DTC and road test the vehicle.
• If DTCs B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044 DOES NOT reset, no additional repairs are necessary. Continue with step 10.
• If DTCs B0013, B0014, B0017, B0018, B0024, B0026, B0043, B0044 DOES reset, the most likely cause is high resistance in the IP harness to inflatable restraint module connector C221 or C222. Continue with the next step.
7. Replace the appropriate connector C221 and/or C222, P/N's 15306186 and 88987998. Refer to SIR/SRS Wiring Repairs (SI Document ID #325229).
8. Road test the vehicle and confirm that the repair is complete.
9. Install the driver's side hinge pillar panel.
10. Install the driver's side door sill plate.

Parts Information
Part Number: 15306186
Description: Connector (4-way Female, w/Leads) - Qty 1

Part Number: 88987998
Description: Connector (4-way Male, w/Leads) - Qty 1


Hope this help (remember comment and rated this help).

May 07, 2010 | 2003 Chevrolet Suburban 1500

2 Answers

Air bag light stays on


you have a code set have someone with a diagnostic scanner retrieve the codes and youll know what to replace

Jan 21, 2010 | 2003 Ford Explorer Sport

1 Answer

Any ideas on how i can diagnostic procedures for my airbag trouble code b0026? i have a 2003 impala


Code B0026 is a code for a malfunction in your steering wheel Sir coil circuit.It is possible that replacing the SIR coil may solve your problem.The coil is located on the steering column under the steering wheel.

Nov 06, 2009 | 2003 Chevrolet Impala

1 Answer

Airbag light stays on sometimes


GO TO A DEALER AND GET THEM TO RUN A DIAGNOSTIC TEST THIS SHOULD IDENTIFY THE FAULT

Aug 31, 2009 | 1998 Chevrolet Blazer

1 Answer

Airbag sensor light blinking


Take it to an independent specialist mechanic to get the codes read and a suggested plan of action

Aug 07, 2017 | 2002 Nissan Xterra

Not finding what you are looking for?
2000 Buick LeSabre Logo

Related Topics:

951 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...