Question about 2002 Dodge Grand Caravan

1 Answer

Heater fan switch only works on high speed setting

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 66 Answers

Check the heater resistor block in the heater housing. It controls the other speeds.

Posted on Jun 03, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I fix heater fan to operate at low and medium speeds. It only works on High.


depending on car some have a fan relay or its your switch itself

Jan 13, 2016 | Cars & Trucks

1 Answer

Fan speed switch


the problem will be in the fan resistor a small unit normally screwed into the heater case behind the glove box. The resistors that create the lower speeds will be burnt out leaving only the direct circuit for high fan

Dec 28, 2013 | Toyota Cars & Trucks

1 Answer

Heater fan only works on high


Replace the step switch, the contacts are burned out or just use it on high until that speed doesn't work...your choice..

Dec 31, 2012 | 2000 Buick Century

1 Answer

Heater fan motoer only works on high setting?


many of the heater blowers use a resistor type switch to adjust the fan speeds, when the switch goes bad only the high speed will work. the resistor is usually located in the airflow in the heater box under the dash. find it , change it (it just plugs in) and it will work again

Jan 16, 2011 | 1993 Buick Century

1 Answer

Heater & cooling fan only works on high.Power locks don't work.


there is a resistor for the heating and cooling fan speed. this controls the amount of voltage to your fan, which controls the speed. usually when the fan only works on high it will bypass the resistor and use the full 12 volts for the high setting. your power locks might be part of this circuit. i would check the resistor first then check the locks. usually the resistor is behind the high low switch

Mar 26, 2010 | 2000 Pontiac Montana

1 Answer

How do I remove 1996 honda accord heater fan switch? I'm not sure if I need a new switch. Heater fan works only on high speed "4"


if the fan/motor only works on max No 4 setting ? then may i suggest you have a resistor fault or commonly known as a reostat in uk this is the component that provides the relevent reduced speeds on selection but when it fails only max speed works so you should find this unit attached on heater fan exterior if you follow wires from actual motor it will connect to the resistor unit ? then onward to switch control it is not to difficult diy and if you have access to manual/ it will give location/access for renewing? hope this helps/inspires you to diy ?

Dec 23, 2009 | 2000 Honda Accord

1 Answer

Location of low speeds heater fan fuse & switch. I do not have a owners manual.


the switch is on the dash with the other a/c controls. does the fan work at all? high speed OK? but the lower speeds dont work? if any speeds other than high dont work, replace the blower resistor.

Oct 04, 2009 | 1999 Buick LeSabre

1 Answer

Heater fan only works on fastest speed


Your blower motor resistor has gone bad, it should be located next to your blower motor in the car, held in place with a couple of screws, remove it and replace it. The resistor is responsible for making the blower motor run at slower speeds than high or (4). Let me know if this helps.

Jun 16, 2009 | 2000 Ford Focus

2 Answers

Blower dosent blow on high


fan blower speed switch under hood usually in fire wall or in heater box under dash area if you do not change it you will keep losing all your speeds until nothing left! it is not!!!!the one in your dash that you hand operate! hope this helps.John

Jan 24, 2009 | 2006 GMC Envoy

3 Answers

Heat/AC Blower fan speed only works on High


Alot of people have the same problem with the fan switch and blown bulbs. There really is no fix for this. Jeep really screwed up when designing the heater control assembly. The cheapest solution is to buy another unit off Ebay. Can always go to the dealer but be ready to PAY for there mistakes.

Jan 14, 2009 | 2005 Jeep Grand Cherokee

Not finding what you are looking for?
2002 Dodge Grand Caravan Logo

266 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...