Question about 2005 Chrysler PT Cruiser

3 Answers

Code 344 camshaft sensor ciurcut intermitint 05 pt cruiser

Have same problem on 05 pt right now. Code is 344 camshaft sensor circut intermitint. Checked volts and its 5.00 Car will drive fine for about 2 miles the light comes back on and RPMs wont go over 2000. Changed cam sensor but that would be to easy.Problem is still there.Checked wiring harness for cam sensor and computer connections. Any ideas????

Posted by on

  • yadayada
    yadayada May 11, 2010

    code 344 is not a valid code, no enough numbers and no letter.

×

3 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Im having exactly the same problem with a 2004 pt. took it to a dealer they told me ecm, replaced it and still the same problem. i changed out the cam knock sensor and the crank sensor. same thing. if i erase the code it will run perferct for an hour sometimes then same thing, light comes on and wont accelerate, over 2000 rpm. weird. im lost, it makes no sence.

Posted on Oct 07, 2011

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 11 Answers

Make sure your connector is clean and add some dielectric grease check connections to the computer .. again clean connectors and check all grounds that should fix it if its not a bad part or defective ....Mark

Posted on May 15, 2012

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 15 Answers

Check you tps sensor throttle postion sensor

Posted on Jun 03, 2009

  • JacobTD Jun 03, 2009

    check you tps sensor throttle postion sensor

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

PT cruiser engine warning


P0344 is camshaft Position sensor,Dont get confused with the camshaft sensor, You have a timing problem and your solution is the timing belt.

Jun 26, 2012 | 2006 Chrysler PT Cruiser

1 Answer

Got code po340 on 2008 Chrysler PT cruiser. Runs great sometimes when engine light on & rough at other times like not getting gas. Engine light does not come on every day either. Cam sensor or timing...


P0340: Camshaft Position Sensor A - Bank 1 Circuit Malfunction

- Camshaft Position Sensor harness is open or shorted
- Camshaft Position Sensor circuit poor electrical connection
- Faulty Camshaft Position Sensor
- Faulty starter motor
- Starting system circuit
- Dead (Weak) battery

Feb 08, 2012 | 2008 Chrysler Pt Cruiser

1 Answer

Whats the position of the crankshaft position sensor on 2005 pt cruiser non turbo


P0344 CHRYSLER - Camshaft Position Sensor Intermittent Interruption Bank 1 Sensor 1
Possible causes - Camshaft Position Sensor harness is open or shorted
- Camshaft Position Sensor circuit poor electrical connection
- Faulty Camshaft Position Sensor
- Faulty starter motor
- Starting system circuit

Dec 14, 2011 | 2005 Chrysler PT Cruiser

1 Answer

2002 PT Cruiser. Vehicle shut down while driving. Received P0340 Trouble code..No camshaft position sensor signal at pcm. I replaced Position Camshaft Sensor, book suggests life on these 5-10 years, It...


This could be related to a loose camshaft drive belt. If you have slack in the belt the camshaft will rebound on over run causing the P0340. It can also be a Crackshaft sensor problem too.(P0335) Hope this helps...

Mar 06, 2011 | 2003 Chrysler PT Cruiser

1 Answer

I need to now what code 344 is on a 05 dodge 1/2 ton


code of P0344= camshaft position sensor "A"--circuit intermittent (bank 1)

Feb 03, 2011 | Dodge Ram 1500 Cars & Trucks

2 Answers

Camshaft sensor malfunction...code 0340.


i believe it is on the drivers side end of the head, accesable from the top.

Nov 13, 2009 | 2004 Chrysler PT Cruiser

2 Answers

After changing the camshaft censor and the car still wont start what could be the problem also is there a fuse that needs to be replaced this is a 2004 pt cruiser the code say its the camshaft censor also...


P0016 crankshaft/camshaft timing misalignment
p0340 camshaft sensor

intermittent crankshaft sensor

PCM detects an error when the camshaft position is out of phase with the crankshaft position

Sep 26, 2009 | 2004 Chrysler PT Cruiser

1 Answer

2002 pt cruiser Camshaft Sensor


change the crankshaft positon sensor in the rear of the engine above the oilfilter. Also check the wiring to this sensor, they have a problem shorting out. You have to change the camshaft and crankshaft sensors at the same time. Make sure you give your car a major tune up. Did you check yor starter?.........runjoe

Feb 04, 2009 | 2002 Chrysler PT Cruiser

Not finding what you are looking for?
2005 Chrysler PT Cruiser Logo

1,271 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...