Question about 1999 Oldsmobile Cutlass

1 Answer

Replacing 1999 oldsmobile cutlass headlight bulb

I need to know how to replace the driver side headlight bulb on 1999 oldsmobile gls

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Oldsmobile Master
  • 3,640 Answers

Remove the pins and the plastic shield over the headlight housing.pull straight up on the 2 clips to release housing from ball studs , twist and withdraw the bulbs from housing!! do not touch bulbs, oil from skin will make them blow out quicker, if need be use a pair of clean gloves to be safe, installation the reverse of removal!!!

Posted on Sep 02, 2009

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 10865 Answers

SOURCE: Low beam, driver's side headlight

The low beam bulb needs to be replaced. Go to an autozone store as they will sell you the bulb, and even assist you in their parking lot with installing it.

Posted on May 06, 2009

  • 2 Answers

SOURCE: Driver side headlight bulbs burned out on 2003 VW Golf

There is a light cover in front of the battery... take this off and then look for the metal clamps holding the light housing in.  (I say clamps, but they're more like glorified paper clips on either side of the fixture.)  Press in on each side, pushing the clamps towards each other and pull the fixture out.

Posted on Dec 04, 2008

  • 5 Answers

SOURCE: 99 cutlass supreme headlight bulb replacement

Look at the top of the headlight assembly. There is a plastic panel on top of the assembly that is held in place by two plastic pins. Remove those pins by lifting the center of the pin and then pull out the pin. Remove the panel. Then you will find two small plastic levers that will lift about 1/2 inch. They do not come out but they will release two studs that secure the assembly. After the assembly is released, slide it forward to access the bulbs you need to replace. Installation is the reverse of these procedures.

Posted on Mar 08, 2009

  • 383 Answers

SOURCE: 2001 subaru outback headlight not working

chapmnfarm: your head lights use a "2" fuse system.
one for the left and one for the right.
The fuse box you are looking for is under the hood on the passenger's side. It is a black box roughly 8 inches long and 4-5 inches wide. When you remove the cover, you will see fuses and relays. What you are looking for is the section in the box which has a cluster of 7 fuses. 3 in one row and 4 in the other. On the outer parameter are two relays. The fuses you are interested in are located in the row of 4 fuses, with the two closest to the "L" shaped part of the box. Both of those should be 15 amp fuses.
The fuse below those should be a 20 amp which is the lighting switch and the one below it is a 15 amp which is for the interior lights and the clock.
Check your harness grounds in the engine compartment near the area you have the problem. There are ground wires which come out of the harness on both sides of the core support. The wires are black in color and have "EYES" crimped onto the ends of the wires. Both of them will probably be located about 4-6 inches below the upper tie bar on each side of the radiator. Odds are that the eyes will be large enough to pass a 6mm bolt through.
I hope what I have given you will resolve your problem. Lem me know,,good luck>>>>>>>>>>>>>>>

Posted on Apr 19, 2009

  • 37 Answers

SOURCE: Headlight bulb replacement for 2002 Hyundai

http://www.autozone.com/autozone/repairinfo/common/repairInfoMain.jsp?targetPage=productsHowToInspect&leftNavPage=productsHowTo&pageId=%090900c15280213e7e&subtitle=replace

Posted on Apr 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace the glove box latch on a 1998 Oldsmobile Cutlass GLS?


Most will have a row of screws just across the bottom of the door, either on the outside(look up from the floor) or a row of screws inside the door. Open the glove box and look at very bottom edge.

Aug 05, 2014 | 1998 Oldsmobile Cutlass

1 Answer

How do I fix headlight


You can't fix the headlight, you can only replace the assembly or change a bulb. First you must remove screws that hold side marker light and set aside. Then remove six screws that hold grill. Set aside. Now remove four 10mm bolts, two on each side of headlight assembly, and remove. Twist and remove bulb and reinstall in new assembly. Reinstall in reverse of disassembly.

Jul 11, 2014 | 1996 Oldsmobile Cutlass Ciera

1 Answer

Replace low beam drivers side headlight on 1993 olds cutlass supreme convertible


Remove turn signal assembly (uses a torx 15 driver). This will expose the two 10mm bolts on the one side of the headlight assembly. Remove the plastic front grill (uses a torx 15 driver - there are about 6 screws). This will expose the other two 10mm bolts on the headlight assembly. Remove the four 10mm bolts to remove the headlight assembly and this will allow you access to the headlight you need to replace.

Feb 18, 2011 | 1993 Oldsmobile Cutlass Supreme

1 Answer

I have a 99 oldmobile cutlass. The inner headlight bulb need to be replaced. Do i need to change the whole headlamp?


No, you just change the bulb. Open your hood, and look down at the rear of the headlamp. You will see a nylon bulb socket going into the rear of the headlight assembly. Squeeze the nylon lock, and turn the socket counter clockwise, and it pulls out. Pull the bulb out, and replace with a new one. Be careful not to touch the new bulb with bare fingers. The oil on your fingers will cause early bulb failure. Use a paper towel or garden glove to handle the bulb.

Nov 15, 2009 | 1999 Oldsmobile Cutlass

1 Answer

How do I change the bulb/headlight on a 93 olds cutlass ciera


behind ur headlights u should c the plug with wires it unscrews by hand counter clock wise

Apr 08, 2009 | 1993 Oldsmobile Cutlass Ciera

2 Answers

How do I change out headlight bulb on 91 olds cutlass cierra


Behind the headlight, you should see the nylon bulb holder. Turn it counter clockwise, about a 1/4 turn, and it should come out. Pull the old bulb straight out, and replace it with the new one. Don't touch the glass part of the new bulb with bare fingers, or you'll be replacing it again. Use cotton gloves or a paper towel. Put the holder back in the headlight, turn it clockwise until it locks.

Mar 09, 2009 | 1991 Oldsmobile Cutlass Ciera

1 Answer

How do i take the headlamp assembly out, on passanger side of a olds 98 cutlass? need to change a light bulb!


There are two round tabs on the top of the headlight assembly ,towards the back, just pull them up and the light should come out.

Mar 08, 2009 | 1999 Oldsmobile Cutlass

1 Answer

99 olds culass headlight bulb replacement


Look at the top of the headlight assembly. There is a plastic panel on top of the assembly that is held in place by two plastic pins. Remove those pins by lifting the center of the pin and then pull out the pin. Remove the panel. Then you will find two small plastic levers that will lift about 1/2 inch. They do not come out but they will release two studs that secure the assembly. After the assembly is released, slide it forward to access the bulbs you need to replace. Installation is the reverse of these procedures.

Feb 25, 2009 | 1999 Oldsmobile Cutlass

1 Answer

99 cutlass supreme headlight bulb replacement


Look at the top of the headlight assembly. There is a plastic panel on top of the assembly that is held in place by two plastic pins. Remove those pins by lifting the center of the pin and then pull out the pin. Remove the panel. Then you will find two small plastic levers that will lift about 1/2 inch. They do not come out but they will release two studs that secure the assembly. After the assembly is released, slide it forward to access the bulbs you need to replace. Installation is the reverse of these procedures.

Feb 25, 2009 | 1999 Oldsmobile Cutlass

1 Answer

Turn signal problem


step by step. 1.if other side rear works switch bulbs. if works replacement bulb no good. 2.doesnt fix it then carefully check wire to socket. if ok burnish the bulb contact in socket and outside a bit if socket uses outside as ground. 3. if this doesnt fix it; its out of my league and we need an expert. should be able to do this most american brand cars. oh! problem is that there is no complete circuit through the socket and bulb.

Oct 07, 2008 | 1999 Oldsmobile Cutlass

Not finding what you are looking for?
1999 Oldsmobile Cutlass Logo

Related Topics:

1,293 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...