Question about 2001 Chevrolet Blazer

1 Answer

My keyless remote for my 2000 jeep grand cherokee wont unlock the

I have a 2000 jeep grand cherokee and the keyless remote wont unlock the doors and when I hit the lock button it doesnt chirp like it used to and it wont lock the doors. How do I fix this?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 324 Answers

Go to autozone and use the remote tester on the counter to make sure that the remote itself is functioning or not, could be a dead battery. On some vehicles it is possible to reset the keyless entry by turning the ignition switch from off to run (right before the starter activates) 3 times or so, if you try this and the door locks activate then press the lock button on your remotes. good luck

Posted on Jun 03, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is my keyless entry attached to my key 2000 jeep cherokee


all locks.
is the car battery fully changed.
at 12.6vdc rested.?

Aug 31, 2014 | 2000 Jeep Grand Cherokee Limited

2 Answers

Keyless remote 1996 jeep grand cherokee laredo programing


Instructions
  1. Programming the First Transmitter
    • 1

      Unlock all of the Jeepicon1.png Grand Cherokee's doors and open the driver's side door. Keeping the door open, lock it using the manual lock on the door itself.

    • 2

      Put the manual key into the ignition and switch it to the "On" or "Run" position, whichever applicable, without starting the engine.

    • Sponsored Links

    • 3

      Point the remote at the receiver (located by the little bulb on the caricon1.png ceiling) and hold down the "Lock" button for up to 5 seconds.

    • 4

      When the driver's side door unlocks, you know the remote has been programmed correctly. If you are only programming one remote, jump to the next step. If not, manually re-lock the driver's side door and repeat steps 5 and 6 using each remote you would like to program and then continue.

    • 5

      Turn the key to the "Off" position and turn the ignition on immediately. This must be done within 20 seconds of programming the last remote. You're finished!

Sponsored Links

Read more: How to Program the Remote on a 1996 Jeep Grand Cherokee ' eHow.com http://www.ehow.com/how_7433787_program-1996-jeep-grand-cherokee.html#ixzz2KdCc5PQq

Feb 11, 2013 | 1996 Jeep Grand Cherokee

1 Answer

Keyless entry wont unlock


TThere is probably a problem with the door unlock relay or the passenger door module. The passenger door modules on Jeep Cherokee have had a lot of problems and there are a couple of Technical Service bulletins published by the manufacturer as a result of these failures.

Jun 02, 2012 | 2001 Jeep Cherokee

1 Answer

1999 grand cherokee doors unlock with key fob but when any of the doors are opened the alarm goes off and will turn off with the key in the igintion


dude it wont work but u gotta use the keyless remote to disable ur alarm! its in the manual under security like page 200's

Jan 31, 2010 | 1999 Jeep Grand Cherokee

1 Answer

I have a 1993 Jeep Grand Chorkee and just changed the battery. Now the Security system won't allow the car to start. HELP


Sounds like your security system module may have shorted out. Also the sensors on the lock mechanisms in the doors may be bad. I also have a 93 Grand Cherokee and the sensor in the rear hatch went bad on the lock. I now have to unlock it with the key using only the drivers door or unlock it with the keyless entry remote to unarm the security system.

Jun 28, 2009 | 1993 Jeep Grand Cherokee

1 Answer

Both of my keyless entry remotes just stopped working any ideas


sometimes you have to hold the lock and unlock at the same time and stand close to your jeep until the locks unlock and lock agian if that works then they are reset if not than try to change the batterys in one remote and retry

Mar 11, 2009 | 2000 Jeep Grand Cherokee

2 Answers

1999 jeep grand cherokee laredo keyless remote transmitter programing


Open the drivers door and turn the key to the on position. Lock the doors with the switch on the door. After the doors lock point the transmitter to the little bulb on the ceiling. Press the LOCK button and hold it until the doors unlock.

Maybe this info can be help you...
http://autorepair.about.com/library/faqs/bl868f.htm

Jan 20, 2009 | 1995 Jeep Grand Cherokee

Not finding what you are looking for?
2001 Chevrolet Blazer Logo

813 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...