Question about 1994 Oldsmobile Cutlass Supreme

1 Answer

Hazard/turn signal switch

No brake lights no turn signals and brake light warning lights on turn signals won't work hazard lights won't work and the brake lights won't work

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Need to replace the whole switch/stick at steering column.

Posted on Jun 13, 2009

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

joecoolvette
  • 5660 Answers

SOURCE: no brake/hazard lights,have running/turn signal lights

Suggest you change hazard flasher 'can' first, then go to the hazard switch. I'm betting it's the flasher can.

Posted on May 11, 2009

  • 389 Answers

SOURCE: 1992 Ford Ranger Turn signal/Hazard light issue

Can you just check to make sure the ignition key switch is not staying over to far and not backing off when you try to start it. I had a truck that did that and it messed up my turn signals until I brought the key switch back a little after starting it. Just a simple idea. Be kind with your rating for me. Raz

Posted on Apr 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

All my lights work on my 2005 ford focus except the lower brake lights and turn signals. all fuses are good.


Do you know anything about automotive electronics ?
Stoplamps
The stoplamps are part of the rear lamp assembly. When the brake pedal is applied, the stoplamp switch supplies voltage to the generic electronic module (GEM) and the high mounted stoplamp. The GEM then supplies voltage to the rear lamps.

Turn Signal Lamps and Hazard Warning Lamps
The turn signal lamps and hazard warning lamps system consists of:
  • Hazard switch
  • Multifunction switch
  • GEM
  • Turn signal lamps
When the multifunction switch is placed in the LH or RH turn positions, a voltage signal from the GEM is routed to ground. When the GEM detects the multifunction switch in the LH or RH turn position, the GEM supplies voltage to the appropriate turn lamps in a flashing manner. When operating correctly, the turn lamps flash approximately 80 times per minute.
When the hazard warning switch (located in the upper part of the center console) is switched on, a voltage signal from the GEM is routed to ground. When the GEM detects that the hazard switch is switched on, the GEM supplies voltage to all the turn signal lamps in a flashing manner. When operating correctly, the hazard lamps flash approximately 80 times per minute.

Do you know how to test electrical circuits with a DVOM - digital volt ohm meter , how to read an use a wiring diagram to pin point locations in a electrical circuit for testing B+ voltage an ground ?

Free wiring diagrams
http://www.bbbind.com/free_tsb.html Enter your vehicle info . year ,make , model an engine size . Under system click on lighting ,then under subsystem click on turn signal lamps . Click the search button then each blue link , one at a time .


Electric Testing Techniques You Need to Know
Basic Electricity for Service Techs Ohm law Current Flow Opens Shorts

May 07, 2017 | Ford Cars & Trucks

1 Answer

Why aren't hazard lights or brake lights working?


Brake lights /rear hazard lights not working - Ford Truck ...

www.ford-trucks.com > ... > 1967 - 1972 F-100 & Larger F-Series Trucks
Jul 9, 2010 - After checking the brake lights I tried the emergency flashers and found that they are working in the front but not in the back. I do have rear turn ... 1995 F350 Brake Lights / Turn Signals not working
Jul 9, 2012
Turn Signals and Brake Lights Do Not Work
Mar 10, 2012
Turn Signal, Brake Lights, & Rear Hazard not working
Aug 3, 2010
Rear Turn Signals, Hazards and Brake Lights not working....
Aug 29, 200

Sep 30, 2015 | Cars & Trucks

1 Answer

95 mustange gt brake light dont work check #9 fuses change all bulbs replaced switch on brake pedal hazards lights works ,parking or running lights works,turning signal lights works,what other places i...


I assume the fuse has power if the hazards work.
The third brake light skips the turn signal switch, the regular brake light circuit goes thru the turn signal switch.
Do you have power going into the turn signal switch on the red lite green wire from the brake switch ?

Feb 17, 2013 | 1995 Ford Mustang

2 Answers

!997 Ford Thuderbird brake lights and hazards do not work


Lets start at the beginning.
The turn signals and brake lights use different fuses but both go thru the turn signal switch and use the same bulbs.
Have you checked the fuses for each circuit and does each switch have power in and out ?

Feb 03, 2013 | 1997 Ford Thunderbird LX

1 Answer

Turn signal,brake lights not working


I would check for voltage at the turn signal switch. The brake lights go thru the turn signal switch, except for the high mount light.

Jul 24, 2012 | Cars & Trucks

1 Answer

Rear brake lights and turning signals not working. One tail light has been out for very long time, but brake lights and signals just stopped working few weeks ago.


I'm checking into that same problem for a early 90's buick ( it's a GM also ) , I've checked the obvious ( bulbs, flasher,fuses,etc) all where fine. I assume your front turn signals work if you manually operate the turn signal switch or put on the hazard switch? The Buick's rear lights won't come on even with the hazard switch on. When you say one tail light has been out for some time, do you mean the brake/signal light or park/running lights? The Buick was like that with one side out for a while ( brake/signal light) but both the rear park/running lights work. Now, I've narrowed the problem down to the turn signal switch. I'd bet money on it. I just have to dig out my steering wheel puller, bite the bullet and get 'er done. You should be carefull if you're attempting that repair yourself ( AIRBAG ), use a manual. ( You could do a quick test by trying the turn signal while you pull the bottom of the arm toward you,move some of the wiring in the column near the arm,etc. I did and the signals started working. Could be the switch,dirt or a broken/loose wire. there's a lot of wiring going through the column and a lot of movement ( turn signal,high beam,cruise, then add tilt) Hope this helped.

Sep 20, 2011 | 2001 Chevrolet Cavalier

1 Answer

I have no signals and when brakes lights are on, lose brake light to either side turn signal is set on


Hi!!

If you activate the turn signal switch and you step on the brake pedal, the turn switch (on the steering column) deactivates the brake light to make the signal light more visible. The bulb for the stop and turn lights is the same.

Turn hazard lights ON. If they don't blink, replace turn/hazard flasher, If one or more lights don't come on, replace bulb.

Check fuse and circuit wiring for broken or loose connections. If all looks fine, check following:

If front turn lights work fine, check brake/turn bulbs.

If turn lights come on but don't blink, replace turn signal/hazard flasher.

If front and back turn lights don't come on, replace switch on column.

Let me know how it worked out, Good Luck

Mar 24, 2010 | 1991 Plymouth Acclaim

2 Answers

2002 chevrolet cavalier, my brake lights, front and rear turn signals and hazard lights are not working


Your Hazard switch is bad. There were a bunch that had faulty soldering connections, and would fail prematurely. This circuit also competes with the turn signals, and the brake lights. Replace the switch with an aftermarket replacement, and it should fix your issue.

Dec 20, 2009 | 2002 Chevrolet Cavalier Coupe

1 Answer

No brake light or hazard warning flashers in rear


It appears to be the mutifunction switch. (Turn signal control). That, plus the 3 words in parenthesis wil come to 699.00 bucks. then we add the switch.... Just kidding. The multi finction switch is defective and about to fail altogether.. Sorry.

Oct 07, 2009 | 1998 Lincoln Town Car

1 Answer

Checked all fuses-good, swapped bulbs-good, hazard lights-good, head lights good, turn signals-good but no brake lights. 1995 chevy silverado


Does the turn signals or hazards work in the rear?? Yes... it may be the brake switch or the turn signal switch (power goes from battery, to the brake switch then to the turn signal switch, then to the lights. No? .. again.. possibly turn signal switch or the wiring between cab and bed.

Jun 04, 2009 | 1996 Chevrolet K1500

Not finding what you are looking for?
1994 Oldsmobile Cutlass Supreme Logo

388 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...