Question about 2000 Dodge Grand Caravan
Ok we bought the window motor and replaced it today,.now the window will roll up but when we roll it half way down the cable snaps loose . how do i fix that. It is that cable that makes the window roll down. My caravan is a 2000 dodge grand caravan
Normally when the motor goes, I would always recommend replacing the the entire Power window regulator, the reason being that the plastic rollers break, thus allowing slipping of the cable, thus resulting in you being frustrated not being able to raise/ lower your window. all that being said a new regulator online is about 130.00 (325.00 from dealer + labor). Autopartswarehouse.com (this is where i bought mine) replaced it and have been happy!. you must already know how to get the panel off and get to the motor, with all that there are several steps left, and you will be happy again, remove the three bolts around the regulator, the 4 bolts securing the window tracks and the two clips or bolts securing the window to the window bracket, re assemble and you will be much happier, Good Luck !!!
Posted on Sep 12, 2009
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
durangos have many problems with the windows motors and regulators, I know for personal experience , because I have one, ...when you try rolling the windows down do you hear any noise coming from inside the door..if so.. the cable is busted ..you will need the windows regulator, if no, is probably the motor..you will have to check for power and ground right at the motor connector...if power and ground are present, then you need a motor ....in mine ,I pull the motor and cleaned , and they have been fine for more than a year, I starter with one and them had to do the same to all of them..hope this help
Posted on Aug 02, 2009
This is a vehicle that may have problems with brakes & AC components. Be prepared to pay close to $1000 a year on maintenance.
Posted on Nov 13, 2008
1, Disconnect the able from negative terminal of the battery.
2. Pry the courtesy light from the door trim and disconnect the wire connector..
3. Remove all door trim panel retaining screws and door pull armrest assemblies.
4. Remove the door switch panel and the control switch panel and the control switch assembly.
5. On models with memory seats/mirrors, use small-flat bladed pry tool to remove and disconnect the wire.
6. Grasp the trim panel lift up and pull out to detach it from the door. Disconnect the inner door handle lock rod from the handle. Unplug any electrical connectors remaining and remove the door panel.
7. To install, connect the wire harness connectors and place the panel in position in the door. Press the trim panel down into place until the hooks are seated.
8. Install the armrest/door pulls, the courtesy light and the window switch'
9. Reconnect the battery
Also. You will need star pattern drivers to remove the window and motor from your door. If you have all the equipment it should only take you 1 hour.
Posted on Jan 15, 2009
a lot of pain and heart ache. even on a rack they are a pain . check with your dealer there wae a recall on them for failing its worth the phone call to see kdc744
Posted on Feb 08, 2009
If you have power windows it should be a broken cable, If its manual then it should be the crank asm. or the white plastic trac, it may torn at the end.
Posted on Apr 26, 2009
Tips for a great answer:
Mar 20, 2015 | 2005 Kia Sorento
Sep 03, 2013 | 2007 Chevrolet Impala
Aug 19, 2011 | 2003 Chevrolet Silverado 1500
Jun 17, 2011 | 2002 Ford F350 Super Duty DRW Reg. Cab
Jan 17, 2011 | 2000 Honda Accord
Oct 23, 2010 | 1999 Jeep Grand Cherokee
Jul 16, 2009 | 2001 Mitsubishi Galant
Jul 04, 2009 | 2002 Dodge Durango
Feb 17, 2009 | 2004 Ford Expedition
288 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: