Question about 2000 Buick LeSabre

3 Answers

How to remove headlamp assembly unit on a 2000 buick lesabre?

I have the 2 top bolts removed but there appears to be a side bolt at the very tip of the end with the cornering signal. Can't figure out how to get to that bolt? The only way it looks like to me is to remove the finder liner?

Posted by on

  • alan_william Jun 03, 2009

    I found out it's not a bolt that needs to be removed.It fits into a socket and I had to pull extra hard on it to get it to come out. I then replced the assembly and snapped it back into the socket. So removing the liner was not required. Will this be a no chagre to me?

×

Ad

3 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 87 Answers

Just the 2 bolts is all that is needed, its just pressure. Make sure your bulb is disconnected.

Posted on Jun 03, 2009

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 136 Answers

Yeah once you remove the finder liner you will find the backs of the headlamps... you had it right

Posted on Jun 02, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 477 Answers

Should be able to do it without going into fender liner. Will you have access if corner signal is removed ?

Posted on Jun 02, 2009

  • gord storey
    gord storey Jun 04, 2009

    ajafsu says you had it right , which means I had it wrong. Sorry my , bad

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HOW TO REMOVE A HEADLIGHT FROM A 2007 SATURN OUTLOOK XE


Hi Carol , your going to have to remove the headlamp assembly to replace the bulb !


Remove the headlamp assembly. Refer to Headlamp Replacement.



1



Headlamp Bulb Accessory Covers (Qty: 2)



2



Headlamp Bulb Assembly (High Beam)




Caution: Refer to Halogen Bulb Caution in the Preface section.




Tip

Disconnect the electrical connectors and remove the bulbs.



3



Headlamp Bulb Assembly (Low Beam)


Callout

Component Name

Preliminary Procedure

Remove the front bumper fascia. Refer to Front Bumper Fascia Replacement .




Headlamp Assembly Bolt (Qty: 4)

Notice: Refer to Fastener Notice in the Preface section.

Tighten

6 N?·m (53 lb in)







2





Headlamp Fascia Brace Fender Reinforcement Bolt




Tighten

6 N?·m (53 lb in)







3





Headlamp Cam Adjuster




Procedure

Set the headlamp adjusters at the nominal setting of 6 turns off fully seated.







4





Headlamp Cam Locking Nut







5





Headlamp Assembly




Tip

Disconnect the electrical harness as the headlamp assembly is being removed from the vehicle.

Apr 08, 2015 | 2007 Saturn Outlook XE

1 Answer

Where is the horn located on a 1998 buick skylark


Horn Replacement - Left Side

Removal Procedure


    329494.png
  1. Remove the headlamp assembly.
  2. In order to gain access to the horn assembly, pull the headlamp assembly to one side.
  3. Remove the bolt (3) to the horn bracket through the headlamp cavity.
  4. Disconnect the electrical connector.
  5. Horn Replacement - Right Side

    Removal Procedure


      280047.png
    1. Remove the splash shield from under the fender.
    2. Remove the bolt (3) to horn bracket from under the facia.
    3. Disconnect the electrical connector.

Jan 30, 2015 | 1998 Buick Skylark

3 Answers

How do I replace a headlight assembly on a 2007 Buick Lucerne?


ouch on this buick...
requires a little more work..
1.6 hrs with headlamp alignment.
replace-headlight-assembly-2007-buick#solution-section-eiq04jcqehklpmop1towry5q-4-9.jpg
replace-headlight-assembly-2007-buick#solution-section-eiq04jcqehklpmop1towry5q-4-20.jpg

Nov 12, 2014 | 2007 Buick Lucerne

1 Answer

How to remove headlamp assembly 2006 Ford Five Hundred


bulb replacement?

You may be able to clear bumper cover by pusihing down while pulling out lamp.

Please rate.
---------------------------

SECTION 417-01: Exterior Lighting 2005 Freestyle/Five Hundred/Montego Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 03/14/2005
Headlamp Assembly - Five Hundred, Montego adobe.gif Printable View (211 KB) n0050703.jpg
Item Part Number Description 1 W702706 Top headlamp assembly bolts (2 required) 2 W704551 Side headlamp assembly bolt 3 W702706 Front headlamp assembly bolt 4 13005/13006 Headlamp assembly (RH/LH)
Removal
  1. Remove the front bumper cover. For additional information, refer to Section 501-19.
  1. Remove the 4 bolts and the headlamp assembly.
    • Disconnect the electrical connectors.
Installation
  1. Connect the electrical connectors and position the headlamp assembly in place.
  1. Install the side headlamp assembly bolt.
    • Tighten to 11 Nm (8 lb-ft).
  1. Install the front headlamp assembly bolt.
  1. Install the top outboard headlamp assembly bolt.
  1. Install the top inboard headlamp assembly bolt.
  1. Install the front bumper cover. For additional information, refer to Section 501-19.

Aug 03, 2011 | Ford Five Hundred Cars & Trucks

1 Answer

How to locate and change water pump on 2000 buick lesabre, 6 cylinder engine


I assume you have a 3800 V6 motor in that model car. When standing with the hood open on the passenger side of the car, the water pump is located in the center of the engine. The pulley will have four small (8mm) bolts. To remove: Loosen the 4 bolts on water pump pulley.
Use 13mm socket wrench on tensioner pully to rotate and pull tension off of serpentine drive belt. Take belt off of tensioner and water pump pulleys, bend back out of the way. Finish removing water pump pulley bolts and remove pully. Remove water pump bolts (there are several of 2 different sizes, 10mm and 13mm) . Remove old pump by prying gently around the pump rim to break the gasket's seal, or tap shaft with a rubber hammer. Remove all signs of gasket material on engine mating surface with a scraper and then some fine sandpaper (1000 grit wet/dry) or steel wool. Use high-tack sealant to mate gasket to new water pump, allow to set to a few minutes. Use high-tack again on engine mating surface, allow to set a few minutes, then put water pump to engine using the small bolts tightening them finger tight. Put a small amount of black RTV sealant on larger, long bolt ends about 1/2 " of threads covered. Insert longer/larger bolts and tighten finger tight. Tighten all bolts to firm hand tight using a criss-cross pattern starting in the center top to bottom, then side to side.Do not overtighten, as damage to your new pump or striping thread holes out will result. Allow assembly to set 1/2 hour for sealants to cure. Install pump pulley. Install drive belt. Refill coolant level. Start engine, allow to warm up and check for leaks. Done! :)
Mike

Jun 11, 2011 | 2000 Buick LeSabre

1 Answer

I need to change the headlights


REMOVAL PROCEDURE
  1. Open the hood.
  2. Remove the push-pin retainers that secure the top of the upper fascia and grille assembly to the upper tie bar to allow the upper fascia and grille assembly to flex forward.
  3. Remove the bolt and the push-pin retainer that secures the top of the headlamp assembly to the upper tie bar.

  1. Gently pull the upper fascia and grille assembly forward only far enough to remove the bolt located at the bottom inboard side of the headlamp assembly.
  2. Pull the headlamp assembly straight out to disengage the snap-in retainer at the lower outboard back surface of the assembly. Turn the assembly so that the front inboard corner clears the front fascia.
  3. Pull the headlamp assembly out and away from the vehicle
  4. Disconnect the headlamp electrical connector.
  5. Remove the headlamp assembly from the vehicle.
  6. Remove the headlamp bulb cover from the headlamp assembly.
  7. Remove the headlamp bulb socket from the headlamp assembly.
CAUTION: Refer to Halogen Bulb Caution in Service Precautions.


  1. Remove the headlamp bulb.
  2. Remove the side marker bulb socket from the outer side of the headlamp assembly.
  3. Remove the side marker bulb.
  4. Remove the parking lamp bulb socket from the inner edge of the headlamp assembly.
  5. Remove the parking lamp bulb.
INSTALLATION PROCEDURE

CAUTION: Refer to Halogen Bulb Caution in Service Precautions.


  1. Install the headlamp bulb to the socket.
  2. Install the headlamp bulb socket to the headlamp assembly.
  3. Install the headlamp bulb cover to the headlamp assembly.
  4. Install the side marker bulb to the socket.
  5. Install the side marker bulb socket to the headlamp assembly.
  6. Install the parking lamp bulb to the socket.
  7. Install the parking lamp socket to the headlamp assembly.
  8. Connect the headlamp electrical connector.
  9. Install the headlamp assembly to the vehicle by placing it back into position so that the bolt holes align and the snap-in retainer located at the outboard back surface of the headlamp assembly engages.
  10. Gently pull the upper fascia and grille assembly forward only far enough to install the bolt located at the bottom inboard side of the headlamp assembly.
NOTE: Refer to Fastener Notice in Service Precautions.
  1. Install the bolt and push-pin retainer that secures the top of the headlamp assembly to the upper tie bar.
Tighten the bolts to 6 N.m (53 lb in).


  1. Install the push-pin retainers that secure the top of the upper fascia and grille assembly to the upper tie bar to allow the upper fascia and grille assembly.
  2. Close the hood.
3e4ca4a.gif

Oct 21, 2010 | 2006 Cadillac SRX

1 Answer

How to replace front wheel bearing on 2001 buick lesabre2006 buick lesabre


The bearings on a LeSabre are part of the hub assembly. The hub and bearing will have to be replaced as a unit. To do this you'll need to raise the car, remove the wheel, remove the caliper guide bolts, lift and support the caliper-I use a bent metal clothes hangar to support. Do not loosen the brake line. Slide the brake rotor off the lugs. Disconnect the electrical connector for the antilock brake system. The connector is behind the wheel. Then remove the four bolts holding the hub assembly. The bolts are behind the wheel. Be sure to hold the hub while removing. To install reverse the order. Be sure to check and tighten bolts to specifications when reassembling.

Aug 29, 2010 | 2000 Buick LeSabre

1 Answer

2001 Buick LeSabre. How to remove headlight assembly... Just need to remove and replace the headlight assembly on my 2001 LeSabre Custom. I think it's just a matter of removing a couple of bolts, but would...


the bolts you are looking to remove are located on the top of the light housing. It only takes 2 of them to remove the housing. One is about 6 to 8 inches long, and the other one is much shorter than that. Just unscrew and remove them, and pull the housing straight out.

Jul 19, 2009 | 2001 Buick LeSabre

1 Answer

Replace brakelight in trunk of 300m


REMOVAL
NOTE: Some moisture accumulation inside a vented headlamp unit is normal. Moisture will vent from tubes or vents located on the back of the unit. This normal condition will appear as a fogging on the inside of the headlamp lens (similar to the fog that sometimes appears on the inside of the windshield). This moisture may be removed by activating the headlamps on high beam for 15 minutes.

If water droplets larger than 1 mm in size have accumulated on the inside of the headlamp lens, the headlamp unit should be replaced.


CONCORDE/300M
Release hood latch and open hood.
Disconnect and isolate the battery negative remote cable.
Remove the one bolt retaining the washer bottle filler neck and move aside.
Remove the two bolts retaining the speed control servo and move aside.
Remove fasteners to upper radiator crossmember:
Two jack screws on each side.
Three crossmember retaining bolts on each side.
Three push pin fasteners across top of grille.
Gently pry back grille and remove the two bolts to front crossmember. This will allow you to move the crossmember forward, pivoting at the radiator grille, to access the headlamp unit.
NOTE: Once the crossmember is loose, take care not to scratch the fenders.

Maneuver the headlamp unit to remove from behind fascia. Gentle prying of fascia may be needed to clear it enough to remove the headlamp unit.
Disconnect the lamp connectors and transfer lamps if replacing unit.
INTREPID
Release hood latch and open hood.
Disconnect and isolate the battery negative cable.
Remove jackscrews attaching headlamp to body (Headlamp Housing – Intrepid).
Remove headlamp from body.
Disconnect wire connector from headlamp and parking, side marker, and turn signal lamps.
Remove headlamp housing from vehicle

Mar 26, 2009 | 2002 Chrysler 300M

1 Answer

How to replace front turn light bulb on Caddy SRX 2004?


  1. Open the hood.
  2. Remove the push-pin retainers that secure the top of the upper fascia and grille assembly to the upper tie bar to allow the upper fascia and grille assembly to flex forward.
  3. Remove the bolt and the push-pin retainer that secures the top of the headlamp assembly to the upper tie bar.
    1. Gently pull the upper fascia and grille assembly forward only far enough to remove the bolt located at the bottom inboard side of the headlamp assembly.
    2. Pull the headlamp assembly straight out to disengage the snap-in retainer at the lower outboard back surface of the assembly. Turn the assembly so that the front inboard corner clears the front fascia.
    3. Pull the headlamp assembly out and away from the vehicle
    4. Disconnect the headlamp electrical connector.
    5. Remove the headlamp assembly from the vehicle.
    6. Remove the headlamp bulb cover from the headlamp assembly.
    7. Remove the headlamp bulb socket from the headlamp assembly.
    8. Remove the headlamp bulb.
    9. Remove the side marker bulb socket from the outer side of the headlamp assembly.
    10. Remove the side marker bulb.

Feb 12, 2009 | 2006 Cadillac SRX

Not finding what you are looking for?
2000 Buick LeSabre Logo

Related Topics:

152 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...