Question about 2005 Honda Odyssey

1 Answer

All of my break lights went out at once

All three break lights went out at once. Do I replace a fuse or the brake switch?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Honda Master
  • 22,095 Answers

Remove the switch and check for power ??

Posted on Jun 02, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

04 Hummer H2 break lights and cruise control went out at the same time. I replaced bulbs, fuses, and break light switch. Top break bar still works. Any opinions?


Did you use a test light to check for voltage at the brake fuse circuit. You have two brake fuses. The second one is in ip fuse block, The voltage, for that one, goes hot when you step on the brake.

Feb 24, 2017 | Hummer Cars & Trucks

1 Answer

Brake lights will not work


Use a voltmeter and go from the brake switch which is under the brake pedal and go to a brake light if you have no volts or if you have ok for resistance you have a broken wire check your brake switch first I've found that to be the major weak point

Jul 08, 2014 | 1998 Chevrolet Malibu

1 Answer

I have a 91 ford f150 and the brake lights wont work and the rear right blinker is dim. Can you help me?


Check System Fuse - A fuse is used to protect the brake light circuit from amperage overload. If the fuse has failed it will not allow the electrical current to continue to the brake lights. To check the fuse, first locate the brake light system fuse in the fuse panel which is either under the dash or under the hood in the power distribution center. Connect the test light to a ground like an engine or dash bracket and turn the ignition key to the "on" position. Using the test light probe both sides of the fuse. If the test light illuminates on both sides the fuse is okay continue onto the next step. If one side of the fuse illuminates the fuse has failed and needs to be replaced. If the fuse fails as soon as it is replaced or when you apply the brake pedal the brake light electrical circuit is shorted to ground. Rarely a system short can occur, a car repair manual is needed to find the wiring schematic for the brake light circuit. Once the brake light wiring has been located inspect and repair as needed.

Check Brake Light Bulbs - All cars have three brake light bulbs that create the brake light illumination affect. If all of these brake light bulbs fail no brake light operation will occur. I know what you're thinking, you might say all three brake lights at once? But in reality one brake light went out at a time and you did not notice. People only tend to notice something when they almost run into the back of your car to help persuade them to inform you the brake lights aren't working. Remove any of the brake light bulbs to confirm the bulb is okay or burned. After the bulb has been removed inspect the filament and replace if failed. If the brake light bulbs are okay continue to the next step.

Checking the Brake Light Switch - A control switch is used to connect the brake light electrical circuit. This switch is located near the brake pedal lever. Basic switches have just two wires, power in and power out to the turn signal switch. Use a test light that is grounded and with the key in the "on" position test for power at one side (wire) of the switch, then press the brake pedal while testing the opposite side (wire). It should illuminate the test light, if electrical power is connected through the switch go to the next step. If no power is detected through the switch the brake light switch has failed and replacement is required. If your car is equipped with more than two wires integrated into the brake light switch a car repair manual is needed to locate the proper brake light circuit wiring.

Nov 05, 2011 | 1991 Ford F150

1 Answer

My break lights went out where do i find the fuses for them?


It is not a fuse. It is the brake light switch on the very top of the brake pedal. You have to lay down on your back and reach up in under the dash to replace the switch.

Oct 12, 2010 | 1992 Dodge Stealth

2 Answers

Both break lights went out at the same time. The


the brake pedal has a switch near it with a plunger on it for the brake lights... replace it

Feb 25, 2010 | Chevrolet TrailBlazer Cars & Trucks

1 Answer

Break lights went out at the same time


The brake switch is good it sends power too the three brake lights the same time . so your bulbs are both gone the same time or the sockets are bad or you have a broken wire.
get someone to hold on the brake and test with a test light in the socket, {both ground and live} then check the wires the same way
Hopes this helps you : Bruce Pike

Oct 01, 2009 | 1997 BMW 318

3 Answers

Brake lights do not work All bulbs have been replaced.


Troubleshooting Procedures - Read Completely Before Beginning
(American Car) All Brake Lights Not Working
  • Check System Fuse: A fuse is used to protect the brake light circuit from amperage overload. If the fuse has failed it will not allow the electrical current to continue to the brake lights. To check the fuse, first locate the brake light system fuse in the fuse panel which is either under the dash or under the hood in the power distribution center. Connect the test light to a ground like an engine or dash bracket and turn the ignition key to the "on" position. Using the test light probe both sides of the fuse. If the test light illuminates on both sides the fuse is ok continue onto the next step. If one side of the fuse illuminates the fuse has failed and needs to be replaced. If the fuse fails as soon as it is replaced or when you apply the brake pedal the brake light electrical circuit is shorted to ground. Rarely a system short can occur, a car repair manual is needed to find the wiring schematic for the brake light circuit. Once the brake light wiring has been located inspect and repair as needed.
  • Check Brake Light Bulbs: All cars have three brake light bulbs that create the brake light illumination affect. If all of these brake light bulbs fail no brake light operation will occur. I know what you're thinking, you might say all three brake lights at once? But in reality one brake light went out at a time and you did not notice. People only tend to notice something when they almost run into the back of your car to help persuade them to inform you the brake lights aren't working. Remove any of the brake light bulbs to confirm the bulb is ok or burned. After the bulb has been removed inspect the filament and replace if failed. If the brake light bulbs are ok continue to the next step.
  • Checking the Brake Light Switch: A control switch is used to connect the brake light electrical circuit. This switch is located near the brake pedal lever. Basic switches have just two wires, power in and power out to the turn signal switch. Use a test light that is grounded and with the key in the "on" position test for power at one side (wire) of the switch, then press the brake pedal while testing the opposite side (wire). It should illuminate the test light, if electrical power is connected through the switch go to the next step. If no power is detected through the switch the brake light switch has failed and replacement is required. If your car is equipped with more than two wires integrated into the brake light switch a car repair manual is needed to locate the proper brake light circuit wiring.

Jul 07, 2009 | 2000 Jeep Grand Cherokee

2 Answers

2004 gmc canyon brake issue


brake light switch,replace it
its under the dash at the top of the break peddle takes about 5 min too change

Apr 20, 2009 | 2004 GMC Canyon

1 Answer

My flasher work but brake light not work just roof lighting went aply brake


Chk. fuse, emergency flashers, and middle break light, and the other break lights are on seperate curcit (a fuse for each), if fuse is ok than it could be break light switch, witch is located under dash on steering colume and works off break peddel arm.

Mar 28, 2009 | 1998 Chevrolet Blazer

3 Answers

2000 gmc jimmy brake lights


I had the same problem with my 2001. I found it was the multi function switch. Better known as your turn signal switch. I found that the hazard switch portion of it had shorted. replacement is fairly easy, aftermarket part is available, much cheaper than GM.

Jul 15, 2008 | 2000 GMC Jimmy

Not finding what you are looking for?
2005 Honda Odyssey Logo

119 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...