Question about 1999 Isuzu Rodeo

2 Answers

Obd code 1627 ,1999 4 cylinder isuzu rodeo

I have a problem with this 1627 code,I drive the car and clear the code and the monitors.But once the obd connector is hooked up at the smog shop ,it trips the code and the gas light flashes and the gas gage goes back and forth. I have a problem with this 1627 code,I drive the car and clear the code and the monitors.But once the obd connector is hooked up at the smog shop ,it trips the code and will not pass smog

Posted by on


2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

How do you fix a timing belt on a 1999 rodeo isuzu 4 cylinder?

Posted on Oct 16, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Isuzu Master
  • 80,531 Answers

If P1627 is set when there is a problem with the fuel level sending unit, 100% sure on this problem, replace the fuel level sender in the gas tank, about 2.5 hours, very straight forward job

Posted on Jun 02, 2009


2 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: obd code 1627 ,1999 4 cylinder isuzu rodeo

hprice is right. when you get this code it's usually because the little "fingers" that slide against the metal potentiometer bar on the fuel guage sensor has gone bad or broken off, or in some cases just pushed away from the slider due to it's natural wiggling.

that sensor is located in the fuel pump and you can't really buy a replacement sensor so instead you get the new fuel pump.

I went to 3 yards for this car and almost all the rodeo's of this year had the fuel tanks removed and the fuel pump / sensor pulled. so you can save a hassle and just buy a new pump.

removal is tricky because you've got bolted to the tank the lines that go up, so you have to be careful about removing them. Plus getting that back into the tank is tricky as it has to be exactly straight up / down then the ring clips it down.

It was a long job but had to be done to get past inspection because the check engine light can fail inspections. even if it has nothing to do with smog.

Posted on Dec 14, 2012

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My OBD II & Scan tool gave me a reading ofCode P1299 $10 means on the 2000 Isuzu Rodeo

Try this or look on Yourube for a video

Sep 05, 2017 | Isuzu Cars & Trucks

1 Answer

2001 Isuzu Rodeo 4 cylinder Check Engine Light

Normally a shop would use a scanner to watch the operation of the EGR valve and sensor.
Code 401 means the sensor is telling the computer the flow is not enough. So the problem could be the sensor rather than the EGR valve. And yes one of the ports could be blocked too.

Jun 28, 2013 | 2001 Isuzu Rodeo

1 Answer

P0300 isuzo rodeo 2.2l

PO300 is a OBD II code for a random multiple cylinder misfire detection. Meaning any one or more than one of the engines cylinders is not firing at different times. Any number of malfunctions can cause this.To determine what repairs are needed, i recommend the engine to be diagnosed with a scantool and oscilloscope to monitor the crank sensor signal and other inputs to the computer.
I hope this information is helpful.

Sep 03, 2011 | 2001 Isuzu Rodeo

2 Answers

2000 Isuzu Rodeo, 3.2, 112,000 miles, Service Engine Soon light is on, won't pass inspection till I get it cleared off. Hooked up a scan tool the only code is P1340 and it scan tool says it's a...

well clear code and drive it about 50 to 100 miles to try reset the monters and see if light stay out if so go get it smog so the system that could couse this is a bad wireing harness this may be hard for you to diagnosis this system put if you want me to help you can emaile me and i will send you the hole diagnosis chartDTC P1340 ION Sensing Module Cylinder ID Fault (Cylinder Synchronization Fail)

cant do it here to big

Oct 05, 2009 | 2000 Isuzu Rodeo

2 Answers

99 rodeo check engine light is on.

No...the fuel sending unit is not a computer driven item nor is it monitored in any way by the onboard computer system. Interface with scanner and retrieve code(s) associated with indicator lamp occurrance

Sep 27, 2009 | 1999 Isuzu Rodeo

3 Answers

Obd code 1627 ,1999 4 cylinder isuzu rodeo

p1627: [driver "1" input high voltage]...

I believe the PCM was expecting a signal from a sensor (which one I don't know) that should be low voltage and instead was high voltage and therefore triggered a DTC for that sensor...I will guess a bad O2 sensor...

code may also be cleared by disconnecting battery negative wire for 30 seconds...remember to reset your clock and radio settings...

sorry that is all I can find...please rate me solved

Jun 11, 2008 | 1999 Isuzu Rodeo

Not finding what you are looking for?
1999 Isuzu Rodeo Logo

Related Topics:

737 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts


Level 3 Expert

80531 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14417 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides