Question about 2006 Ford Freestyle

1 Answer

Want to replace front brakes

I want to replace my brakes and am looking for directions I could print out.

Posted by on

  • Jeff Hammack
    Jeff Hammack May 11, 2010

    have you gone to autozone and asked them for a print out from alldata?

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 142 Answers

Go to autozone website. They have repair information on line that may be just what you are looking for.

Posted on Jun 02, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Manual transmission. How do I check the clutch fluid?


Hi, don't know what your vehichle is but the clutch master cylinder is usually found on the bulkhead directly in front of where the driver sits. This is because the clutch pedal linkage to it needs to be as direct as possible. If you cannot find such a thing it may be that you have a cable actuated clutch?

May 25, 2015 | 2011 Volkswagen Jetta

1 Answer

Have a 99 Toyota camry n brake light is on after changing right front brake caliper


Master cylinder fluid piston has entered into a brake safe mode.
when the high pressure brake system is opened in any way, the brake master cylinder piston reaches to the far end of the master cylinder which trips the brake system warning light.

This brake light condition is due to sudden loss of brake fluid pressure on the right front brake caliper assembly during the replacement.

Left rear brake caliper bleed valve will ned to be "opened" until master cylinder piston travels into the opposite direction which "resets" the brake system warning light.

Dot 4 brake fluid recommened for most, but not all vehicles.
Reference vehicle to owners manual for replacement fluid is replaced under master cylinder brake system cap.

Aug 18, 2013 | 1993 Buick Park Avenue

1 Answer

The brake does not work , there are times when it become soft an goes directly to the floor. it does not maintain preasure


If the ABS lights aren't on, then usually it is a normal brake problem.
Could be a faulty master cylinder, might be fautly/leaking wheel cylinders if it has a drum brake rear.
Disk pads might be worn right down and need replacing.
Have someone to pump the brake pedal while you look under the car from the front and rear, look at the inside of both left and right tyres near the bottom. If you see fluid then the brakes are leaking.
The flexible brake lines might be perished and swelling, this will often cause the pedal to go flat to the floor.

Aug 01, 2011 | 2005 GMC Envoy

1 Answer

Front brakes keep locking up i have already this week changed both front calipers brake flex lines the abs light on and stays on what is wrong now


OK, the abs light being on will mean that the ABS (Antilock Braking System) is disabled completely.

That means, that the front wheels will lock up instead of pulsing like normal under a lock up condition at the rate of 5 or 6 pulses a second.

I think that you need to look at broken connections to the wheel speed sensors, or possible replacement of speed sensors after scanning the OBD-II ABS data link with an ABS Brakescan tool such as Actron's ABS Brakescan Tool which is made just for this purpose and sells for around $100 plus shipping off of Amazon.com.

I think that Plain English explanations are available on this tool that will point you in the right direction as to which wheel(s) or circuitry to look at.

Good luck on this repair.

Oct 28, 2010 | 1997 Mercury Sable

1 Answer

How do you put front brake pads on cadillac sedan deville 1996


Front brakes on all modern cars are disc brakes. The front brakes generally provide 80% of the stopping power, and so tend to wear faster than the rear. Replacing them - pads, rotors and calipers - is quite simple once you understand the process, and can save you a great deal of money. These instructions will include a full front brake replacement. Also, having a service manual for your vehicle will save your sanity, as well as time and money. If you only need pads, or pads and rotors, but not calipers, skip the steps for replacing calipers. Repeat the steps below for each side of the car as necessary.
Complete Directions

Jul 24, 2010 | 1996 Cadillac DeVille

2 Answers

Need to replace front disk brakes on my 2002 Lexus Es 300. Do I have to remove the brake line to accomplish this? And what kind of brake fluid should I use? Thanks Robert D in L.A.


No you don't have to remove any lines to replace brake pads. There will be a sticker on top of your fluid reservoir that says what DOT number fluid you need. It could also be stamped into it, or printed directly on it, it's different with different car companies. The higher the number the better the fluid. But use whatever it says because you don't want to mix fluid types, that's always a bad idea.

Nov 09, 2009 | 2002 Lexus ES 300

1 Answer

Front brake will not release all the way -drags . have already replaced caliper.


The brake line may be corroded and isn't allowing the brake fluid to flow back to the caliper. I used to see it on old Volvo's and VW's. Remove the line and test it with compressed air in both directions. Replace the steel lines and flex lines to the front brakes. Don't just do one side.

Aug 21, 2009 | Plymouth Horizon Cars & Trucks

1 Answer

Instructions to change the brakes


look for 2 bolts or pins that go right thru the calipers, they actually retain the pads, normally the heads will be on the back side of the caliper. take them out, there may be thin metal clips (springy) on top of the pads. remove them too. slide out pads working the caliper back and forth to loosen them up. open up fluid resevoir then with a large screwdriver push the brake piston back so as to be able to get new pads it, bolt it all back and your are done.

Mar 21, 2009 | 2001 Ford Escort ZX2

1 Answer

1989 K-1500 Brake Problems


Did you replace your front brake lines as these are rubber and after time collapse causing the truck to pull in the opposite direction! In your case I'd say left front is crimped and blocks fluid and makes right front pull to the right. This is a common problem and one of the first items to replace on these trucks and at $30 cheap insurance.(REPLACE BOTH).

Mar 17, 2009 | 1986 Chevrolet K1500

1 Answer

Front brake replacement on 96 jetta


changing brakes and rotors on the front are pretty simple this is what you do remove the tire unbolt the brake calapor remove brakes from calapor recomress calapor with comressor kit or c clamp then unbolt the center bolt on the rotor by removing the pin then take bolt off and remove roter when replacing with new i recomend you replace font and real barrings and seals then reverse directions and don't for get to bleed your breaks after your doon

Dec 05, 2008 | 1996 Volkswagen Jetta

Not finding what you are looking for?
2006 Ford Freestyle Logo

Related Topics:

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...