Question about 1997 Plymouth Voyager

1 Answer

Power stearing isnt working it is shreaded

If ya power stearing goes bad and is shot how bad of a repair are we talking about?

Posted by on

  • Mike Butler
    Mike Butler May 11, 2010

    Do you know whether it's pump or steering rack?



1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 142 Answers

If it is just the pump, not too awful. need to pull the right front wheel and remove some splash guards on the inner fender well.
Replacing the steering rack is alot more work.
Hope this helps.

Posted on Jun 29, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Want to change Power Stearing Column

It is fairly straight forward except for the electrical that goes through the Column itself.

Be careful, I am assuming you want to change with a TILT?

Why do you want to change it ?

Apr 16, 2013 | 1990 GMC Safari

1 Answer

Put new belt on power steering

On the back side of your poer stearing bow the is a nut you have to loosen. It will take a 15mm wrench . Just loosen it off a couple of turn and th loosen the bolt you see on the top of your bracket. It will drop the power stearing pump down so you can get the belt on. Then tighten the bolt back up and it will tighten the belt. Make sure you have about a quarter inch of play in ya belt after tighting it. Then last but ot least tighten the nut back up and your ready to go.

Dec 02, 2012 | Cars & Trucks

1 Answer

How do you know if your power stearing pump is going bad on a 1998 ford expedition

When the power steering pump is going bad, you will be hearing a humming sound when you turn the steering while on idling and while driving at high speed.

At situations like this no repair can be done. Replacement is the recommended solution when you got a bad power steering pump.

Good luck and rate this.

Dec 08, 2009 | 1998 Ford Expedition

2 Answers

When i step on the breaks the car stearing and the car shakes. whats the problem

If it goes away once you release the brake pedal, it's warped brake rotors.

Nov 02, 2009 | 2002 Mazda 626

1 Answer

Battery flat wont start all lights are on abs,afs,battery,handbrake,plus power stearing light as well jump start car got it running still all lights stayed on thanks

may be that the alternator isnt supplying enough voltage and the system isnt working correctly due to that,put a new battery in dont just jump start not always ideal

Oct 01, 2009 | 2005 Volkswagen Passat

1 Answer


if the rack is leaking then the only option to repair it is to replace it with a remanufactured rack.the noise is probably the power steering pump because it is low on fluid.

Jul 30, 2009 | 2007 Buick Lucerne CXS Sedan

2 Answers

Power stearing problems

this has electronic steering check for a blown fuse!

May 23, 2009 | 2008 Chevrolet Equinox

1 Answer

Powersteering goes out randomly.

have the sensor on the stearing rack checked it may b bad or loose connection

Mar 03, 2009 | 2006 Chevrolet Cobalt

1 Answer

Power stearing pump pully alighnment

Assuming that everything else is OK, first, sight down the belt/pulley arrangement and make sure that everything is aligned correctly. If the pump pulley is not lined up and the pump is a remanufactured unit, it is possible that they pressed the pulley either too far, or not far enough onto the pump shaft. (any machine shop can correct this). If any other pulley is in or out too far, either the component is incorrect or shims are needed to get proper alignment.

Dec 24, 2008 | 1994 Jeep Grand Cherokee

Not finding what you are looking for?
1997 Plymouth Voyager Logo

Related Topics:

98 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts


Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides