Question about 2004 Mazda 3

1 Answer

Tail light Works - Brake light does not

2004 Mazda 3 4 door. I replaced the bulbs on both sides. Only one was actually blown and the other looked fine. I think it might be a fuse but the ones I checked look good. Any ideas?>

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

My break lights work the reverse lights do not. Is it the neutral safty switch/back up-light switch

Posted on Jun 08, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My driver side brake light went out but the tale light still works bulb is new


Hi Jimmy.

Most every circuit in a car goes through a fuse. if you look in your owners manual for the particular vehicle you drive, you should find a listing for a fuse for brake light or brake lights. The tail light being OK should not have anything to do with the brake light. They'll be different bulbs, or, at worst, different filaments in the same bulb, and on different fuses. The brake and tail lights are distinct because otherwise, if you had your tail lights on at night, no one could tell you were pressing your brakes.

If you were meaning that the bulb for the brake light in the tail cluster is good, that also will point to a blown fuse. Check there first.

Good Luck

D

Dec 02, 2015 | Cars & Trucks

1 Answer

Mazda 3 2004 brake light won't come on, turn and hazard work, small trunk light works


Thanks for choosing FixYa and welcome to the site. If your bulb and fuse are good, you probably need to change the brake switch. It is located right above the brake pedal. It is a round looking cylinder. It controls the brake lights. If you have any questions, feel free to ask and thanks for using FixYa.

Apr 07, 2011 | 2004 Mazda 3

2 Answers

Rear brakelights dont come on fuses and bulbs are fine rear window brake light works


If the high level brake light works, then the brake light circuit is fully functional.

Brake light bulbs may LOOK fine, but can still have failed. Often folks don't notice that one bulb has failed until the second one has blown; it's then easy to incorrectly assume that the fault is more complex.

Try replacing the brake light bulbs: if that doesn't work then please report back for additional options.

Sep 24, 2010 | 1999 Audi A4

1 Answer

2004 Chevy Trailblazer Brake Light


I would start by trying another bulb. Even though the brake and tail light share the same bulb they actually are powering different filaments inside of the bulb so you can have a tail light filament that is working fine and illuminating properly but have a burned out brake light element that won't work at all...all inside the same bulb. Not uncommon at all to see this problem and these bulbs are pretty inexpensive.

Jul 26, 2010 | 2004 Chevrolet TrailBlazer

1 Answer

Where is the fuse for the right side tail light?


hi if it is only the one bulb not working/tail light and the front light on same side is working along with number plate and other tail lights may i suggest you replace/check the bulb on defective light as if fuse had blown ? the front light on same side would not be working if you put ignition on and press brake your brake light shoul work ? if so change the bulb as the bulb has two elements inside tail light and a higher wattage element for brake light

Feb 25, 2010 | 2004 Honda Accord

1 Answer

Brake light will not work


check to make sure that you used the exact bulb part number that came out. each bulb has a different resistance.

Apr 08, 2009 | 2001 Dodge Caravan

1 Answer

Mazda 3 tail light on, brake light not on


The bulb actually has two seperate elements in it.
That is why the tail light works fine.

If you take the bulb out you will see the seperate elements.
Change the bulb and it should be fine.

Jan 09, 2009 | 2004 Mazda 3

2 Answers

1997 mazda protoge 1.8 engine


check the actual globe is not blown

Jun 30, 2008 | 1997 Mazda Protege

Not finding what you are looking for?
2004 Mazda 3 Logo

432 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...