Question about 2005 Land Rover LR3

Open Question

Transmission fault: limited gear available

Vehicle not starting.

Posted by on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
pippall
  • 1486 Answers

SOURCE: Transmisson Fault

change the transmission solenoid.

Posted on Jun 03, 2009

Ad
TDISLine
  • 1874 Answers

SOURCE: problemn 1. Gear locked in

1. Now automatic transmission is stucked in "limp home" mode.
2. Even gears are not locked, transmission works in degradation mode.

You must access the Transmission Control Module (TCM) using diagnostic equipment connected to the data link connector of vehicle, in order to pull out all Diagnostic Trouble Codes (DTC) memored. Then you will know if there are bad piece(s), and you will can replace bad piece(s) & repair damages. After that you will be able to erase all DTC from TCM memory, and reset TCM Electronic Control Unit.

Posted on Dec 08, 2010

  • 10 Answers

SOURCE: I have an intermittent fault

It could very well be the gear box. Before I read that part of your question I was leaning that way. It could also be a malfunctioning computer chip. I would find another garage that will diagnose the problem independently. Just tell them the problem don't say you had another garage look at it already. If they have the same result go with the lower bid or ask if they can be the lower bid. If they are different diagnosis you may want a third opinion. Of course this is assuming that each diagnosis is free. Good luck.

Posted on Mar 09, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

LR3 WONT GO INTO REVERSE


read the fault codes to determine the problem area

Mar 21, 2018 | Cars & Trucks

1 Answer

I have a 2009 GMC Acadia. What should the ERS mode be in on a normal basis?


Driver Shift Control (DSC) or Electronic Range Selection (ERS): This position (M-Manual / L-Low) allows the driver to utilize the DSC/ERS system. When the shift selector lever is moved to this position, the driver may select upshifts or downshifts by using the paddle switches located on the steering wheel/shifter. An upshift is requested by pushing either + button. Refer to the vehicle owner's manual for more specific DSC/ERS information.
Driver Shift Control (DSC)/Electronic Range Selection (ERS)
Refer to the owner's manual for specific instructions on DSC. The TCM will override shift commands when maximum engine speed is achieved and will protect from any downshift which may cause excessive engine RPMs.

Electronic Range Select (ERS) Mode
ERS mode allows you to choose the top-gear limit of the transmission and the vehicle's speed while driving down hill or towing a trailer. The vehicle has an electronic shift position indicator within the instrument panel cluster. When using the ERS Mode a number will display next to the L, indicating the current gear that has been selected.
To use this feature:
Move the shift lever to L (Low).
Press the plus/minus button located on the shift lever, to increase or decrease the gear range available.
When you shift from D (Drive) to L (Low), the transmission will shift to a pre-determined lower gear range. The highest gear available for this pre-determined range is displayed next to the L in the DIC. See Driver Information Center (DIC) and DIC Operation and Displays for more information. The number displayed in the DIC is the highest gear that the transmission will be allowed to operate in. This means that all gears below that number are available. For example, when 4 (Fourth) is shown next to the L, 1 (First) through 4 (Fourth) gears are automatically shifted by the vehicle. the transmission will not shift into 5 (Fifth) until the + (Plus) button is used or you shift back into D (Drive).
While in L (Low), the transmission will prevent shifting to a lower gear range if the engine speed is too high. You have a brief period of time to slow the vehicle. If vehicle speed is not reduced within the time allowed, the lower gear range shift will not be completed. You must further slow the vehicle, then press the - (Minus) button to the desired lower gear range.
Automatic Engine Grade braking is not available when the ERS is active. It is available in D (Drive) for both normal and Tow/Haul mode. While using the ERS, cruise control and the tow/haul mode can be used. See Tow/Haul Mode for more information.
© 2017 General Motors Corporation. All rights reserved

Oct 09, 2017 | 2009 GMC Acadia

1 Answer

My BMW 2002 starts out good in morning but when it gets warm or hot my transmission failsafe light comes on what can I do


BMW has been using electronically controlled automatic transmissions in most models since the late '80s. These transmission systems employ a transmission control unit which controls electrical solenoids to manipulate the various control and shift valves and functions in the transmission valve-body. When the transmission control unit detects a problem that it "thinks" could be damaging to the transmission or engine, it goes into a fail-safe or "limp" mode. In this mode, the transmission will function in reverse normally, but in forward it will operate in only one gear (whether you have the shifter in D, or any of the lower gears). This will typically be 3rd or 4th gear, depending on the model. It will start in this gear and stay in this gear with no shifting. You would experience this as sluggish acceleration and higher than normal engine speed at about 40-mph and above.
If you must drive the vehicle when the transmission is in the fail-safe mode, accelerate gently and keep the road speed lower than full highway speed.
Earlier models do not employ fault codes and must be diagnosed manually. Late models do employ fault codes and a diagnostic/scan machine can be used to check and read the faults to assist in diagnostics. Note that this is not your common OBD-II engine management fault code tool. This is what A BMW dealer or a properly equipped independent shop would have for full vehicle system diagnostics and coding operations.

Jun 15, 2017 | BMW Cars & Trucks

1 Answer

My daf xf 480 an error in speed engine, it maximum 2000 rpm, what i have to do?


take it to a DAF service center or have a technician come out to inspect the fault
with limited engine rpms it is possibly in limp mode where the ECM restricts the engine speed and vehicle speed because it has registered a fault that is detrimental to the engine or transmission
LImp mode is only available to allow the vehicle to get to a safe place to stop so that the codes can be read and repairs effected

Jul 03, 2016 | DAF Cars & Trucks

1 Answer

2006 BMW 750 Li My dynamic drive inactive light came on, then a generator fault light came on


BMW has been using electronically controlled automatic transmissions in most models since the late 80s. These transmission systems employ a transmission control unit which controls electrical solenoids to manipulate the various control and shift valves and functions in the transmission valve body. When the transmission control unit detects a problem that it thinks could be damaging to the transmission or engine, it goes into a fail-safe or limp mode. In this mode, the transmission will function in reverse normally, but in forward it will operate in only one gear (whether you have the shifter in D, or any of the lower gears). This will typically be 3rd or 4th gear, depending on the model. It will start in this gear and stay in this gear with no shifting. You would experience this as sluggish acceleration and higher than normal engine speed at about 40 mph and above.

If you must drive the vehicle when the transmission is in the fail safe mode, accelerate gently and keep the road speed lower than full highway speed.

Earlier models do not employ fault codes and must be diagnosed manually. Late models do employ fault codes and a diagnostic/scan machine can be used to check and read the faults to assist in diagnostics. Note that this is not your common OBDII engine management fault code tool. This is what A BMW dealer or a properly equipped independent shop would have for full vehicle system diagnostics and coding operations.

Feb 13, 2015 | 2006 BMW 750Li

1 Answer

What are the problems of a faulty transmission speed sensor in a 2002 land rover discovery 2 v gas?


run the fault codes and look for a faulty torque converter clutch solenoid /servo and a problem TCM unit. A service if not done in the last 60.000 miles would also help.

Dec 16, 2014 | 2002 Land Rover Discovery Series II

1 Answer

2006 crown vic, What are the symptoms of bad transmission range sensor


not shifting --- slow shifting --- missing gear changes --- no OD or reverse or slow shifting to them. Have a pressure test done on the transmission to check for internal damage and have the bands and clutch packs adjusted . Run fault codes if this is available on your vehicle.

Jan 03, 2014 | 1997 Ford Crown Victoria

1 Answer

2007 hyundai sonata limited


This tiptronic is a computer controlled transmission with a computer module for the transmission it holds the transmission in sport mode or regular driving modes if when in first gear there will be now shifts occur your in first just like a manual trans with out a clutch you should be able to shift to other gears in this transmission i.e 2 3 d d2 if not then the module should be checked

May 20, 2013 | 2007 Hyundai Sonata Limited Sedan

1 Answer

Transmission Fault... Limited gears available.


Hi my range rover sport 2006 model can't shift to sport mode please help

May 03, 2012 | 2006 Land Rover Range Rover Sport

1 Answer

Transmisson Fault


change the transmission solenoid.

Jun 03, 2009 | 2005 Land Rover LR3

Not finding what you are looking for?
2005 Land Rover LR3 Logo

Related Topics:

477 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

yadayada
yadayada

Level 3 Expert

80417 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...