Question about 1993 Oldsmobile Cutlass Supreme

1 Answer

Directionals stopped working ~ is this a fuse problem?

I haven't tried the fuse box yet but I think if the directionals don't function at all that it must be a fuse. Does anyone have knowledge of this? Thanks~

Posted by on

  • widfrst Jun 02, 2009

    Will check it out tomorrow but I don't get any response front/back or inside indicators. Will get back tomorrow. Thanks:)

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 111 Answers

Usually a blinker quits when a bulb goes out. As rare as it sounds, I once had bulbs go out on both the left and the right. So I replaced the flasher. But my problem was two bulbs out. The flasher is located under the dash, left side. It's a small can about an inch on a side. I doubt that the problem is a fuse.



Posted on Jun 02, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Sometimes 1 of my directionals stops working, I bought a EP27 flasher, but don't know where it goes, as I have no manual. 2005 Ford Ranger


find the fuse box usually under the dash you will see a round fuse bigger than most that will match the one you bought pull it out and replace with new one :) GL

Jan 04, 2013 | Cars & Trucks

1 Answer

Directionals go on but don't blink


One side doesn't flash or both? Make sur ALL bulbs light up, try emergency flashers. If they work, probablt have a bad flasher relay under driver's side of dash. if not, may have a bad turn signal switch. They are well known for problems.

Oct 02, 2012 | 1995 Chevrolet G20

1 Answer

I am looking for the relay that runs the headlights and heater and directionals


power distribution box under the bonnet ,inside this box near the battery are some alluminium fuses and they do like to corrode on the connections and i think this could be your problem

Jul 09, 2011 | 1999 Volkswagen Passat

1 Answer

When i put on my directionals (blinkers), i hear the sound inside but none of the four directionals work outside, my flashers don't work either. Auto Zone sold me a "flasher" it's a large...


i do not think that part will fix the problem, but look in your owners manual for location of the fuse panels. The flasher unit they sold you will plug into one of them.

Mar 15, 2011 | 1998 Mazda MPV

1 Answer

Left/Right Directionals don't work.


If they light, but don't blink, it's the relay. Check fuse box for round flasher relay. Hit your hazard flasher to make sure you pull out the right one. If you pull the relay and the hazards stop working, they you pulled the wrong one.

Apr 11, 2009 | 2000 Jeep Cherokee

1 Answer

1989 mitsubishi parking (TAIL) LIGHTS not working(running lights)


i would start by looking at the new dashboard switch or there could be a relay under the bonnet hope this helps regards Jim

Mar 28, 2009 | 1989 Mitsubishi Mighty Max Macrocab

1 Answer

2000 ford windstar, directionals both not working, hazards work f


turn signal flasher module or turn signal switch. I usuall try to wiggle teh column switch or move it slowly up and down, back and forth to help determine if it has a bad contact. if i cant get a failure (or turn signal) that way I begin the testing at the base of the column. the flasher module is a common failure on those and isnt unreasonably priced. if i had no diagnostic procedure i would try that first. oh yea, try turning the hazards on and off rapidly several times. the signal goes through the four way switch.

Dec 31, 2008 | 2000 Ford Windstar

Not finding what you are looking for?
1993 Oldsmobile Cutlass Supreme Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...