Question about 2003 GMC Yukon

1 Answer

Need reprogramming instructions for gmc yukon

Worked fine yesterday. today stopped working totally. replaed battery twice and nothing. i was told to reprogram it. how do you do this?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 401 Answers

Hi
dose the other remote work?
check to make sure the battery clip is not broken in the remote
you shouldn't have to reprogram unless you have replaaced the remote

Posted on Jun 02, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 yukon xl turns over fine wont start.


Someone will need to figure out if you are lacking fuel to the injectors or spark to the plugs to proceed.
You say the pump is fine, have you checked the fuel pressure, and do you know if the injectors are getting voltage and ground pulse from the computer ?

Dec 11, 2012 | 2003 GMC Yukon XL

1 Answer

Remote does not work on my 2007 GMC Yukon. I changed battery and I used spare remote, but no response. After I drive the vehicle, the remote will work, but after I few minutes, it goes back to not working.


{: ) Try to reprogram your remote transmitter again. If you have two or more remote transmitters, they should be programmed at the same time (in one session only). Otherwise you may need to replace and reprogram your remote control receiver.

Apr 27, 2011 | 2007 GMC Yukon Denali

1 Answer

Drove Yukon yesterday. Today, no keyless entry, locks, power windows don't work, won't start or turn over. No electrical at all.


You battery is dead. Find another car that has a charged battery and jumper cables. Refer to your owners manual to find out how to jump your vehical.

Apr 17, 2011 | GMC Yukon XL Cars & Trucks

1 Answer

Needing to know why my Yukon's gauges stopped working.


You need to replace cluster, 99-02 Silverado GMC all will work even if it has a trans temp truck is pre wired for it. I put a 02 Denali cluster in my 01 silverado no problems. GM can reprogram hours and odometer if you want.

Mar 10, 2010 | 2000 GMC Yukon

1 Answer

I have a 2003 yukon xl and the front drivers seat is not working properly, the front part of the seat is not working it does not go up and down the rear is fine. you can hear a click when you press the...


I have the identical problem. I was at the dealer today (to have the speedometer replaced under warranty) and they diagnosed the seat as needing a new "lifter unit". Total cost about $1,000.00

:-( :-( :-(

Dec 28, 2009 | 2001 GMC Yukon XL

2 Answers

Replaced the battery in the remote, but still nothing when I go to lock or unlock my door or set off the alarm, nothing happens.


Your remote needs to be "reprogrammed" after battery replacement. Not sure if yours is done in this manner. This is how my remote is reprogrammed on my 1999 Corvette. Stand beside drivers side door, point remote at the car while holding the Lock and Unlock buttons at the same time. Within 10-15 seconds the horn should beep letting you know the reprogramming was successful.

Dec 23, 2009 | 2003 GMC Yukon XL

1 Answer

I just bought a used 2007 Yukon SLT yesterday. I


Hello,
If you armed the security system with the key Fob Transmitter it will stay armed until it is disarmed with the transmitter if the door switch is bad in the latch.
I would try to unlock the doors with your remote transmitter. If this doesnt help try to unlock your rear Trunk/tail gate with the key making sure all doors are closed. If this doesnt work you may need to perform the VTD relearn procedure. Let me know If thats the case Ill give you the instructions you need.

Roy

Nov 15, 2009 | 2007 GMC Yukon

3 Answers

Volume in 2003 yukon denali quit working on radio,


check your manuals guide book on reprogramming the radio and where would you find the fuse for the radio first check the fuse then reprogram if this information has been helpful please let us know good kuck

Jul 28, 2009 | 2006 GMC Sierra Denali

2 Answers

2005 yukon denali, a/c worked fine until battery died


Get the climate control computer relaced or reprogrammed. There is a good chance that when your vehicle was jump started it fried the climate system.

Jul 05, 2009 | 2004 GMC Sierra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

264 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...