Question about 1995 Ford Mustang

2 Answers

Cooling fan cuts off

Hello, I am having problems with the cooling fan in my 95 Mustang. I have replaced the entire fan, the resister, the plug, and the engine coolant temperature sensor. The coolant level is also ok. The fan works fine with the AC on and when the engine heats up. The problem is that it will cut off after maybe 20 minutes and the engine will heat up to a dangerous level. The fan will not come back on unless I let the car cool off for a while. Is there anything I am missing? Thanks. Patrick

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,559 Answers

The fan relay is not functioning correctly or the new sensor is defective.

Posted on Jun 02, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 179 Answers

Make sure your sensor is the right and the wires are not backwards

Posted on Jun 02, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cooling fan inop 1995 mustang gt 5.o


you can check the cooling fan by disconnecting the plug at the motor and run jumper wires from the battery directly to the fan motor it should run if its working if it doesn`t run then the cooling fan motor needs replacing. if it does run then check the plug for a bad connection. other things can cause this like the cooling fan relay, the coolant sensor that sends a signal for the computer to turn on the cooling fan by sending a signal to the relay.

Sep 08, 2014 | Cars & Trucks

1 Answer

Coolant leak under car


I would begin by utilizing our shop's standard cooling system procedure.....
INSPECT COOLANT LEVEL,
TEST SPECIFIC GRAVITY,
****PRESSURE TEST SYSTEM,
****PRESSURE TEST RADIATOR/EXPANSION TANK CAP,
INSPECT DRIVE BELT(s),
****INSPECT COOLANT HOSES,
****INSPECT HEATER HOSES,
****INSPECT BYPASS/MISC. COOLANT HOSES/PIPES,
TEST THERMOSTAT OPERATION,
INSPECT RADIATOR TEMPERATURE,
INSPECT RADIATOR COOLING FAN(s)/CLUTCH OPERATION,
INSPECT CONDENSER/AUXILARY COOLING FAN(s) OPERATION(s)
INSPECT RADIATOR & CONDENSER FOR DEBRI,
OBSERVE COOLANT TEMPERATURE GAUGE OPERATION,

Jan 24, 2014 | Ford Mustang Cars & Trucks

1 Answer

Cooling fan wiring


the cooling fan itself maybe your problem, high resistance due to the motor being internally shorted but not totally gone, sounds like it my let you down shortly, I'd replace the cooling fan motor and burnt connector.

May 31, 2013 | 1999 Ford Escort

1 Answer

Hello im wondering why my truck keeps over heating after iv changed the thermastat 4 times and temp sensor im i also had the intake gaskit changed right befor this started i was pulling out out of the...


CLUTCH ON COOLING FAN FREEWHEELING. COOLING FAN SHOULD HAVE RESISTANCE WHEN TURN WITH HAND WHEN ENGINE HOT.IF NOT FAN FREE WHEEL FAN CLUTCH NEEDS TO BE REPLACED.IF COOLING FAN OKAY.YOU COULD HAVE BLOWN HEAD GASKET.YOUR RADIATOR AND ENGINE BLOCK NEED FLUSHING OUT.CHECK WATER PUMP FOR LEAKING WEEP HOLE IF LEAKING REPLACE WATER PUMP.

Nov 12, 2010 | 1991 GMC K1500

1 Answer

How to change a radiator


1988–91 Models
  1. Disconnect the negative battery cable.
  2. Properly drain the cooling system into a suitable container.
  3. Disconnect the fan motor and motor connector.
  4. Disconnect the upper and lower radiator hoses.
  5. Disconnect and plug the automatic transaxle cooling lines at the radiator, if equipped.
  6. Disconnect the coolant reservoir overflow hose.
  7. Remove the radiator attaching bolts and brackets.
  8. Remove the radiator with the cooling fan attached.
  9. Remove the cooling fan and shroud from the radiator. NOTE: Check all cooling system hoses for any signs of damage, leaks or deterioration and replace if necessary. To install:
  10. Attach the cooling fan and shroud to the radiator and install the assembly.
  11. Attach the radiator bolts and brackets. Tighten the radiator bracket bolts to 7 ft. lbs. (10 Nm).
  12. Connect the coolant reservoir overflow hose.
  13. Connect the automatic transaxle cooling lines to the radiator, if equipped.
  14. Connect the upper and lower radiator hoses.
  15. Connect the fan motor and thermo-switch wire connector.
  16. Refill the system with the proper type and quantity of coolant, check for leaks and bleed the cooling system.
  17. Reconnect the negative battery cable. Fig. 7: Cooling system components — 1988–91 engines 86833085.gif
1992–95 Models
  1. Disconnect the negative battery cable.
  2. Properly drain the cooling system into a suitable container.
  3. Disconnect the fan motor and motor connector.
  4. Disconnect the upper and lower radiator hoses.
  5. Disconnect and plug the automatic transaxle cooling lines at the radiator, if equipped.
  6. Disconnect the coolant reservoir overflow hose.
  7. Remove the radiator attaching bolts and brackets.
  8. Remove the radiator with the cooling fan attached.
  9. Remove the cooling fan and shroud from the radiator. NOTE: Check all cooling system hoses for any signs of damage, leaks or deterioration and replace if necessary. To install:
  10. Attach the cooling fan and shroud to the radiator and install the assembly.
  11. Attach the radiator bolts and brackets. Tighten the radiator bracket bolts to 7 ft. lbs. (10 Nm).
  12. Connect the coolant reservoir overflow hose.
  13. Connect the automatic transaxle cooling lines to the radiator, if equipped.
  14. Connect the upper and lower radiator hoses.
  15. Connect the fan motor and thermo-switch wire connector.
  16. Refill the system with the proper type and quantity of coolant, check for leaks and bleed the cooling system.
  17. Reconnect the negative battery cable. Fig. 8: Cooling system components — 1992–95 engines 86833086.gif
prev.gif next.gif

Aug 27, 2010 | 1991 Honda Civic

1 Answer

Peugeot 406 110 cooling fans not cutting in nor a/c working have changed bitreon sensor


the problem may be with the 2 relays between the cooling fans the plug conectors corrode and damage the relays
recomend you replace connectors and relays

Oct 21, 2009 | 2006 Peugeot 405

1 Answer

I have a 95" model ford aspire. Right now am experiencing a problem on mostly the fuel gauge and the cooling fan. the gauge does not indicate the amount of gas, while the cooling fan does not run. What...


cooling fan has a relay. check it first. Then check the ECT, Engine Coolant Temperature Sensor. It is on the engine and sends a signal to the PCM, Engine Computer.
-----------------------------------------------------------------
Section 03-03: Engine Cooling 1996 Aspire Workshop Manual
DESCRIPTION AND OPERATION Cooling Fan, Electric sty~us~en~file=ani_caut.gif~gen~ref.gif WARNING: WHEN WORKING IN THE ENGINE COMPARTMENT, STAY CLEAR OF THE FAN BLADE. BECAUSE IT IS ELECTRIC AND TEMPERATURE SENSITIVE, IT CAN START AT ANY TIME IF THE IGNITION IS ON.
The electric cooling fan is an electro-drive type. Its operation depends upon engine temperature and ignition switch (11572) position. If engine coolant temperature reaches 97°C (207° F) and the ignition switch is in the ON position, the engine coolant temperature sensor (ECT sensor) (12A648) sends a signal to the powertrain control module (PCM) (12A650) which turns the engine cooling fan motor (8K621) and fan blade assembly on. Because it cannot operate unless the ignition switch is ON, the engine cooling fan motor and fan blade assembly does not operate after engine shutdown. The fan control relay (FC relay) is located in the LH front corner of the engine compartment, between the battery (10655) and the headlamp assembly. Circuit protection is provided by a 30A fuse labeled COOLING FAN in the main fuse junction panel to the left of the battery. If the vehicle is equipped with air conditioning, an additional relay is installed in the circuit. The A/C clutch control relay (19D572) bypasses the engine temperature portion of the circuit. The bypass circuit allows the engine cooling fan motor to operate whenever the A/C switch is engaged.
------------------------------------------------------------------------------------------
11deef4.gif ------------------------------------------------------------------------------------------
Fuel pump/sender access is through cover under rear seat.


Fuel Gauge

  1. Remove the instrument cluster. Refer to the procedure in this section.
  1. Using a jumper, connect the battery positive terminal to the fuel gauge "+" terminal and the battery negative terminal to the fuel gauge "-" terminal.
  1. Connect one lead of a Rotunda Instrument Gauge System Tester 014-R1063 or equivalent to the "F-U" terminal of the fuel gauge (9280), and connect the other lead to the "-" terminal of the fuel gauge.
  1. Adjust the instrument gauge system tester to the resistances shown in the illustration.


    767858e.gif

  1. If the fuel gauge does not operate as specified, replace the fuel gauge. If the fuel gauge is OK, return to the Pinpoint Test.


Fuel Level Sensor

  1. Remove the fuel level sensor (9275). Refer to Section 10-01 for the removal procedure.
  2. Measure the resistance between terminal A and terminal B of the fuel level sensor.

    Connector Shown From Component Side
c0c9791.gif

  1. Adjust the fuel tank float to the following positions:
80cc074.gif



  1. If the resistances are not as specified, replace the fuel level sensor. If the fuel level sensor is OK, return to the Pinpoint Test.
-------------------------------------------
3d2d29a.gif

Mar 27, 2009 | 1995 Ford Aspire

1 Answer

Cooling fan wiring


Was able to locate a fan with the 3 wires. Thank you for your service.
Regards
Russell

Oct 11, 2008 | 1995 Ford Mustang

1 Answer

95 mustang


hi the temp" sender "in this case is a thermostatic switch normaly with 2 connections put an ohm meter across the connections when engine is cold it will show nill or full scale leave meter connected run motor up untill it is hot meter needle should have moved 1 way or the other if it did not the relay is at fault chris merlinv12

Jun 12, 2008 | 1995 Ford Mustang

Not finding what you are looking for?
1995 Ford Mustang Logo

351 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...