Question about 1995 Ford F150 Styleside Regular Cab

2 Answers

Pushing fuel out the filler neck

95 f150 has 2 tanks.front tank stopped workin few days ago,but now its building pressure inside it and pushing fuel back ut the filler neck.what could be the problem.

Posted by on

  • Lorie Lyle Jun 02, 2009

    front tank is full of fuel but truck will not run off that tank.but after several hrs of sitting or driving it builds pressure in front tank and pushes the fuel out of filler neck.rear tank is working fine.

×

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 105 Answers

On the left hand frame rail ahead of the front tank there is a valve that controls which tank the truck runs off of it is bad let me know how you make out
p.s. if you dont wantto replace right away just run the tank that over fills down first and monitor when you switch over to the other one

Posted on Jun 02, 2009

  • smartwrench1 Jun 02, 2009

    if you want to fix with out replacing the valve and the front tank you can get repair ends that fit the uick connects you will need a 5/16 and a 3/8 then go to local hardware store and get compression ends with threads on oppisite end and cap them off. remove front tank and install plugs you can then leave front tank out. you can aslo put flare nuts on the repair ends and flare them and install coupler with plug if you have tool to flare them let me know if you need anything else

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 437 Answers

Was the fuel check valve recall performed on this truck? These are similar symptoms to the recall in which gas would pump from one tank to another.

Posted on Jun 02, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Evap system


The FSM is clear on this. each hose and fitting must be air tight.
or the the car vents gas fumes full time, and the EVAP ECU tests
(monitor) make sure this all works.
you can just look at the left and right side above rear tires. and see
if your hands are small enough to fit here. Id bet not.
some mech, report, the tank can be tilted down at front (drained fuel)
and gain access.
keep in mind, you get fuel siphoning at any time. do not open the system, with fuel in the tank, and then drive to autozone,
i loosen the gas cap so that pressure can not build in tank.
expanding fuel can push fuel out , during a filter change. very
dangerous in a garage, and you gone.
it's just a vent hose, you can see, it and what needs to be done is really obvious. given you arms sides and lenght.
my fsm states, " TANK pull"

Removal & Installation

  1. Relieve the fuel system pressure and disconnect the negative battery cable.
  2. Remove the fuel filler cap from the fuel tank.
  3. Have a Class B fire extinguisher near the work area. Use a hand operated pump device to drain as much fuel through the fuel filler neck as possible.
  4. Use a siphon to remove the remainder of the fuel in the tank by connecting the siphon to the fuel pump outlet fitting.
    CAUTION Never drain or store fuel in an open container because there is the possibility of a fire or an explosion.
  5. Reinstall the fuel filler cap.
  6. Remove the rear seat cushion from vehicle (if so equipped).
  7. Disconnect the fuel pump motor connector and sending unit electrical connectors.
  8. Disconnect the wire harness grommet and harness through the vehicle floor pan.
  9. Raise and safely support the vehicle.
  10. Remove the fuel filler hose clamp from the filler neck assembly.
  11. Remove the fuel breather hose clamp from the filler neck assembly.
  12. Remove the fuel filter inlet hose clamp and hose from the filter.
    NOTE A small amount of fuel may be released after the fuel hose is disconnected. In order to reduce the chance of personal injury, cover the fitting to be disconnected with a shop towel.
  13. Remove the fuel vapor clamp and hose, and fuel return hose clamps and hose from the respective fuel lines.
  14. Using a suitable transaxle jack, support the fuel tank.
  15. Remove the fuel tank retaining bolts and lower the tank.
To install:
  1. Reconnect all fuel hoses, lines and the fuel breather hose to the fuel tank.
  2. Place the fuel tank in its proper space using the transaxle jack, Install the fuel tank retaining bolts.
  3. Remove the transaxle jack.
  4. Reconnect all fuel hoses, lines and the fuel breather hose to the fuel tank.
  5. Install the fuel breather hose and hose clamp to the filler neck assembly.
  6. Install the fuel vapor hose and hose clamps. Install the fuel return hose and hose clamp to the respective fuel lines.
  7. Install the fuel filter inlet hose and hose clamp to the filter.
  8. Lower the vehicle. Install the wire harness and grommet through the vehicle floor pan.
  9. Connect the fuel pump motor and the sending unit connectors.
  10. Install the rear seat cushion. Reconnect the negative battery cable.
"

Mar 26, 2013 | 2002 Suzuki Esteem

1 Answer

I have a 2005 chevy malibu maxx v6. car runs great, no hesitation or stalling, however a intensly strong odor of gasoline suddenly began about 3 wks ago, and is gettin stronger by the day! it Can be...


No service engine light? A loose gas cap will set a light.
You may want to inspect your fuel filler neck and anything close. For a long while its not uncommon for a person to report the fuel odor issue and have it be where some low life cut a filler neck or puntured a tank to steal fuel. But if that were the case there would usually be a service engine or gas cap light as the systems now days monitor pressures so they can detect leaks in the Evap system.

When you mention a smell though under the hood, do you think the smell could be exhaust? I have seen those manifolds crack. or maybe just a leak from a gasket or exhaust donut.

Sep 14, 2011 | Chevrolet Malibu Maxx Cars & Trucks

1 Answer

95 mustang 3.8l standard has a few different problems. 1) the car will shake when it shifts through gears its an automatic sometimes lil sometimes alot. mostly only when shifting about 45mph. 2) the...


I sounds like you have an electrical problem with the dashboard. It will have to be pulled and checked.

I had the same problem with the gas tank on my 95 mustang. You are going to have to drop the tank. There is a rubber seal where the filler neck goes into the gas tank that has failed and must be replaced. You are losing even more gas than you think. Everytime you make a left turn gas is sloshing out through that bad seal.

Dec 29, 2010 | 1995 Ford Mustang

2 Answers

Fix fuel pump


Removal & Installation To Remove:
  1. Properly relieve the fuel system pressure.
  2. Drain the fuel tank through the filler pipe.
  3. Support the fuel tank.
  4. Remove or disconnect the following:
    • Negative battery cable
    • Filler neck
    • Shield and tank straps
    • Fuel lines and vapor hose from pump and tank
    • Electrical connection from fuel pump
    • Fuel tank
    • Fuel pump/sending unit assembly by turning the locking ring (located on top of the fuel tank) counterclockwise using a spanner wrench
    • Fuel pump from the fuel lever sending device
To Install:
  1. Install or connect the following:
    • Fuel pump in tank with new seal around opening
    • Tank and connect fuel lines and vapor hose
    • Tank to the frame
      1. Torque to: 33 ft. lbs. (45 Nm)
    • Shield
    • Fuel filler neck and clamp
    • Negative battery cable
  2. Refill the tank.
  3. Run the engine and check for leaks.
View of the in-tank fuel pump assembly. 7924jg21.gif

prev.gif next.gif

Nov 06, 2010 | 1997 GMC Jimmy

1 Answer

Can fuel pump be put in without dropping the tank.


Removal & Installation To Remove:
  1. Properly relieve the fuel system pressure.
  2. Drain the fuel tank through the filler pipe.
  3. Support the fuel tank.
  4. Remove or disconnect the following:
    • Negative battery cable
    • Filler neck
    • Shield and tank straps
    • Fuel lines and vapor hose from pump and tank
    • Electrical connection from fuel pump
    • Fuel tank
    • Fuel pump/sending unit assembly by turning the locking ring (located on top of the fuel tank) counterclockwise using a spanner wrench
    • Fuel pump from the fuel lever sending device
To Install:
  1. Install or connect the following:
    • Fuel pump in tank with new seal around opening
    • Tank and connect fuel lines and vapor hose
    • Tank to the frame
      1. Torque to: 33 ft. lbs. (45 Nm)
    • Shield
    • Fuel filler neck and clamp
    • Negative battery cable
  2. Refill the tank.
  3. Run the engine and check for leaks.
View of the in-tank fuel pump assembly. 7924jg21.gif

prev.gif next.gif

Oct 09, 2010 | 1999 GMC Jimmy

1 Answer

Instructions on how to remove fuel pump for 95 chevy blazer 4x4


Removal & Installation
To Remove:


  1. Properly relieve the fuel system pressure.
  2. Drain the fuel tank through the filler pipe.
  3. Support the fuel tank.
  4. Remove or disconnect the following:

    • Negative battery cable
    • Filler neck
    • Shield and tank straps
    • Fuel lines and vapor hose from pump and tank
    • Electrical connection from fuel pump
    • Fuel tank
    • Fuel pump/sending unit assembly by turning the locking ring (located on top
      of the fuel tank) counterclockwise using a spanner wrench
    • Fuel pump from the fuel lever sending device

To Install:


  1. Install or connect the following:

    • Fuel pump in tank with new seal around opening
    • Tank and connect fuel lines and vapor hose
    • Tank to the frame

      1. Torque to: 33 ft. lbs. (45 Nm)

    • Shield
    • Fuel filler neck and clamp
    • Negative battery cable

  2. Refill the tank.
  3. Run the engine and check for leaks.






View of the in-tank fuel pump assembly.
7924jg21.gif




prev.gif next.gif

Sep 23, 2010 | Chevrolet Blazer Cars & Trucks

1 Answer

Dodge dakota 2005 -check engine light(gas cap)gas cap was replaced.Fuel spills out when filling tank.Fuel lines were smoked and no clog was found.


There is a check valve in the filler hose to stop fuel from coming out seems yours might be stuck , run a metal coat hangers inside the filler neck while prying open the little fill flap. see if that helps OR you are not or have no VENT to AIR in your evap system causing excessive tank pressure.

Aug 28, 2010 | 2005 Dodge Dakota

1 Answer

How to put hi pressure fuel pump into the engine,it does not have any mark on the pump rotor?


prev.gif next.gif Removal & Installation To Remove:
  1. Properly relieve the fuel system pressure.
  2. Drain the fuel tank through the filler pipe.
  3. Support the fuel tank.
  4. Remove or disconnect the following:
    • Negative battery cable
    • Filler neck
    • Shield and tank straps
    • Fuel lines and vapor hose from pump and tank
    • Electrical connection from fuel pump
    • Fuel tank
    • Fuel pump/sending unit assembly by turning the locking ring (located on top of the fuel tank) counterclockwise using a spanner wrench
    • Fuel pump from the fuel lever sending device
To Install:
  1. Install or connect the following:
    • Fuel pump in tank with new seal around opening
    • Tank and connect fuel lines and vapor hose
    • Tank to the frame
      1. Torque to: 33 ft. lbs. (45 Nm)
    • Shield
    • Fuel filler neck and clamp
    • Negative battery cable
  2. Refill the tank.
  3. Run the engine and check for leaks.
View of the in-tank fuel pump assembly. 7924jg21.gif

prev.gif next.gif

Jul 15, 2010 | 2004 Chevrolet Blazer

1 Answer

Is there a way to change the Fuel Tank Filler Grommet without removing the fuel tank?


take filler neck loose at the fuel door this will give you just enough room . you have to slide the filler neck inside the tank enough to get it out of the fuel door compartment then you can turn it and wiggle an jiggle till you get out

Jun 26, 2010 | 1996 Ford Mustang

1 Answer

I have fuel leaking from the filler neck. Is this


sounds like the fuel tank is building up pressure because of gas expansion. See if the fuel vent line is bent or kinked, if this is o.k change your fuel cap.

Aug 13, 2009 | 1983 Lincoln Mark VI

Not finding what you are looking for?
1995 Ford F150 Styleside Regular Cab Logo

Related Topics:

318 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...