Question about 1992 Chevrolet Camaro

1 Answer

The screen "shield" on my tv broke, i need a replacement part #

Its a 52 inch toshiba model # tp50h15
the only way i can explain this is that there a basically 2 screens. one that the projectors shine on, and an outer one that filters out the glare. the outer one is the one that broke

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,055 Answers

Mine got broke also
i called the local tv repair shop, they had the piece in stock and it was 100.00
it was and easy replacement for me too do it myself!!!!!!!!

Posted on Jun 14, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Gas tank shield fell off


put the car on a hoist and check around and you will find bolts where the shield was fixed. you may be able to reposition the shield and use tex screws net to the existing holes to refix the shield. use care and check for cables on the inside that may be damaged.

Dec 26, 2013 | 2004 Dodge Stratus

1 Answer

Need rear windshield


try and get one from a junk yard.should run you no more then 100.00 and make sure they take it out

Mar 01, 2013 | 1992 Ford Escort 4 Door

1 Answer

Have a 52 inch flat screen, formed vertyical lines,of blue red green yellow orange, white, pink ,and purple.


When and why did this occur, also make and model number are needed to clarify possible causes however it sounds like it's broken beyond economical repair

Apr 06, 2012 | Cars & Trucks

1 Answer

I have a 52 plate ford fusion and i don't know how to change the brake light bulb


please explain what a 52 plate is as i dont live in this third world ethnic majority country that uses codes for the year of a car ,if its basic fusion about 5 yrs old then the light just clips off if i have the right model

Dec 24, 2010 | 2004 Ford Fusion

1 Answer

1988 VW GTI 16 valve.How to fix and replace windshield wiper arm(not just blade). It rotates beyond wind shield.


Remove the wiper arm. Switch on the wipers for a 15 seconds or so then switch them off and allow the wiper motor to reach the "Park" position. Re-fit the wiper arm/blade so the blade sits an inch or 2 from the lower edge of the windscreen. Pour some water on the screen or use the screenwashers and try the wipers to see if they still travel beyond the edge of the screen. Small adjustments can be made by lowering the arm towards the bottom edge of the screen by a couple of splines on the shaft. If it still travels beyond the edge of the screen then you may need a replacement linkage as it could be worn. You may be able to buy the linkage only and use your existing motor-I know this is possible with the Sharan but not sure on your model/year.

Oct 28, 2010 | 1988 Volkswagen GTI

2 Answers

How to pullout starter on 2000 gmc sierra 4 by 4


4.3L Engine
  1. Remove or disconnect the following:

    Negative battery cable Bracket and shield Wires Mounting bolts and shims Starter
To install:
  1. Install or connect the following:

    Starter Mounting bolts and shim. Torque the bolts to 33 ft lbs. (45 Nm). Wires. Torque battery wire nut to 89 inch lbs. (10 Nm) and ignition nut to 18 inch lbs. (2 Nm). Bracket and shield. Torque the nuts to 53 inch lbs. (6 Nm). Negative battery cable

    c5acb83.jpg
    Fig. Exploded view of the starter motor-4.3L engines.


  1. Remove or disconnect the following:

    Negative battery cable Bracket and shield Wires Mounting bolts and shims Starter
To install:
Install or connect the following:

Starter Mounting bolts and shim. Torque the bolts to 33 ft lbs. (45 Nm). Wires. Torque battery wire nut to 89 inch lbs. (10 Nm) and ignition nut to 18 inch lbs. (2 Nm). Bracket and shield. Torque the nuts to 53 inch lbs. (6 Nm). Negative battery cable

a557bbc.jpg
Fig. Exploded view of the starter motor-4.3L engines.

Hope help with this (remember rated and comment this).

Mar 17, 2010 | 2000 GMC Sierra

1 Answer

I have a LG 52 inch model number 52SZ8R-TB but no longer have the manual. There are 3 red LED's on the front panel, the right one flashes red whenever I try to turn the TV on. Does anyone know what this...


YOU CAN REVIEW THE MANUAL FROM THE FOLLOWING LINK.
http://www.lge.com/au/support/product/support-product-profile.jsp?customerModelCode=52SZ8R-TB&initialTab=documents&targetPage=support-product-profile

Dec 11, 2009 | Cars & Trucks

2 Answers

How to Replace the AC filter on my Lexus 01 LX 470


Perform steps 1-3 first to inspect whether you have the access doors or not before ordering filters!!!

Did this little project this evening. Figured I'd write it up.

5 Easy steps:

1. Remove glove box door by removing both screws at the bottom of the door.

2. First pop the the little flap with a fuse/relay out of the black plastic shield in the upper portion of the glove box opening. Next push it back behind the shield through the opening. Next remove the 3 screws holding the shield in place. Don't pull this shield out yet!! Read step 3 first.

3. Gently pull the shield out. Be careful because the glove box light is still plugged into this part. It is located on the right side of the shield. Once it is pulled out slightly, unplug the bulb from the harness and now you can fully remove the part.

4. Now you can see the vertical cover where the air filters reside. The cover is about 5 inches tall and about 1 inch wide. It has 2 tabs on the upper portion of the cover. Squeeze these tabs towards each other and pull the cover off.

5. The filters are now exposed. They are stacked on top of each other. Pull the first filter out then lift the next filter up and pull out. Put new filters back in and reverse the procedure.


Parts needed:
2 Cabin air filters (Toyota PN 88568-60010 if you drop CDan a pm)
1 Phillips screw driver

Time needed:
No more than 15 minutes

STEP BY STEP PHOTO INSTRUCTIONS

5308136.jpg
ce42e62.jpg
75dfbf5.jpg
4d6181d.jpg
c7d7ec9.jpg

Thanks for using FixYa - a FixYa rating is appreciated for taking the time to answer your FERE question.

Mar 19, 2009 | 2001 Lexus LX 470

2 Answers

Changing the starter on my 99 tahoe


Starter Escalade, Suburban, Tahoe, Yukon, Denali, Denali XL, Yukon XL, 1999 – 2005 REMOVAL&INSTALLATION
Removal & Installation
4.8L, 5.3L And 6.0L Engines
CAUTION Before servicing any electrical component, the ignition key must be in the OFF or LOCK position and all electrical loads must be OFF, unless instructed otherwise in these procedures.
  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle.
  3. Remove or disconnect the following:
    • Protective shields, as necessary
    • Starter solenoid shield
    • Starter-to-transmission close out cover bolt
    • Engine oil level sensor connection
    • On 4WD, front axle mounting bracket through bolt nut
  4. Reposition the front axle mounting bracket through bolt until the bolt tip is flush with the support bushing. Do not remove the bolt.
    • Mounting bolts from the engine block. Slide the starter forward until the starter clears the transmission.
    • Starter transmission close out cover
    • Positive battery cable and wiring harness from the starter
    • Starter from the vehicle 0900c152800a6916.jpgStarter removal—4.8L, 5.3L and 6.0L engines
To install:
  1. Install or connect the following:
    • Starter
    • Positive battery cable to the starter. Tighten the nut to 12 ft. lbs. (16 Nm).
    • Starter transmission close out cover
    • Mounting bolts to the engine block and tighten to 37 ft. lbs. (50 Nm)
  2. Reposition the front axle mounting bracket through bolt until the bolt is fully seated.
    • Front axle mounting bracket through bolt nut and tighten to 70 ft. lbs. (95 Nm)
    • Engine oil level sensor connection
    • Starter-to-transmission close out cover bolt
    • Starter solenoid shield
    • Protective shields as necessary
  3. Remove the safety stands.
  4. Lower the vehicle.
  5. Connect the negative battery cable.
5.7L And 7.4L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Mounting bolts and shims
    • Wires
    • Heat shield
    • Starter
To install:
  1. Install or connect the following:
    • Starter
    • Wires. Torque battery wire nut to 89 inch lbs. (10 Nm), and ignition nut to 18 inch lbs. (2 Nm).
    • Heat shield. Torque the bolts to 53 inch lbs. (6 Nm) and the nuts to 35 inch lbs. (3 Nm).
    • Mounting bolts and shim. Torque the bolts to 33 ft lbs. (45 Nm).
    • Negative battery cable
6.5L Engine
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    • Negative battery cables
    • Mounting bolts/nuts and shim, if used
    • Starter
    • Wires
    • Heat shield and bracket 0900c152800a6917.jpgExploded view of the starter motor—6.5L engine
To install:
  1. Install or connect the following:
    • Heat shield and bracket. Torque the bolts to 13 ft lbs. (17 Nm).
    • Wires. Torque battery wire nut to 89 inch lbs. (10 Nm), and ignition nut to 18 inch lbs. (2 Nm).
    • Starter
    • Mounting bolts/nuts and shim, if used. Torque the bolts to 33 ft lbs. (45 Nm) and the nut to 75 inch lbs. (8.5 Nm).
    • Negative battery cables
8.1L Engine
  1. Remove or disconnect the following:
    • Negative battery cable
    • On 4WD, front axle mounting bracket through bolt nut
  2. Reposition the front axle mounting bracket through bolt until the bolt tip is flush with the support bushing. Do not remove the bolt.
    • Positive battery cable nut
    • Positive cable from the solenoid
    • Engine harness ground nut and ground from the solenoid
    • Mounting bolts and starter
    • Heat shield bolts, nut and shield, if necessary
To install:
  1. Install or connect the following:
    • Heat shield, bolts and nut if removed. Tighten the bolts to 35 inch lbs. (3 Nm) and the nut to 44 inch lbs. (5 Nm).
    • Starter and bolts. Tighten to 37 ft. lbs. (50 Nm).
    • Ground wire and nut. Tighten to 30 inch lbs. (3.4 Nm).
    • Positive cable and nut. Tighten to 80 inch lbs. (9 Nm).
  2. Reposition the front axle mounting bracket through bolt until the bolt is fully seated.
    • Front axle mounting bracket through bolt nut and tighten to 70 ft. lbs. (95 Nm)
    • Negative battery cable

Sep 28, 2008 | 1999 Chevrolet Tahoe

1 Answer

Replacing starter 02 silverado 6.6


  1. Remove or disconnect the following:
    • Negative battery cables
    • Right front wheel and fender splash shield, on 6.6L engines
    • Turbocharger exhaust pipe, on 6.6L engines
    • Mounting bolts/nuts and shim, if used
    • Starter
    • Wires
    • Heat shield and bracket 0900c152801cad96.jpgExploded view of the starter motor-6.5L engine shown
To install:
  1. Install or connect the following:
    • Heat shield and bracket. Torque the bolts to 13 ft lbs. (17 Nm).
    • Wires.Torque battery wire nut to 89 inch lbs. (10 Nm), and ignition nut to 18inch lbs. (2 Nm) on 6.5L engines. On 6.6L engines, tighten the solenoidnut to 30 inch lbs. (3.4 Nm) and the positive battery cable nut to 80inch lbs. (9 Nm).
    • Starter
    • Mounting bolts/nuts and shim,if used. Torque the bolts to 33 ft lbs. (45 Nm) and the nut to 75 inchlbs. (8.5 Nm) for 6.5L engines. For 6.6L engines tighten the starterbolts to 58 ft. lbs. (78 Nm).
    • Turbocharger exhaust pipe, on 6.6L engines
    • Right front fender splash shield and wheel, on 6.6L engines
    • Negative battery cables

Jul 30, 2008 | 2002 Chevrolet Silverado

Not finding what you are looking for?
1992 Chevrolet Camaro Logo

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...