Question about 2000 Jeep Grand Cherokee

1 Answer

Adjust handbrake on 2000 model

How do you adjust the hand brake on a 2000 jeep grand cherokee? Cheers.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Jeep Master
  • 3,433 Answers

Adjust the brakes on the rear before making any other adjustments.

Posted on Jun 01, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Toyota 2005 hand brake not working


Is the hand brake really easy to pull??? You may have to adjust your hand brake cable. I found a video on how to adjust the cable.
Hope this is helpful :-)

-Scott Handbrake Adjust Toyota Corolla

Feb 14, 2015 | Toyota Camry Cars & Trucks

1 Answer

Adjust hand brake on astra 2014 model


There is an adjust ment on the rear brakes.
First remove the wheels on the back and then the there is a hole in the brake where you will be able to see wih a flash light a little w?adjusting wheel.
Rotate the adjusting wheel untill it stops the brakes from rotating then slacken the adjuting wheel until the brake starts to turn again.
after that there is an adjustment for the cable either under the handbrake cowling in the cabin or on the cable under the car which is easly to see. Adjust so there are only three clicks before the brake starts to work.
cheers

Oct 31, 2014 | Cars & Trucks

2 Answers

How to adjust handbrake on2001 mondeo


General advice:All handbrakes rise adjust from under the car,very rare behind the handle lever.Worning:Handbrake adjustment need to balance so u need to know if each back wheel brakes even,in order to see that u may have to jack the car and count the rising clicks on handbrake lever to see at what point the wheel stops (u must rotate the wheel by hand (and maybe ask for a friend to brake),with quite some force.Inspect also the interior component (in the back drum if apply,if on disc there is no need)Empiric :by driving at low speed on even road and handbrake hard,the marks of each wheel on the road must start +/- at the same point.Warning:This is dangerous manouver,the car may drift,do not steer while braking,if not shure,better take it to a dino test.Tip:if u tune eack whell at the max brake open position,the handbrake balance,and from there u can adjust the hight of the lever rise by loosing or tighten the cable.Hope u deal it.Cheers.

Oct 24, 2013 | Cars & Trucks

1 Answer

Hi how do you adjust the hand brake on a 2004 jeep cherokee extreme sport


Once you have removed the center console, you should be able to see the base of the hand brake. There should be a bold which you can adjust to tighten or loosen the cable. While at it take time to check for the condition of the cable. Check for wear and have it replaced. Adjustment of the handbrake may work for a while with a damage cable but may break when you least expected.

Apr 03, 2011 | 2001 Jeep Cherokee

1 Answer

Adjusting handbrake


Hi, The hand brake is adjusted under the vehicle, just in front of the rearend. It's a cable that splits into a "Y"; you will be able to see the nut you need to tighten. But be warned that these nuts are usually rusted up real good, so it's a good idea to spray the nut and threaded rod for several days before trying to attempt to make any adjustments. If the threaded rod breaks or the nut stripps out then you have to "replace" the entire hand brake cable assembly.
Take care

Aug 04, 2010 | 1999 Jeep Grand Cherokee

1 Answer

2002 Jeep Grand Cherokee handbrake indicator light on dash does not work. How do I troubleshoot this and repair this?


easy check the switch at the base of the handle it simply grounds the wire to the light bulb when handle is oicked up.so get to the switch and ground the wire. if light comes on then clean/adjust/or replace switch

Mar 23, 2010 | 2002 Jeep Grand Cherokee

1 Answer

The brake lights on my 2000 Jeep Grand Cherokee won't shut off.


The brake light switch is defective or out of adjustment. More than likely located on the brake pedal arm near the top.

Mar 11, 2010 | 2000 Jeep Grand Cherokee

1 Answer

How to adjust handbrake cables.


Under the console, the single cable to the handle joins to an equalizer which connects to the two cables going to the rear brakes. There is no adjustment in that area. The adjustment to the cable doesn't exist. Each rear parking brake is adjusted in drag only.

Jul 20, 2008 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
2000 Jeep Grand Cherokee Logo

Related Topics:

263 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...