Question about 1999 Pontiac Montana

Open Question

Location of crankshaft position sensor on a 1999 pontiac montana

Install crankshaft position sensor

Posted by on

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 701 Answers

SOURCE: location of crankshaft sensor

Hello mitchoreb: My name is Roger and I will be glad to help with your answer. You will need to raise the vevicle in order to see the sensor. Make sure to use safety stands when ubder the vehicle when raised up.Look in the area behind the oil filter.Just in front of the knock sensor.This will be just above the oil pan rail.The knock sensor is a round sensor with a round plug.The crank sensor should hove a oblong plug. You should have a picture along with this reply. Should you need any further help please just ask. Please rate the answer you received as this way we know you recived helpful information. Thank You for using FixYa.Roger8d42463.jpg

Posted on May 09, 2009

Ad
  • 1 Answer

SOURCE: crankshaft position sensor location

if u pull the battery and battery tray u can easily reach this

Posted on Nov 23, 2008

  • 1 Answer

SOURCE: crankshaft position sensor location on 2004 chrystler pacifica

on the engine where is the camshaft position sensor located

Posted on May 17, 2009

polarcycle
  • 1392 Answers

SOURCE: 2004 DODGE STRATUS 2.7L, Location of Crankshaft Position Sensor?

it is located on the right side of the motor, in the trans area. Actually in the bell housing.

Posted on Jun 23, 2009

  • 4 Answers

SOURCE: Crank shaft sensor location.

Underneath on the transmission housing.

Posted on Jul 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

99 stratus 2.5 v-6/no spark.will crank over.


CRANKSHAFT POSITION SENSOR - 2.5L

REMOVAL
  1. Remove speed control servo from driver's side strut tower.
  2. Remove crankshaft position sensor retaining bolt Crankshaft Position Sensor
  3. Pull crankshaft position sensor straight up out of the transaxle housing.
  4. (Disconnect crankshaft position sensor electrical connector from the wiring harness connector.
INSTALLATION - ADJUSTABLE All vehicles will be equipped with an adjustable crankshaft position sensor. This can be identified by an elongated mounting hole in the sensor.
NOTE: If the removed sensor is to be reinstalled, clean off the old spacer on the sensor face. A NEW SPACER must be attached to the sensor face before installation. If the sensor is being replaced, confirm that the paper spacer is attached to the face of the new sensor Crankshaft Position Sensor and Spacer
  1. Install sensor in transaxle and push sensor down until contact is made with the drive plate. While holding the sensor in this position, install and tighten the retaining bolt to 12 N·m (105 in. lbs.) torque.
  2. Connect crankshaft position sensor electrical connector to the wiring harness connector.
  3. Attach connector to heater tube bracket.
  4. Install speed control servo. Tighten nuts to 9 N·m (80 in. lbs.) torque.

May 19, 2012 | 1999 Dodge Stratus

1 Answer

HELP ! Sensor crankshaft position SUZUKI AERIO SX AWD 2.3L 2005.How to replace under the scheme ?


Welcome to FixYa.com
Crankshaft Position (CKP) Sensor Removal and Installation

Removal

1. Remove engine with transmission from vehicle.

2. Remove transmission from engine and then remove flywheel or drive plate from crankshaft.

3. Disconnect connector from crankshaft position sensor.

4. Remove crankshaft position sensor (1) from cylinder block (2).

Installation

Image

Reverse removal procedure noting the following.

- Check to make sure that crankshaft position sensor (1) is free from any metal particles and

damage.

- Apply engine oil to O-ring of sensor.

- Install crankshaft position sensor to cylinder block (2) with specified torque.

Tightening torque

Crankshaft position sensor bolt a: 6 N.m (0.6 kg-m, 4.5 lb-fl)

- Connect connector and fix wire harness with clamp securely. Thank you for Using FixYa.comKind Regards, LeeYour FixYa Expert and Master Technician
leedavidian_133.png

Feb 06, 2011 | 2005 Suzuki Aerio SX

2 Answers

Needs crankshaft position sensor but I cant find it.Where is it and how do I get to it?


Crankshaft Position Sensor Removal & Installation 5.4L & 6.8L Engines To Remove:
Before servicing the vehicle, refer to the precautions in the beginning of this section.
  1. Remove or disconnect the following:
    • Battery ground cable
    • Accessory drive belt
    • A/C compressor electrical connector
    • Position A/C compressor aside
    • Crankshaft position sensor electrical connector
    • Bolt and the sensor
To Install:
  1. Install or connect the following:
    • CKP sensor torque bolt to 89 in. lbs. (10 Nm)
    • Crankshaft position sensor electrical connector
    • A/C compressor and electrical connector
    • Accessory drive belt
    • Battery ground cable
6.0L Engine To Remove:
Before servicing the vehicle, refer to the precautions in the beginning of this section.
  1. Remove or disconnect the following:
    • Battery ground cables.
    • Crankshaft position sensor electrical connector.
    • Bolt and the sensor
To Install:
  1. Install or connect the following:
    • CKP sensor torque bolt to 8 ft. lbs. (11 Nm).
    • Crankshaft position sensor electrical connector.
    • Battery ground cable
prev.gif next.gif

Dec 18, 2010 | 2004 Ford F350

1 Answer

Need to replace the crankshaft position sensor


REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable.
  2. Remove the serpentine drive belt from the crankshaft pulley.
  3. Raise and safely support the vehicle.
  4. Remove the right front wheel and tire assembly and the right inner fender access cover/splash shield.
  5. Using a 28mm socket, remove the crankshaft harmonic balancer retaining bolt.
  6. Remove the crankshaft balancer, using a puller if necessary.
  7. For 1992-99 vehicles, remove the CKP sensor shield. Fig. 1: If so equipped, remove the crankshaft position sensor shield 89634g95.gif

  8. Unplug the sensor electrical connector.
  9. For 1987-91 vehicles, perform the following:
    1. Remove the sensor and pedestal from the block face.
    2. Remove the sensor from the pedestal.
  10. For 1992-99 vehicles, remove the sensor from the block face. To install:
    1. For 1987-91 vehicles, perform the following:
    2. Loosely install the crankshaft sensor on the pedestal.
    3. Position the sensor, with the pedestal attached, on crankshaft sensor installation tool J 37089 or equivalent.
    4. Install the bolt to hold the pedestal to the block face, then tighten to 14-28 ft. lbs. (20-40 Nm). Fig. 2: Position the crankshaft sensor tool on the crankshaft 89634g76.gif
      Fig. 3: Insert the crankshaft sensor tool into the harmonic balancer 89634g75.gif

    5. Tighten the pedestal pinch bolt to 30-35 inch lbs. (3-4 Nm).
    6. Remove the special tool.
    7. Place the crankshaft sensor tool on the crankshaft balancer and turn. If any vane on the harmonic balancer touches the tool, replace the balancer.
  11. For 1992-99 vehicles, install the CKP sensor on the block.
    1. Install the retaining bolts and tighten to 14-28 ft. lbs. (20-40 Nm).
    2. Install the crankshaft position sensor shield.
    3. Attach the sensor electrical connector.
  12. Install the balancer on the crankshaft.
  13. Tighten the crankshaft bolt to 200-239 ft. lbs. (270-325 Nm) for 1987-91 vehicles. For 1992-99 vehicles, tighten to 110 ft. lbs. (150 Nm), plus an additional 76°rotation.
  14. Install the inner fender shield and the right tire and wheel assembly.
  15. Carefully lower the vehicle.
  16. Install the serpentine belt.
  17. Connect the negative battery cable.
prev.gif next.gif

Oct 29, 2010 | 1999 Oldsmobile 88

2 Answers

I need to put a crankshaft sensor but I don't Know its location I already changed the cam sensor. Ronnie


The crank sensor is located on the engine near the flywheel axis of the crankshaft.

Crankshaft Position Sensor Removal & Installation To Remove:
Location of the crankshaft position sensor on the 2.4L engine 90904g51.gif
Location of the crankshaft position sensor on the 3.0L engine 91154g20.gif
Location of the crankshaft position sensor on the 3.3L and 3.8L engines 91154g21.gif
NOTE: On the 2.4L engine, the crankshaft position sensor is mounted to the engine block behind the alternator, just above the oil filter. On the 3.0L, 3.3L and 3.8L engines, the crankshaft position sensor is mounted on the transaxle housing, above the vehicle speed sensor.
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle.
  3. Disconnect the crankshaft position sensor electrical connector.
  4. Unfasten the sensor mounting screw, then remove the sensor from the vehicle by pulling it straight out.
To Install:
NOTE: If the sensor removed is going to be re-installed, clean off the old spacer on the sensor face. A new spacer must be attached to the sensor face before installation. If the sensor is being replaced, be sure that a paper spacer is attached to the sensor face.
  1. Install sensor and push the sensor in until contact is made. While holding the sensor in this position, install and tighten the mounting bolt to 105 in. lbs. (12 Nm).
  2. Connect the crankshaft position sensor electrical connector.
  3. Lower the vehicle.
  4. Connect the negative battery cable.
prev.gif next.gif

Jul 31, 2010 | 1996 Plymouth Grand Voyager

1 Answer

Where is the crankshaft sensor on a v6 2000 chrystler sebring


CRANKSHAFT POSITION SENSOR - 2.5L
REMOVAL
Remove speed control servo from driver's side strut tower.
Remove crankshaft position sensor retaining bolt Crankshaft Position Sensor
Pull crankshaft position sensor straight up out of the transaxle housing.
(Disconnect crankshaft position sensor electrical connector from the wiring harness connector.
INSTALLATION - ADJUSTABLE
All vehicles will be equipped with an adjustable crankshaft position sensor. This can be identified by an elongated mounting hole in the sensor.

NOTE: If the removed sensor is to be reinstalled, clean off the old spacer on the sensor face. A NEW SPACER must be attached to the sensor face before installation. If the sensor is being replaced, confirm that the paper spacer is attached to the face of the new sensor Crankshaft Position Sensor and Spacer

Install sensor in transaxle and push sensor down until contact is made with the drive plate. While holding the sensor in this position, install and tighten the retaining bolt to 12 N·m (105 in. lbs.) torque.
Connect crankshaft position sensor electrical connector to the wiring harness connector.
Attach connector to heater tube bracket.
Install speed control servo. Tighten nuts to 9 N·m (80 in. lbs.) torque.

May 22, 2010 | 1998 Chrysler Sebring

1 Answer

How do i install a crank angle sensor on my ford 1997E250 4.2L V6


FREE FROM ME TO YOU!!! I HOPE THIS HELPS YOU!! Sensor, Crankshaft Position (CKP) Removal
  1. Raise and support the vehicle.
  1. Remove crankshaft position sensor (CKP sensor) (6C315).
    1. Disconnect the CKP sensor electrical connector.
    1. Remove the (A) CKP sensor shield nuts and the (B) CKP sensor shield.
    1. Remove the (C) CKP sensor bolts and the (D) CKP sensor.

fc50791.gif Installation
  1. Install crankshaft position sensor.
    1. Position the CKP sensor.
    1. Install the bolts.
    1. Position the shield.
    1. Install the shield nuts.
    1. Connect the electrical connector.

cad91ff.gif

Mar 25, 2010 | 2002 Ford E250

1 Answer

Crankshaft sensor on a Monte Carlo 2001 SS 3.8 where is this on the car and how to replace it?


3.8L Engine
  1. Turn OFF the ignition.
  2. Remove the serpentine belts from the crankshaft pulley.
  3. Raise the vehicle.
  4. Remove the right front wheel and tire assembly.
  5. Remove the right inner fender access cover.
  6. Hold the flywheel with a (J 37096) flywheel holding tool.
  7. Using 28 mm socket, remove the crankshaft harmonic balancer retaining bolt.
  8. Remove the crankshaft harmonic balancer, using a (J 38197-A) balancer remover.
  9. Remove the crankshaft position sensor shield (1). Do not use a pry bar.
  10. Disconnect the sensor electrical connector.
  11. Remove the attaching bolts from the crankshaft position sensor.
  12. Remove the crankshaft position sensor from the block face.
To install:
  1. Position the crankshaft position (CKP) sensor to the block.
  2. Install the bolts to hold the CKP sensor to the block face. Tighten the bolts to 14-28 ft. lbs. (20-40 Nm).
  3. Reinstall the crankshaft position sensor shield.
  4. Connect the CKP sensor electrical connector.
  5. Position the crankshaft harmonic balancer on the crankshaft.
  6. Hold the flywheel with a (J 37096) flywheel holding tool.
  7. Using a (J 36660-A) torque/angle meter, tighten the harmonic balancer bolt to 110 ft. lbs. (150 Nm), plus an additional 76 degrees.
  8. Install the right inner fender access cover.
  9. Install the right front wheel and tire assembly.
  10. Tighten the wheel nuts to 104 ft. lbs. (140 Nm.).
  11. Lower the vehicle.
  12. Reinstall the serpentine belts.

It looks like this:

fd368a5.jpg

Jan 10, 2010 | 2001 Chevrolet Monte Carlo

1 Answer

04 Dodge SRT 4 crankshaft sensor


The Crankshaft Position Sensor is located directly next to the starter.
  1. On 2.4L SRT-4 remove the lower inner cooler hose from the metal tube.
  2. Remove the Structural Collar
  3. Unlock and disconnect the electrical connector to the crankshaft position sensor.
  4. Remove the crankshaft position sensor bolt.
  5. Remove the sensor
Reverse Order to install except note that:

Use a twisting motion when installing the sensor.

Install and tighten the crankshaft position sensor bolt and tighten to 9 N·m (80 ±15 in. lbs.).

Aug 15, 2008 | 2004 Dodge SRT-4

Not finding what you are looking for?
1999 Pontiac Montana Logo

Related Topics:

2,267 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

79851 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...