Question about 2006 Dodge Ram 2500

1 Answer

2006 dodge ram diesel a/c quit comprssor clutch wont start any help is appreciated Just took my '06 2500 in becuase the 4WD switch got stuck. Towed a 15000# 5th wheel 2 hours without being able to go 40mph. At the exact same time the A/C stopped blowing cold air. Dodge said the compressor was out for a mere $825.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I have the same truck with the same exact problem. Mine also stopped blowing while pulling a camper and indeed it is the clutch on the A/C. I was told if you can find someone in your area that can actually rebuild the compressor and not put a new one in you can come out alot cheaper! Also if you crank your truck and turn the A/C on look under the truck on the passenger side at the compressor and take a tool of small hammer and tap the compressor in the middle and it should come on and run the a/c for a little while! I did this until it finally went out and it worked! Might buy you some time!

Posted on Jun 02, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2006 Dodge Ram Diesel AC will not work, found code P1274


P1274-a/c Clutch Control Circuit 2 Open You will need the help of the dealer or a factory wiring diagram and diagnostic flow chart to fix this one. I can't find a clear cut answer other than someone that used a fuse for the AC circuit to power another system and the fuse blew out.

Jul 24, 2012 | 2006 Dodge Ram 3500 Truck

1 Answer

AC stopped cooling on my 2007 ram 2500 diesel. Had it recharged but still did not work. I have power at switch. The clutch is not engaging. Can I replace just the clutch.?


no you hve to change your car compressor! because your car compressor is not working properly! or your compressor coil may be short! vote me if it is helpful for you

Sep 18, 2011 | 2006 Dodge Ram 2500

1 Answer

I have a 06 dodge ram 3500 with Cummings diesel.


you have what is known as an open diff. or worn out clutch packs in a limited slip. most makers put in a open diff because its cheaper and handles better. if you did not pay for it on your invoice your stuck with stock unless you put it in your self.

Dec 23, 2009 | 2006 Dodge Ram 2500

1 Answer

Starting problem


check for fault codes in both engine controllers..may have a camshaft or crankshaft position sensor fault

May 10, 2009 | 1999 Dodge Ram 2500 4WD

2 Answers

99 ram diesel wont start


Did you check to see if there is power to the glow plugs if not then that may be the problem and if there is power when you cycle the key not to start but for the plugs to warm up you may have a bad glow plugs.

Apr 22, 2009 | 1999 Dodge Ram 2500 4WD

1 Answer

Clutch position sensor on dodge 2500


Jim, I have the same problem. Looking in my Chilton's manual doesn't help much. But, if you look at the firewall from the driver's seat, where the clutch master cylinder rod goes through the firewall, you will see a plastic cylinder around the rod. There should be a wire that goes from that plastic cylinder and connects into a wiring harness. The manual says that if you separate the clutch position sensor wire from the wiring harness, and jumper the two contacts at that connection in the wiring harness, you will bypass the clutch position sensor switch. I have not yet done this but it is the recommended method of debugging starting problems. If you continue to have problems, I can email to you the section of the Chilton's manual for evaluating the starting system. At least I think I can get my computer to copy this section of the manual. The manual does not give the location of the clutch position sensor but that is the only location i can find that meets the description. I have a 1999 Ram 3500 4WD diesel quad cab.

David Wagner davidwagnerpe@comcast.net

Nov 20, 2008 | 1999 Dodge Ram 2500 4WD

1 Answer

2004 Dodge 2500 Diesel Not Starting


should be a switch on the clutch pedal check and see if it is still plugged in

Sep 23, 2008 | 2004 Dodge Ram 2500

1 Answer

1998 dodge 1500 wont shift


first of all standard or auto i am guessing its standed standard under drivers side hood near master cylinder there is a small clutch reservoir if there isnt enough fluid it wont extend the throw out bearing far enough for a shift because the clutch pedal is hitting the floor not enough fluid to extend the slave cylinder to drive the fork second faulty slave cylinder or throw out bearing as far as the light blown dash bulb or somone snipped the wire or took the bulb out

Sep 11, 2008 | 1998 Dodge Ram 1500 4WD

Not finding what you are looking for?
Cars & Trucks Logo

1,097 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...