Windshield Washer Pump does not operate on 02 Accent
My washer pump does not work on my 02 Accent as well. I checked the fuse panel under the dash, fuse was ok. I checked the box under the hood, everything was ok, can anyone tell me what the 3 wires that go into the plug for the washer pump are? I know one is orange, one is brown, and one is blue with orange or brown stripe, and the after market pump I bought only comes with 2 wires, none match the colors of factory wiring. Any help would be great!
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need. Goodluck!
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
There are two relay's in the under hood fuse / relay box . Wiper relay an wiper relay 2 . Maybe one is bad . also check fuse #14 25 amp. Wiper fuse.Plus the BCM - body control module has a hand in making the wipers work . Are you familiar with automotive electronic control modules ?
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Body control module (BCM)
• Wiper micro relay
• Wiper 2 relay
• Wiper diode
• Windshield wiper motor
• Windshield washer pump
• Windshield washer nozzles
• Windshield washer solvent container
• Windshield wiper arm and blade assemblies
• Windshield wiper transmission
• WIP/WASH 10A fuse
• WIPER 25A fuse
Wiper/Washer System Description
The body control module (BCM) controls wiper motor low speed operation. The washer pump and high speed operation are controlled directly by the wiper/washer switch. The windshield wiper/washer switch supplies voltage on the signal circuits to the BCM for windshield wiper/washer operation. When WASH, MIST, DELAY, LOW, or HIGH is detected, the BCM energizes the wiper micro relay by suppling voltage to the relay coil. This allows battery voltage from the WIPER fuse to flow through the relay switched input then through the contacts and out the relay switched output to the wiper 2 relay switch contacts. Since the wiper 2 relay switch contacts are normally closed to the low speed circuit of the windshield wiper motor, the motor will operate at low speed.
Sep 9, 2012 - Uploaded by RatchetsAnd Wrenches
Here is a step by step guide to diagnose any trouble with yourwindshield washer pump, or other issues that ...
Look in the fuse panel to visibly check for blown fuse. Each manufacturer hides the fuses in a different place - sometimes under the dash panel, sometimes behind an ash tray or change compartment, sometimes in the glove box. The panel should have a fuse layout diagram with the rated amps for each use - usually 10, 15, 20 or 30. When you find the blown fuse replace with a new one of the same amp rating - too low and it will blow. Too high and you could damage the wiring if there's a short. Before I went crazy tracing fuses, check the plug on the washer motor. I would unplug it, clean the contacts with a spray cleaner and replace.
Or maybe the pump motor has gone bad. Electronics Goldmine sells washer pump motors very cheaply. One of them may fit.
no the front is not in power with rear they are seperate. check wire plug (connector) at pump,( i assume pump is mounted on or in reservoir ) with test light for power while a helper depresses the spray switch. check for a blown fuse, check switch, check wiring
Check power at the pump motors. You may not see a fuse because some run off a circuit breaker. If all else fails, a bit "backyard" but you likely could break out the washer pumps from the system and make a simple push button on the dash to operate them.