Question about 1997 Chevrolet Tahoe

1 Answer

Installation instructions I have a 1997 Chevy Tahoe and I need to install OEM runnning boards but I don't know where that they can mount to. I'm being told that there is a spot on all the Chevy Tahoes from 1994 to 2000 with a factory install spot. Don't see it!

Posted by on

  • yadayada
    yadayada May 11, 2010

    have no idea on this one, what do the instructions say?

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 181 Answers

Correct, there are factory install holes/spots on the frames as the run along the side of the Tahoe under the door locations. If they had not been used they may appear only as holes in the from that the running board hardware will mount into. They are preinstalled so that you do not need to drill any new holes in the frame itself.

If all else fails, head on over to your nearest use car dealer and peek underneath an existing Tahoe. Some Chevy dealers may also have similar vehicles on their lots. Best of all there's no charge for peeking.

Posted on Jun 01, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to know how to install caralarm


the best action to take is to follow instructions from the package.
you need power wire attache to positive batt, and negative to any part of chassis. then attach bumb sensor and fuses.

Nov 23, 2016 | 1997 Chevrolet Tahoe

2 Answers

I have a 1997 chevy tahoe 2-door.I need to know where the fuel pump fuse is located. I already checked the relay box and the fuse box on the dash board.The relay is working.I dont no if it could be labled...


If you have already checked the relay and fuse then have someone bang on the fuel tank hard while you crank the engine, if it starts then you know you have a bad fuel pump.

Sep 19, 2011 | 1997 Chevrolet Tahoe

1 Answer

SERPINTENE BELT Installation 1997 Tahoe


Here is the serpentine belt diagram for a 1996-1998 Chevy truck with the 4.3, 5.0 and 5.7 liter engine. Removing the belt is very simple. Using breaker bar and a socket that fits the center bolt of the tensioner pulley

Hope this helps...crew_dawg_5.jpg

Aug 28, 2011 | 1997 Chevrolet Tahoe

1 Answer

I have a 1997 chevy tahoe and put a 2005 chevy tahoe motor in and my gas mileage is only 8 to 10 miles per gallon, why?


As these are two different motors with different type control systems involved, did you mean that you installed a replacement motor that was remanufactured or purchased new in 2005?

Apr 17, 2011 | 1997 Chevrolet Tahoe

2 Answers

Will a 1990 chevy 1500 truck 4x4 transmission fit in a 1997 4x4 chevy tahoe


yes it will as long as it is the same model transmission. As long as you get a transmission out of a standard cab truck you should be ok. ( for a good idea Most 88-98 gm trucks, full size blazers,jimmys,tahoes, and yukons will interchange) same chassis just different bodys and emblems

Feb 27, 2011 | Chevrolet Tahoe Cars & Trucks

1 Answer

Removal procedure of oil pan for a 1997 chevy


To remove the engine oil pan either the engine has to be lifted all the way off of the motor mounts and the oil pan should just clear the flex-plate and transmission, or the front axle dropped down out of the way, or the transmission and flex-plate will have to be removed.

Usually if the engine can be lifted enough to fit a piece of 2x4 wood between the motor mounts and the frame then the oil pan will usually just have enough clearance to be removed from the rear and the oil pan should just clear the transmission and the flex-plate. Also, be sure to check that the fan blade does not damage the fan shroud when lifting the engine.

Let me know if you require any further assistance.

Jul 26, 2010 | 1997 Chevrolet Tahoe

1 Answer

How do you install a heater fan on 97 chevy tahoe


un -swrech the one in the tahoe passgern side floor board look up and you'll see it

Feb 12, 2010 | 1997 Chevrolet Tahoe

1 Answer

How can I repair the melted part of the board where the fuel pump relay plugs into. There is only one melted area for one of the prongs on the relay 1997 Chevy Truck The relay over heats and then stops...


One solution is to get a "universal" relay block (connector) and wire it to the fuel pump wires on the back of the existing relay block. You can mount them virtually anywhere you want. These are readily available at most parts stores. They sell them for people that want to add flood and/or headlamps to their 4X4's.

Another solution is to get an OEM relay block out of the salvage yard.

Oct 31, 2009 | 1997 Chevrolet C1500

2 Answers

I need to know how to change the fuel pump on a 1997 chevy tahoe


to remove the fuel pump you mus lower the fuel tank there ae two bolts on the back of the tank spray with wd 40 and use deep well socket 9/16 or 5/8 socket first lossen fuel hose clamp and over fill tube then unscrew the two bolts holding tank to vechicle, use a floor jack and a piece of plywood to lower the tank downone you have the tank on the ground tap the lock ring counter clockwise the tubes and wires come out of the center of the lock ring, tap it with a old wood chisel on two oppiste sides to get it to move once the ring is lose lift the fuel pump amd fuel sending unit out of the tank, replace fuel sock and o-ring on tank lube the o ring before installation and install in reverse proceedure replace main fuel filter, pull tank out and make sure there is no **** in the tank clen if there is. check the pickup tube for cracks. and put it back together and your set to go.

May 20, 2009 | 1997 Chevrolet Tahoe

2 Answers

1997 chevy tahoe 4 wheel drive transmission


Needs rebuilt converter is bad, a progressive problem that caused overheating most likely. www.TransmissionGarage.com

Jul 14, 2008 | 1997 Chevrolet Tahoe

Not finding what you are looking for?
1997 Chevrolet Tahoe Logo

Related Topics:

122 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...