Question about 1995 Toyota Camry

1 Answer

When ignition turned, just get a click. All other electrical works, radio, power windows, etc. I think it's probably the starter.

Where is the starter located?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

YOUR STARTER MOTOR HAS GONE MATE TRY BUMP STARTING IT BET IT GOES,TRY TAPPIN YOUR STARTER MOTOR WAE A HAMMER IF NO GOOD GO GET ONE FOR A FIVER AT A SCRAPPY.

Posted on Jun 01, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Will not start clicking noise


could be your starter's solenoid.Best to replace starter

Dec 06, 2013 | Chevrolet Equinox Cars & Trucks

1 Answer

Trunk release, power windows, turn signals, wipers, radio all stopped working at the same time on 86 chrysler fifth ave


Hi! This doesn't sound like a shorted wire, because a short would usually blow a fuse. Since you're having trouble with the starter, I'm thinking that the ignition switch needs replacement. Depending on the year/make/model, you may be able to change just the electrical part of the ignition switch.

Oct 28, 2013 | 1986 Chrysler Fifth Avenue

1 Answer

99 Denali wiring from BCM


The BCM seems to be the source of some of the problems you mention. The red wire connected to terminal F is the power source. The BRN wire connected to terminal D supplies power to the ignition switch. The DK BLU wire connected to terminal C supplies power to the wiper and radio fuses and the power window circuit breaker which probably is the source of the clicking sound in the instrument panel fuse block. Normally, with the ignition switch in START or RUN position power is applied through GAUGES fuse 4 to the instruments (not dash lights) in the cluster. I believe replacement of the BCM will solve most of the problems you describe

Oct 30, 2012 | 1999 GMC Yukon Denali

1 Answer

My 2000 Toyota tundra will not start, i replaced fuse's and got to the starter i was able to get the starter to turn and my readings read it was fine, i clean my battery post's and cables but still...


make sure your getting power to wire on starter as you turn the key to start position if not ignition switch could be faulty if you are getting power to starter coud be your starting motor

Sep 16, 2011 | Toyota Pickup Cars & Trucks

3 Answers

1996 GMC JIMMY WILL NOT START: Turn the ignition and there is a repeated clicking sound. The interior lights, radio and power windows still function. Replaced the "in line" fuel filter under the...


It sounds like you probably have a shorted battery cell. This will not only cause the repeated clicking that you described, but it will also rob power when jump-starting from another vehicle. There is probably enough power when jump starting to turn the starter over, but after the starter take the power that it needs, there is not enough power to operate the computer system....so I have no doubt that you probably are not getting any fuel. The computer has to tell the fuel pump to run. If there is no power for the computer....I think you can figure it out from here.

Replace the battery and try it again.

Please also review this article: My Car Won't Turn Over

Aug 12, 2011 | GMC Jimmy Cars & Trucks

1 Answer

1998 subaru clicks when starting


The starter solenoid is clicking so your ignition switch is okay. You've changed the starter? Apparently the solenoid is separate from the starter. Check that the wire from the solenoid to the starter is intact and make sure the ends are nice and shiny. Then it's probably the solenoid itself. Some cars have a fused wire, notably older Fords where the wire itself is a fuse. Your "Snubaru" dealer can tell you.

Jun 10, 2009 | 1989 Subaru Gl Wagon

1 Answer

1989 mustang ignition problems


check the fusible links on the starter solenoid

Jul 25, 2008 | 1989 Ford Escort

Not finding what you are looking for?
1995 Toyota Camry Logo

Related Topics:

134 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...