Question about Mitsubishi Colt

Open Question

When replacing centre bearing must i balance it thereafter

I have a mitsubishi colt d/c, 1996 model , i want to replace the center bearing, i want to know must i rebalance the whole propshat after i have fitted the new centerbearing

Posted by on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Mitsubishi Colt Cz3 1.3 2008 start problem in a cold seasons

This dosen't help but.........
I have a similar problem. Every 4 weeks or so the car refuses to start. Again battery is not a problem but if we use cables to jump start from another car it starts fine.
Mitubishi cannot find the answer, only suggestion was to spend £150 on a new key , however the problem has now occured with both of the keys !

Posted on Mar 04, 2010

Ad
mcdevito75
  • 1970 Answers

SOURCE: replace harmonic balancer 1996 mitsubishi 3000gt

mcdevito75 here, You"ll need speciall tools for this job, let your local shop do the job.

Posted on Jun 17, 2010

  • 1 Answer

SOURCE: Gear lever stiff and does not return to the centre

Hi, Permanant fix, take to garage and get them to replace link shaft on gear change mechanism. Or temp fix, get a tin of WD 40 with the plastic pipe that can be pushed onto the spray nozzle. Get a chopstick or simillar. Put chopstick down side of gear rubber gater. Do this by pulling blue rubber gater away from gear knob and gently inserting chopstick down into gater. Put the WD 40 plastic pipe down gater alongside the chopstick and spray a good amount. then roll the chopstick around to another possition and spray more WD 40. repeat until you have done it four or five possitions covering all round. Job done.

Posted on Aug 06, 2010

  • 5 Answers

SOURCE: mitsubihi colt 4x4 3000i d/cab model 2000

maybe its an axle the axle will make it shake

Posted on Sep 29, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the torque settings when replacing a Mitsubishi 2006, 2.8 tdi colt rodeo 2x4 wheel bearings


they need to be carefully lightly preloaded or 1 0r 2 thou clearance,best set by feel,not tight to spin wheel,no loose movement of wheel,you can feel it when you tighten nut where it suddenly stops

Feb 12, 2015 | Mitsubishi Cars & Trucks

1 Answer

Does 2006 1100cc colt have timing belt or chain and when should it be rereplaced


Pretty sure it has a timing belt and you should replace it at around 60,000 miles they are designed to last a lot longer but to be safe replace every 60,000 as well as the water pump and idler bearings

Jul 26, 2014 | 2006 Mitsubishi Colt

1 Answer

Autodata manuals


Timing mark/knotch is on the harmonic balancer that the pully bolts to on crankshaft.Mark said notch with a white paint pen and line it up with proper mark on tab bolted to block at the harmonic balancer.

May 09, 2014 | 2002 Mitsubishi Colt

1 Answer

How do i change front drivers wheel bearing/hub set on mitsubishi colt equippe 2005 model


Take wheel off, take off axle nut and split ring, take off calliper, remove rotor, look behind hub assembly should be 2 or more bolts holding it in place, remove them and pull off hub (sometimes needs to be hit with a hammer from behind to loosen... Picture is for a link of a different vehicle but same concept 4_17_2014_3_08_27_am.png

Mar 27, 2014 | Cars & Trucks

1 Answer

I need to know how to replace the clutch in a 1993 colt vista


0900c1528004723e.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 1: Clutch release bearing - 1990 Colt hatchback and sedan w/ 1.6L engine, 1990 Colt Wagon w/1.8L engine, and 1990-93 Vista


0900c1528004723f.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 2: Clutch driven and drive discs - 1990-93 all models


0900c15280047240.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 3: Clutch release bearing - 1990 Colt Wagon w/1.5L engine, 1991-92 Colt hatchback and sedan w/4-speed and 1993 Colt hatchback and sedan w/1.8L engine

  1. Remove the transmission or transaxle as outlined.
  2. Insert a pilot shaft or an old input shaft into the center of the clutch disc, pressure plate, and the pilot bearing in the crankshaft.
  3. With the pilot tool supporting the clutch disc, loosen the pressure plate bolts gradually and in a crisscross pattern.
  4. Remove the pressure plate and clutch disc.
  5. Clean the transmission and clutch housing. Clean the flywheel surface with a non-oil based solvent. Wash your hands before installing or handling the clutch assembly parts. Hold the clutch disc by the center hub only.

Before assembly, slide the clutch disc up and down on the transmission input shaft to check for any binding. Remove any rough spots with crocus cloth and then lightly coat the shaft with Lubriplate.
  1. To remove the throwout bearing assembly: Remove the return clip and take out the throwout bearing carrier and the bearing.
  2. To replace the throwout arm use a / 16 in. punch, knock out the throwout shaft spring pin and remove the shaft, springs, and the center lever.
  3. Do not immerse the throwout bearing in solvent; it is permanently lubricated. Blow and wipe it clean. Check the bearing for wear, deterioration, or burning. Replace the bearing if there is any question about its condition.
  4. Check the shafts, lever, and springs for wear and defects. Replace them if necessary.
  5. If you hadn't planned on replacing the clutch disc, examine it for the following before reusing it. Loose rivets. Burned facing. Oil or grease on the facing. Less than 0.3mm left between the rivet head and the top of the facing.
  6. Check the pressure plate and replace it if any of the following conditions exist: Scored or excessively worn. Bent or distorted diaphragm spring. Loose rivets.
  7. Insert the control lever into the clutch housing. Install the two return springs and the throwout shaft.
  8. Lock the shift lever to the shaft with the spring pin.
  9. Fill the shaft oil seal with multipurpose grease.
  10. Install the throwout bearing carrier and the bearing. Install the return clip.
  11. Grease the carrier groove and inner surface.
  12. Lightly grease the clutch disc splines.

The clutch is installed with the larger boss facing the transmission.
  1. Support the clutch disc and pressure plate with the pilot tool.
  2. Turn the pressure plate so that its balance mark aligns with the notch in the flywheel.
  3. Install the pressure plate-to-flywheel bolts head-tight. Using a torque wrench and, working in a crisscross pattern, tighten the bolts to 11-15 ft. lbs.
  4. Install the transmission or transaxle as outlined.
  5. Adjust the clutch as described in the following information.

Jan 07, 2013 | Cars & Trucks

2 Answers

I am trying to reset the srs light on my 1996 Mitsubishi colt. I have replaced the airbag and rotary switch(springs behind wheel) but cannot seem to locatate my airbag ecu. Where is the location of my...


If the airbag has been deployed, is is necessary to REPLACE the airbag (SRS) ECU. It is located below the center console. (See picture) It must be replaced because on your vehicle, it contains the crash sensors. If you do not replace it and hook-up new airbags and turn the key on, the new airbags will immediately deploy. There is no way to "reset" it.


dttech_92.gif

May 24, 2011 | 1996 Mitsubishi Mirage

1 Answer

Replace harmonic balancer 1996 mitsubishi 3000gt


mcdevito75 here, You"ll need speciall tools for this job, let your local shop do the job.

Jun 16, 2010 | 1996 Mitsubishi 3000GT

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

80 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...