Question about 1989 Jeep Cherokee

1 Answer

89 jeep cherokee 4.0 cranks and gets fuel but no spark... CHANGED THE IGNITION MODULE AND THE COIL.... still no spark. I just replaced my crank sensor and still no spark and wont fire up? wtf?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 293 Answers

If you can access a good engine control module (computer) replace it to your unit and try starting the engine again.

Posted on Jun 01, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1990 jeep Cherokee won't run but will crank. I hooked my battery up backwards? Everything else in and on my jeep works replaced ignition coil , distributor cap and rotor Any suggestions?


Ign module could be the problem do you have spark when cranking. If you have spark can you hear the fuel pump running while cranking. Let me know

Oct 03, 2015 | Jeep Cars & Trucks

1 Answer

My 89 jeep cherokee won't. Start it will turn over


what motor? is the coil producing spark?? If so, check the fuel pressure, if the fuel pressure is low drop the tank, repace the pump and also replace the filter (located on the frame forward of the tank). If the coil is not producing spark, check for shorts or opens in the circuits as well as the IGN fuses. If there is NO fuel pressure at all check the fuel pump fuses and make sure the fuel pump is plugged in and there are no opens in the circuit

Apr 07, 2012 | 1989 Jeep Cherokee

1 Answer

1995 jeep cherokee limited, motor cranks but will not start, smells like getting too much fuel


Then its probably not getting spark. You should test for spark. Probably a bad ignition coil. If you get a code reader hooked up to it and it says P.I.P. circuit failure than it is the pickup sensor in the bottom of the distributor. Could also have the Ignition control module tested. But probably just the ignition coil.

Sep 12, 2009 | 1995 Jeep Cherokee

1 Answer

I have an 89 Jeep Cherokee and it will crank over but not start


O2 sensor will not do that. Check the basics...do you have fuel...Do you have spark? I would make a bet on it either being a crank position sensor or fuel filter. Next good guess is the ignition coil. Check these items (in order) and see what you find. Test specs are found in any manual. (if you need specifics I can give them to you. You will need a decent volt/ohm meter to test.

Apr 04, 2009 | 1989 Jeep Cherokee

1 Answer

89 jeep cherokee 4.0 cranks and gets fuel but no spark... CHANGED THE IGNITION MODULE AND THE COIL.... still no spark.


the part that is known to fail in these engines that causes no spark is the Crankshaft position sensor, it is located on th right side of the bell housing as u stand in front of truck, it must be changed from below the truck and is very difficult to get at, here is a photo of the sensor and a brief description of the repair

Apr 03, 2009 | 1989 Jeep Cherokee

1 Answer

No spark at coil


check ignition pick-up coil and ignition module

Mar 31, 2009 | 1996 Jeep Grand Cherokee

1 Answer

Jeep won't start


Check voltage at coil. Check coil output (spark should be healthy even at 1/4" away from ground). If OK, then change module The only testing on module is with a special tool. Therefore if contacts are clean, that's all you can do with it!

Jan 27, 2009 | 1993 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

382 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...