Question about 1992 Audi 100

1 Answer

Will not shift properly

All shift indicator lights are on. (PRND123) Trans bangs when put into Reverse or Drive. Trans does not shift up or down. I would guess it is stuck in 3rd gear. Even when I shift manually, no change in gear.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,509 Answers

Tranny could be bad or the switch that indicates position not only to the start circuit and the backup lights. and allows the car to be started in neutral. whis swich can bind and may need replaced as it when removed should turn with little or no resistance

Posted on Aug 16, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Transmission does not go into gear.


Hi, check that the cable is attached to the gear selector on the trans and does the shift quadrant move as it usually did.... not sticking or stiff in it's movement. Auto's are basically a hydraulic pump forcing oil in through valves and galleries in the valve body,,,, it could be that a gallery is blocked or that a valve has jammed shut..... check all electrical connectors for a proper fit..... do all the lights on the shift indicator light up as normal, no engine check light coming on ?

Dec 20, 2012 | 2000 Ford Taurus

1 Answer

My 93 GTP,3.4 When put in reverse to leave my yard has a sum what of a hard bang and shifts hard.I replaced the dog bone bone but thats not the problem. Would a worn CVC jiont do this? What could it


Cv joints usually knock or click, especially when turning. Open the hood, start the engine and while looking at the engine from the drivers seat put foot on brake and shift to reverse. if the engine jumps, must have a bad mount. also may try giving it a little gas while holding brake to make sure. also try it it drive as well. chances are its the trans mount going bad.


note: if there are any oil leaks that are getting the mount wet it will continue to fail.

Aug 14, 2012 | 1993 Pontiac Grand Prix

2 Answers

How do you adjust the shift cable on a 1995 gmc jimmy, wont go into reverse or park.


On the 1995 Jimmy, the shift cable can come loose on the mount on the side of the transmission where the cable meets the trans. When it slips, the alignment goes off and causes the driver to not be able to put the trans into park. If you take a long stick you can push the shift arm on the trans to the park position and your trans will go into park.....what you (and I) really need to know is how to take the shift cable mount apart and reset it.

Aug 05, 2012 | GMC Jimmy Cars & Trucks

1 Answer

Put my 2004 tahoe in reverse heard a loud bang,now no reverse.Put in drive it runs but seems to rpm high before shifting,what might problem be ?


Pull the Trans out & have it rebuilt

No other solution,your done,finished

Don't even question my answer,it slips,
your done

Jun 11, 2012 | Chevrolet Tahoe Cars & Trucks

1 Answer

Shift Indicator Module PRND123 illuminate, but LED for each position do not light up


This is a common problem and the issue is with the display of the gear selector, it must be replaced. You will need to remove the cluster form the car and send it into a GM approved repair center for replacement of the display.

Feb 21, 2012 | 1997 Pontiac Grand Am

1 Answer

Transmission multiple shifting/banging under load


start engine chock back of drive wheels ,put in reverse and then check oil level

Jul 02, 2010 | Lincoln Continental Cars & Trucks

2 Answers

2000 chevrolet tahoe - can't put the gear stick in park. Can put gear stick in reverse and drive. Can drive and drive in reverse. But cant put gear stick in park.


The Shift Interlock Is Not Working Check If Brake Lights Work If Not May Be A Fuse Prob Or Brake Light Switch The Switch actuates The Lock

Mar 04, 2009 | 1995 Chevrolet Tahoe

1 Answer

How do you know if your torque converter is bad on Jeep wrangler


First check fluid. Make sure it's full and clean and does not smell burned (compare to another good car)
Converter failure is usually most obvious when trans shifts to OD. if shift is late or makes bang noise going in, you likely have a problem. to check lockup, after od engages, lightly touch brake, trans should momentarily shift out of od. Whining is usually due to low fluid. Also check transfer case and both differentials for proper level and leaks.

Jan 24, 2009 | 1998 Jeep Wrangler

1 Answer

No reverse


U are going to have to have the trans torn down and replace the reverse clutch drum.

Nov 22, 2008 | 1999 Chevrolet Silverado 1500

Not finding what you are looking for?
1992 Audi 100 Logo

425 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

yadayada
yadayada

Level 3 Expert

75807 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14333 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...