Question about 1995 Buick Skylark

1 Answer

How to install intake manifold gaskets and their location.

Im installing a intake manifold and need to know which way the gasket block plates face. Do the gasket block off plates go front or back How do I get to the intake manifold on a 1995 Buick Skylark?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 35 Answers

Go to autozone.com and register free then select make year ect.
select repair info (you have to register 4 this)
step by step and photos!!!!

Posted on May 31, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1982 280zx i replaced my manifold gasket and all of a sudden im having over heating problems


You're obviously referring to the intake manifold gasket, right? When you removed the manifold, did you old gasket to the replacement for size and mounting match-up? Did you have to scrape off the old gasket, and were you careful to not let any pieces of it fall into either the manifold or the head? Chances are, either the replacement gasket (OEM gasket or aftermarket?) did not match up correctly with the manifold or the head and is blocking a coolant channel, or a piece of the old gasket has lodged in the water jacket or has found its wa to the water pump and is blocking the coolant circulation. Bad result would be damage to the water pump requiring its replacement; worse result would be overheating of the engine causing failure of the head gasket and/or possible warpage of the head. If you're certain that the replacement manifold gasket was a perfect match and was placed properly during installation, you may want to drain and power-flush the cooling system, refill with water and recheck the temp. If it's OK, drain the system again and refill with prescribed mix of antifreeze and water. If you're not certain, you'll probably need to pull off the intake again and use another new gasket that exactly matches up with the water jacket ports on both the manifold and the head. Good luck.

Oct 03, 2013 | Datsun Cars & Trucks

1 Answer

How to fix oil leaks in chevy ss impala 1996



Instructions

1. Removal

Unscrew the bolt that holds the negative connection to the Impala's battery. Set this bolt aside for later use.

Remove the engine cover to access the intake manifold and manifold gasket. Disconnect the throttle body inlet duct from the engine.

Twist off the radiator cap to allow draining of the coolant to flow more smoothly. Place an empty container beneath the radiator's drain plug, and remove this plug. Allow all of the engine coolant to drain into the empty container. Replace the drain plug once you are finished.

Tag all of the electrical wiring and hoses before removing so that reconnection is precise to factory settings. Remove these parts, individually, from the intake manifold.

Loosen the bolts that hold the intake manifold to the Impala's engine block. Lift the intake manifold from the block once all bolts have been completely removed.

Use the flat-head screwdriver to pry the old intake manifold gasket from the engine block. Discard this part once you have removed it.

Clean the engine block thoroughly with the engine degreaser and linen cloth. If necessary, use a gasket scraper to remove excess buildup and grime.

2. Installation

  • Coat the top and bottom of the new intake manifold gasket with a chemical sealer so that it bonds to the engine block securely. Position this new manifold gasket so that it lines up perfectly with the cylinder ports of the Impala's engine block.

Place the old intake manifold on top of the newly-installed manifold gasket until it aligns with all of the holes of the cylinder flanges and manifold gasket.

Attach all of the bolts with your hand to the manifold. Once all bolts have been positioned, use a torque wrench and apply 15 foot-pounds of pressure to the bolts to secure the manifold into place.

Reconnect all of the necessary hoses and electrical wiring to the intake. Pour the engine coolant back into the radiator.

Reattach the engine cover on top of the intake manifold and engine block. Start the Impala's engine and check for any leaks around the new intake manifold gasket.

Jul 08, 2012 | 1996 Chevrolet Impala SS

1 Answer

Change head gasket on 65 mustang 200


Drain antifreeze -DON"T POUR IT DOWN A STORM DRAIN - then remove valve cover, Remove exhaust from head assembly. On this engine the head is also the intake manifold - it's cast as a unit. Remove carb and remove heater hoses from carb base plate. Remove head bolts and discard. Break head loose from block - may have to smack it a time or two to break gasket loose. Get a buddy to help lift the head off the block - it's fairly heavy. Clean gasket surfaces on both head and block. Install new gasket onto block - pay attention to gasket orientation - it goes on only one way correctly. Reverse procedure to re-install - USE NEW HEAD BOLTS! Silly to try to save $20 bucks on bolts and ruin an engine.

May 05, 2012 | 1966 Ford Mustang

1 Answer

What is the torque specs on intake 4.3 l v6 vortec


0900c1528008ee89.gif

To install:

  1. Clean all gasket surfaces completely.
  2. Install the intake manifold gaskets with the port blocking plates facing the rear of the engine. Factory gaskets should have the words "This Side Up" visible.
  3. Apply gasket sealer to the front and rear sealing surfaces of the engine block.
  4. Apply a 0.197 inch (5mm) bead of RTV sealer to the front and rear of the block. Extend the sealer approximately 1 / 2 -inch (13mm) onto the heads.
  5. Install the lower intake manifold.
  6. Apply sealer to the lower intake manifold bolts prior to installation.
  7. Install the bolts and tighten in sequence and in 3 steps as follows:
    1. First step to 26 inch lbs. (3 Nm).
    2. Second step to 106 inch lbs. (12 Nm).
    3. Final step to 11 ft. lbs. (15 Nm).

  8. If removed, install the alternator bracket bolt.
  9. Install the coolant by-pass hose.
  10. Install the EGR valve.
  11. Connect the upper radiator hose to the thermostat housing.
  12. Connect the heater hose to the lower intake manifold.
  13. Connect the fuel pressure and return lines to the lower intake manifold.
  14. Connect the wiring harnesses and brackets to the lower manifold.
  15. Install the throttle cable bracket, then attach the throttle cable and the cruise control cable (if equipped).
  16. Install the transmission oil level indicator and tube, if equipped.
  17. Install the EGR tube, clamp and bolt.
  18. Install the PCV valve and hose.
  19. Install the A/C compressor and bracket.
  20. Install the distributor.
  21. Install the upper intake manifold.
  22. Fill the cooling system.
  23. Connect the negative battery cable.
  24. Start the vehicle and check the ignition timing (not adjustable).
  25. Verify no oil, coolant, vacuum or fuel leaks.

    0900c1528008ee88.gif

  26. Install the intake manifold bolts and tighten them to 35 ft. lbs. (48 Nm) in the sequence shown.

May 09, 2011 | Chevrolet TrailBlazer Cars & Trucks

1 Answer

Torque sequence for 1996 chevrolet van intake manifold with a 4.3 litre moter


Ha, you tried to fool me with the bit about a 3.5 L motor--I could find that one...here is the complete procedure from AutoZone.com:




Installation To install:
  1. Clean the gasket mounting surfaces. Be sure to inspect the manifold for warpage and/or cracks. If necessary, replace it.
  2. Position the gaskets on the cylinder head with the port blocking plates to the rear and the This Side Up stamps facing upward. Then apply a 3 / 16 in. (5mm) bead of RTV sealant on the front and rear of the engine block at the block-to-manifold mating surface. Extend the bead 1 / 2 in. (13mm) up each cylinder head to seal and retain the gaskets.

    0996b43f80208c7b.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Lower intake manifold tightening sequence-4.3L engines
  3. Install the lower intake manifold. Tighten the bolts in sequence and in 3 steps, as follows:


    1. Step 1: 26 inch lbs. (3 Nm).
    2. Step 2: 106 inch lbs. (12 Nm).
    3. Step 3: 133 inch. lbs. (15 Nm).

  4. Install or connect the following:

    Power steering pump Alternator bracket bolt near the thermostat housing Wiring harness to the lower manifold components, including the injector, EGR valve and ECT sensor Air conditioning compressor bracket-to-the lower intake manifold pencil braces
  5. Install transmission oil dipstick tube, if necessary.

    Fuel supply and return lines to the rear of the lower intake
  6. Temporarily reattach the negative battery cable, then pressurize the fuel system (by cycling the ignition without starting the engine) and check for leaks.
  7. Disconnect the negative battery cable.
  8. Install or connect the following:

    Heater hose to the lower intake Upper radiator hose to the thermostat housing Distributor assembly and engage the wiring Ignition coil Connect vacuum hoses to the upper and lower intake manifold. New upper intake manifold gasket, making sure the green sealing lines are facing upward Upper intake manifold Manifold retainers. Tighten them to 88 inch lbs. (10 Nm) using two passes. Purge solenoid and bracket Brake booster vacuum hose at the upper intake manifold PCV hose to the rear of the upper intake manifold Vacuum hoses to both the front and rear of the manifold assembly Throttle body Throttle linkage to the upper intake Wiring to the upper intake components including the TP sensor, IAC motor, MAP sensor and the fuel meter Engine cover Air intake assembly
  9. Connect negative battery cable.
  10. Refill the engine cooling system.
  11. Start the engine and check for leaks.

Aug 26, 2010 | 1996 Chevrolet Astro

2 Answers

Torque specification on a 2003 alero cylinder heads 3.4 liter


3.4L Engine To Remove:
  1. Remove the lower intake manifold.
  2. Remove the exhaust crossover pipe.
  3. If removing the right cylinder head, remove the catalytic converter from exhaust manifold.
  4. If removing the left cylinder head, remove the engine oil dipstick and tube.
  5. Remove the rocker arms and pushrods.
  6. Remove and discard the cylinder head bolts.
  7. Remove the cylinder head.
  8. Clean the mating surfaces on the following items:
    • Cylinder head
    • Cylinder block
    • Intake manifold
  9. Clean the cylinder block bolt threads.
NOTE: During disassembly, keep the valve train components together for proper location during assembly.
To Install:
NOTE: Coat the cylinder head bolt threads using thread sealer.
  1. If removed, install the following components:
    • Exhaust manifold
    • Accessory studs
    • Spark plugs
  2. Place the cylinder head gasket in position over the dowel pins. Ensure that the THIS SIDE UP note is showing.
  3. Install the cylinder head. Cylinder head torque sequence ’99-‘00 gmpc_v6_14.gif

    Cylinder head torque sequence ’01-05 gm-03-34-682.gif

  4. Install the new cylinder head bolts.
    • Tighten the cylinder head bolts a first pass to 44 ft lb (60 Nm).
  5. Tighten the cylinder head bolts in sequence an additional 95 degrees.
  6. Install the intake gasket.
  7. Install the pushrods and rocker arms.
  8. Raise and support the vehicle.
  9. Install the catalytic converter and dipstick tube and indicator if removed.
  10. Lower the vehicle.
  11. Install the exhaust crossover pipe.
  12. Install the intake manifolds.
  13. Connect negative battery cable.
  14. Fill the cooling system.

Jul 03, 2010 | 2003 Oldsmobile Alero

2 Answers

HOW TO REPLACE INTAKE MANIFOLD ON A LINCOLN


answer , very carefully ...

drain coolant , remove and mark all vacuum lines , make a schematic to diagram your hose routing, disconnect and plug all fuel lines, remove distributor and mark location of rotor, disconnect battery, remove any necessary cables, brackets and or accesseries, remove intake mounting bolts, note length of bolts and reference location, pry up on intake , remove intake, scrape old gasket off , must be very clean to reinstall new gasket or you will cause a leak..

Nov 02, 2009 | 1999 Lincoln Town Car

1 Answer

EGR VALVE 1999 MERCURY COUGER


SECTION 303-08: Engine Emission Control 1999 Cougar Workshop Manual REMOVAL AND INSTALLATION Exhaust Gas Recirculation (EGR) Valve Removal
  1. Remove the air cleaner outlet tube.
    1. Disconnect the intake air bypass hose.
    1. Disconnect the positive crankcase ventilation hoses.
    1. Remove the air cleaner outlet tube.
  1. Disconnect the tube from the exhaust gas recirculation valve.
  1. Remove the exhaust gas recirculation valve.
    • Disconnect the vacuum hose.
Installation
  1. sxu~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: When cleaning the gasket faces, do not allow debris to enter the intake manifold or exhaust gas recirculation valve.
    Clean the gasket faces of the intake manifold and exhaust gas recirculation valve.
  1. Install a new exhaust gas recirculation valve gasket.
  1. Position the EGR valve and install the bolts.
    • Install the vacuum hose.
  1. Connect the EGR tube.
  1. Install the idle air control valve. For additional information, refer to Section 303-14A . For additional information, refer to Section 303-14B .

Sep 15, 2009 | 1999 Mercury Cougar

1 Answer

Intake manifold gasket / replace


3.8L Engine

NOTE The 3.8L (VIN K) non-supercharged engine uses a two-piece intake manifold consisting of an upper air plenum which mounts the throttle body and a lower intake manifold assembly which houses the fuel injectors. The 3.8L (VIN 1) supercharged engine uses a similar lower intake manifold. The supercharger serves as the upper manifold.
Lower Manifold

NOTE Two bolts which fasten the lower intake manifold to the cylinder head are accessible only after the upper intake manifold is removed. These bolts are located in the right front and left rear corners of the lower intake manifold. Remove the upper intake manifold to service the lower intake.
The 3.8L (VIN 1) supercharged engine uses a manifold similar to the 3.8L (VIN K), but the supercharger serves as the upper manifold.
  1. Disconnect the negative battery cable.
  2. On 3.8L (VIN 1) engines, remove the supercharger assembly. Please see the procedure in this section.
  3. Remove the upper intake manifold using the procedure above.
  4. Remove the EGR outlet pipe from the intake manifold.
  5. Detach the engine coolant temperature sensor wiring harness from the sensor.
  6. Remove the lower intake manifold bolts and carefully lift off the manifold.

To install:


0900c15280269f1b.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Lower intake manifold bolt torque sequence-3.8L (VIN K) engine
  1. Clean all parts well with degreaser, especially the gasket seal surfaces on the upper and lower manifold pieces and between the lower manifold and the cylinder heads..
  2. Install new gaskets to the cylinder heads and new seals to the engine block. Carefully lower the manifold into place. Apply thread-locking compound to the bolt threads. Make sure to install the two hidden bolts in the lower intake manifold. Hand start all bolts, then torque evenly to 11 ft. lbs. (15 Nm). Follow the toque sequence, starting in the center, then working outwards in a circle.
  3. Install the remaining components in the reverse order of the removal process.

Upper Intake Manifold (Plenum)
  1. Disconnect the negative battery cable.
  2. On 3.8L (VIN 1) engines, remove the supercharger assembly. Please see the procedure in this section.
  3. Tag for identification, then remove the right side spark plug wires.
  4. Disconnect the ignition wires from the fuel rail.
  5. Remove the fuel rail. Please see Section 5.
  6. Remove the cable bracket from the intake manifold.
  7. Remove the throttle body.


NOTE Two bolts which fasten the lower intake manifold to the cylinder head are accessible are accessible only after the upper intake manifold is removed. These bolts are located in the right front and left rear corners of the lower intake manifold.
  1. Remove the upper intake manifold bolts and carefully lift the upper intake manifold from the engine.



0900c15280269f1c.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Upper intake manifold and bolt torque sequence-3.8L (VIN K) engine
To install:
  1. Clean all parts well with degreaser, especially the gasket seal surfaces on the upper and lower manifold pieces.
  2. Install new gaskets to the cylinder heads and new seals to the engine block. Carefully lower the manifold into place. Make sure to install the two hidden bolts in the lower intake manifold. Hand start all bolts, then torque evenly to 89 inch lbs. (10 Nm). Follow the torque sequence, starting in the center, then working outwards in a circle.
  3. Install the remaining components in the reverse order of the removal process.

Sep 11, 2009 | 1999 Buick Regal

1 Answer

How to install intake manifold gaskets


The plates go to the rear. On most gaskets it will say up so place the plates to the rear and up per the markings. Good Luck

May 29, 2009 | 1992 GMC Sierra K1500

Not finding what you are looking for?
1995 Buick Skylark Logo

Related Topics:

811 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...