Question about 2000 Ford Expedition

1 Answer

Where can the keyless code entry be found???

Where on my vehicle can i find this code????

Posted by on

  • KEN LaPOINT
    KEN LaPOINT May 11, 2010

    There should be a credit card sized card in with the owner's manual in the zipper binder.. with a 6 digit number on it...

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 318 Answers

The keyless entry code is on the out side of the anti theft control module . The module is locate under the dash on the drivers side there will be a sticker on the out side of the module with the code on it

Posted on May 31, 2009

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: I PURCHASED THIS 2004 AVIATOR USED WITH NO KEYLESS ENTRY CODE.

the keyless code is by the right rear door panel. open the door, remove the panel that's over the the seatbelt. after doing that open but you don't have just kind of stretch out and their you will find a black box or reciever with a sticker and a 5 digit code stamped on it. if you want to change the passcode refer to your manual, but you'll need the original code to be able to change it.

Posted on Nov 13, 2008

zappanut
  • 959 Answers

SOURCE: reprogram keyless entry system

1991-94 Nissan Maxima key less entry reprogramming procedure:

1. Enter the *original code found under the dashboard.
(*the code begins with the letter F and has 7 digits)

2. Close the doors and lock all of the doors,
enter the 7 digit code ( make sure you have your key in hand).

3. Once the code is entered correctly you will hear a long beep ♪ ♫.
While the beep ♪ ♫ is sounding ... ENTER your NEW 4 digit code, (you will then hear random beeps ♪ ♫)
Do not touch anything until the beeping ♪ ♫ stops.

4. To open the doors, the front windows and the trunk,
type: S(Clear) and the New 4 digit code and the door will open automatically.

5. IF by any chance you forget your new code. Just enter the original one and start all over.

Posted on Dec 15, 2008

chuck943
  • 783 Answers

SOURCE: CHANGE CODE ON KEYLESS ENTRY SYSTEM FORD EDGE

Yes you can program your own code by inputting the original code then hit the no. 2 button then input your own 5 digit code.

Posted on Mar 16, 2009

  • 1986 Answers

SOURCE: how to change keyless entry code when I don't know the current

Open the right/rear door. Pull the rubber weatherstrip back from the door opening. Fold the right/rear seat back down into a locked position, in order to access to the right/rear trim panel. Carefully, pry the right/rear upper trim panel housing the right/rear seat belt height adjuster. Now carefully pry back the lower trim panel taking care now to break it, exposing the vehicle security module with three connectors plugged into it, coloured green, blue, and grey. Look on the label that has the part number which should end in EB. There are FIVE numbers to the right of that number. Those five numbers are your keyless entry keypad code.

Posted on Sep 15, 2009

greg_margo
  • 1959 Answers

SOURCE: need to change the factory keyless entry code OR the module

Programming your own personal entry code
To program your own code:
5. Enter factory set code (keypad will illuminate when pressed).
6. Press 1/2 control within five seconds of step 1.
7. Enter your personal 5 digit code.
Enter each digit within five seconds
of previous one.
8. After the code is entered, the
locks will cycle, confirming that the
new code has been set.
Do not set a code that includes five of the same number or presents
them in sequential order. Thieves can easily figure out these types of
codes.

Keep in mind, if the battery is ever replaced or goes dead, the keycode will revert back to the factory setting.

Posted on Sep 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I reset keyless door entry that is in lock out mode


Viper Keyless Entry Systems

https://www.viper.com/car/keylessentry/
Viper is the industry leader in keyless entry systems. Add the convenience of keylessentry to virtually any vehicle - even vehicles without power door locks!

Alarms, Remote Car Starters, Keyless Entry & Locks - JC ...

www.jcwhitney.com > Audio, Video & Electronics
20 out of 32 products in Alarms, Remote Car Starters, Keyless Entry & Locks ..... ofKeyless Entry & Car Alarms allow you to lock and unlock power door locks.
How to program your keyless entry keypad - Ford Ownerhttps://owner.ford.com/.../locks.../how-to-program...Ford Motor CompanyDiscover how to lock and unlock your doors and how to program memory settings that will adjust seats & mirrors for each driver.SecuriCode™ Keyless Entry Keypad - Ford Ownerowner.ford.com/.../locks.../securicode-keyless-entr...Ford Motor CompanyLearn how to set a 5 digit SecuriCode on the Ford keyless entry keypad. ... Sign out. Register/Sign In · Your Vehicle. Service & Maintenance. Service & .... vehicle's SecuriCode keypad to lock and unlock your doors without having to use a key. ... Thekeypad will go into an anti-scan mode if you enter the wrong code seven ...How Programming Your Keyless Entry Can Make ... - Ford Life

Jan 08, 2016 | Cars & Trucks

1 Answer

Is the igntion key code and the keyless remote code the same if so where can i find it looked under trunk


You do not say what kind of vehicle and why the dealer could not issue a new key using the VIN. I know of no manufacturer that writes down the codes anywhere in the vehicle. The keyless entry is controlled by it's own module and is verified by the main computer. The ignition key carries the code on it, and is verified by the ignition module. A good locksmith shop should be able to make keys for you.

Feb 05, 2012 | 1998 Lincoln Continental

2 Answers

I just bought a used MercuryMountaineer 2004. I do not know the code to the side for numeric keyless entry. How would I reset it to my own code?


You need to go to the dealer, to get the
MFG Code and instructions for the
Keyless Entry System,then you can
put in your own code

Mar 11, 2011 | Mercury Mountaineer Cars & Trucks

1 Answer

I don't have a manual for my 2004 lincoln Avaitor but would like to know how I can change the code on the drives door key pad


KEYLESS ENTRY SYSTEM With the keyless entry keypad, you can: • lock or unlock the vehicle doors without using the key. Your vehicle has a factory set 5 digit code that operates the keyless entry system. You can also program your own 5 digit personal entry code. The factory-set code is located: • on the owner's wallet card in the glove compartment • or at your dealer. When pressing the controls on the keyless entry keypad, press the middle of the controls to ensure a good activation. This system will disable the power door lock controls. These will not work until the vehicle is disarmed. Programming your own personal entry code To program your own code: 5. Enter factory set code (keypad will illuminate when pressed). 6. Press 1/2 control within five seconds of step 1. 7. Enter your personal 5 digit code. Enter each digit within five seconds of previous one. 8. After the code is entered, the locks will cycle, confirming that the new code has been set. Do not set a code that includes five of the same number or presents them in sequential order. Thieves can easily figure out these types of codes. Your personal code does not replace the permanent code that the dealership gave you. You can use either code to unlock your vehicle. If a second personal code is entered, the module will erase the first personal code in favor of the new code. Locks and Security 149 Locks and Security If you wish to erase your personal code, use the following instructions: 1. Enter factory set code. 2. Press 1/2 control and release. The system will now only respond to the factory set code. Anti-scan feature The anti-scan feature prevents repeated attempts at arriving at a valid key code. The keyless entry pad is disabled for 1 minute after 7 unsuccessful attempts (35 consecutive button presses) at entering a valid key code. The keypad will flash during this 1 minute mode. However, the 7/8 and 9/0 controls will still lock the vehicle. Anti-scan will be turned off after: • one minute of keypad inactivity. • the remote entry transmitter UNLOCK button is pressed. • the ignition is turned to the ON position. Unlocking the doors with the keyless entry system To unlock the driver door, enter either the factory set code or the personal code (each digit must be pressed within five seconds of the prior digit). The interior lamps will also illuminate. To unlock all doors, enter the factory set code or personal code (driver door unlocks) and press the 3/4 control within five seconds. Locking the doors with the keyless entry system It is not necessary to enter the factory or personal code prior to locking all doors. To lock the doors: • with the driver's door closed, press the 7/8 control and the 9/0 control at the same time.

Dec 17, 2009 | 2004 Lincoln Aviator

2 Answers

How do i reprogram keyless entry codes


door pad keyless codes?

in owner manual, enter permanent code and then press "1" and enter personal code, then press "1" again. Then both codes will work.

If you don't have manual, go to Motorcraft.com and click on technical resources and click on your year owner manual.

---------------------------------------------
Each vehicle equipped with a keyless entry keypad is programmed with a five-digit entry code. This code is provided to the customer through a wallet card in the Owner Literature package. In addition, this code is available through a diagnostic tool and is also printed on the vehicle security module label. When entering codes each digit must be entered within five seconds of the previous button press.
Programming/Erasing Personal Code
A unique personal five-digit code can be programmed by following these steps:
  1. Enter the factory set five-digit code (the keypad will illuminate when pressed).
  1. Press 1/2 within five seconds of Step 1.
  1. Enter the unique five-digit code.
The personal code does not substitute for the permanent factory set code. Either code can be used to access the vehicle. In addition, if a second personal code is programmed, it will simply overwrite the previous personal code. To erase a personal code, carry out the following procedure:
  1. Enter factory set five-digit code.
  1. Press 1/2 within five seconds of Step 1.
  1. Press 7/8 and 9/0 at the same time within five seconds of Step 2.
The system will now only respond to the factory set code.
Anti-Scan Feature
To provide added security, the keyless entry pad is disabled for one minute after 35 button presses without a valid entry code being entered. The keypad will flash during this one-minute mode with all functionality disabled except for 7/8 and 9/0 still being allowed to lock the vehicle.
Anti-Scan will be turned off after any of the following events:
  • one minute of keypad inactivity
  • the keyless entry remote transmitter UNLOCK button is pressed
  • the ignition is turned to the ON position.
Unlocking the Doors with the Keyless Entry Keypad System
To unlock the driver door, enter either the factory set code or the personal code (each digit must be pressed within five seconds of the prior digit). The interior lamps will illuminate.
To unlock all doors, enter either the factory set code or the personal code (driver door unlocks) and press the 3/4 control within five seconds.
Locking the Doors with the Keyless Entry Keypad System
It is not necessary to enter the factory set or personal code prior to locking all doors. To lock all doors, press the 7/8 and 9/0 controls at the same time.
Inspection and Verification
  1. Verify the customer concern by operating the system.
  1. Visually inspect for obvious signs of mechanical or electrical damage.

Dec 01, 2009 | 2004 Ford F350

2 Answers

I just purchased an expidition 2003, the car lot does not have the code for the keyless entry how can i locate this


In most cases the dealership where it came from placed stickers under the hood, in the door jam, and under the rear hatch. It will be a 5 digit number that can also be found in the vehicle manual if you have these. If none of these exist then the ford dealer will be able to find it for you for a small charge by hooking up to the vehicle computer.

Oct 27, 2009 | 2003 Ford Expedition

1 Answer

Would like to rekey my auto-keyless entry and cannot find the code near the instrument panel.


your factory code for keyless entry by number pad? this is found on the module for keyless entry located under dash left side, number on module in BOLD type is the original or factory code

May 18, 2009 | 2004 Ford Expedition

1 Answer

I bought a used car with a keyless entry and don't have the code.


keyless entry module is found in rear of vehicle either left or right side behind some trim panels, there will be the five digit code you are seeking.  If you are having difficulty, call the local dealer and ask where the vehicle had been purchased or had warranty service.  Call that dealer and ask for the code, it should be on file.  Keep me posted.

Jan 25, 2009 | 2007 Ford Expedition EL XLT

3 Answers

Keyless entry


I believe dealer has to re-program the new code.

Aug 29, 2008 | 2001 Ford Explorer Sport Trac

3 Answers

Entry code om drivers door


The keyless entry module is located in the rear of the vehicle on the driver's side. You will need to partially remove the left rear panel in the cargo area. You will then see the keyless entry module bolted behind a metal reinforcement bar. There is a sticker on the module that has the 5 digit entry code.

May 26, 2008 | 2001 Mercury Mountaineer

Not finding what you are looking for?
2000 Ford Expedition Logo

357 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...