Question about 1993 Ford F150 SuperCab

1 Answer

1996 Ford F-150 300 inline 6 timing gears/timing issue

I just finished changing the timing gear on my 1996 Ford F-150 300 inline 6. It will start and run but it runs rough and louder than before. (Like a diesel engine) I know that my gears are aligned with each other and I have not messed with the distributor. How do I adjust the timing? Do I have to bypass the computer? Any other suggestions? Thanks

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 74 Answers

U have to unplug the spout small gray plug on driver side in the eng comp . on the fender wall on plug that set timming thing it should b 10 deg b4 top dead center then plug spout back in comp will adv timming

Posted on May 31, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1990 Ford f 250 4.9 inline 6 misfires/skips at high rpm I've only noticed it in 2nd gear always does it at high rpm right before I change into 3rd


run the fault codes
as you can achieve naerly full rpms in 2nd gear it is possible that the misfire is from low fuel pressure in the fuel manifold
could be a venting problem in the EVAC system, filter fault, pump failure and pressure regulator problem
I doubt that it would be a ignition area problem as it would occur in 1st as well as other gears

Jul 11, 2015 | Ford Cars & Trucks

1 Answer

96 ford f150 300 inline 6 put timing gears on it now no reverse.


Timing gears has nothing to do with the transmission. Is it auto manual? Does it go into gear and just go in reverse or wont go into gear.. Check linkage for binding if it just wont go after putting in gear it is trans problem..good luck.

Dec 06, 2014 | Ford F-150 Cars & Trucks

1 Answer

My 1996 Ford F150 300 Inline 6 Cylinder just goes Click when i turn the Ingnition


if solenoid is clicking may mean its working and problem is dead spot in starter ---but test and check them with a meter

Jun 13, 2017 | 1996 Ford F150 Regular Cab

1 Answer

Will a transmission from a 1990 F150 289 motor work with a 1996 F150 inline 6 300 motor?


if its look the same then it will work ,dont worry about gear ratios and all the technical stuff so long as the electronic stuff lines up away you go and it dont fit then make it fit

Nov 29, 2013 | 1982 Ford F 150

2 Answers

What is the second drive gear for


The first one is over drive and the second is drive. It is best to just use overdrive when on the parkway and drive on slower back roads when there is hills and stop and go traffic. Overdrive is a higher gear.

Dec 09, 2011 | 1998 Ford Taurus

1 Answer

1989 Ford F-150 4.9L 300 inline 6 cylinder 5 speed stuck in 3rd Gear? any solutions


If your clutch master cylinder is good in all other gears: you can disengage and, shift the other gears with the engine not running and, you have the correct amount of clutch fluid
in your clutch master cylinder: to release the clutch:
you have a broken 5th gear syncro and, a bent fork
remove the transmission and, when you remove the shift cover you will
see the problem; you must drain the transmission case remove any metal debris; remove the gear set and, replace the syncro...the fork can probably be
re-straightened use clean, new case oil when you reassemble the transmission.

Aug 04, 2010 | 1989 Ford F 150

1 Answer

I have a 1996 Mercedes C250 Sport TD Auto with agearbox problems. Yesterday when i started the car up & tried to pull away it will only go in first gear It will not change gear even when trying to do...


Suggest changing fluid and filter as old fluid can cause issues. Also Pistons on the side of the transmission can be changed without removing them. When they break you can lose gears. If that doesnt work time for a rebuild.

Jun 16, 2010 | 1996 Mercedes-Benz C-Class

1 Answer

Slipping transmission.


The friction plates maybe well worn and need replaced. Torque converter may be failing. Automatic transmissions can and will wear out in time. 14 years is alot for any vehicle.

May 30, 2010 | 1996 Ford Explorer

1 Answer

1996 chevy z24 2.4 car has a hard time starting and staying runni


When is the last time you changed the plugs and or wires. Possibly a bad coil. You can also check the fuel injectors to see if they are spraying correctly. Also check the fuel filter. It should be inline under the car just look for the lines when you crawl underneath. If none of that is the issue let me know

Jan 06, 2009 | 1988 Chevrolet Cavalier Z24

Not finding what you are looking for?
1993 Ford F150 SuperCab Logo

981 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...