Question about 2008 Nissan Versa

1 Answer

Can't remove 2007 nissan versa tail light assembly

I've removed the 10mm bolts but the assembly won't budge, even after I put pressure on the interior bolts. I understand there may be a plastic clip holding it on and I'm afraid of breaking it if I use too much pressure. Any photos of this would be great! Thanks! we are trying to replace a burned out tail light and cannot remove the assembly. Any pictures would be great.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

You have to rip it out after removing the two 10 mm nuts, the catch at the front was not designed to let go until you bang it and cause the shade to break , stupidest thing I ever saw

Posted on Oct 23, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Removing tensioner assembly


images for 2008 Nissan Versa Removing tensioner

    how do you remove tension off surpentine belt tensioner - Nissan Forum

    www.nissanforums.com/.../151350-how-do-you-remove-tension-off.htm...

    Feb 20, 2009 - 4 posts - ‎2 authors
    2008+ Nissan Rogue ... QR25 2.5L Engine Engine Discussion: 2002+ Sentra SE-R and SpecV ... how do you remove tension off surpentine belt tensioner ... changed these before, but which way do you turn the tensioner, how ... Replacing the Water Pump on a '04-'08 Maxima *DIY*
    1 post
    Aug 31, 2011
    Belt noise: replace idler pulley? - GA16DE
    8 posts
    Sep 16, 2008
    Step by step instructions -Upper Timing Chain Tensioner
    15 posts
    Dec 8, 2007
    Idler Pulley Bearing Replacement Info
    5 posts
    May 16, 2003
    More results from www.nissanforums.com

    Nissan Versa Tensioner Pulley Issue (1/1) - EricTheCarGuy ...

    www.ericthecarguy.com/.../50669-nissan-versa-tensioner-pulley-issue
    Nissan Versa Tensioner Pulley Issue 1 year 7 months ago #94552 ... for a 50 Torx to be used to remove the entire tensioner pulley assembly but all of my 50Trx

    How to Replace serpentine belt 2008 Nissan Altima ...

    ? 11:29
    https://www.youtube.com/watch?v=5NchA85pnAE
    Jul 2, 2014 - Uploaded by nivekoch
    How to Replace serpentine belt 2008 Nissan Altima In this video i'll be going ... 2005 Nissan Altima 2.5L serpentine belt tensionerreplacement ...

Dec 16, 2015 | 2008 Nissan Versa

1 Answer

How do you change tail light bulb on 1997 Dodge Intrepid?


In the trunk. You will find black plastic wing nuts that hold the felt panels in place, remove and pull back the panel pieces and you can now access the taillight assembly, if you can't access the bulbs from that point you need to remove the tail lights by un bolting the 10mm nuts holding the taillight assembly then remove the taillight from the car now on the outside you should be able to access the bulbs from there by turning the bulb plugs about a 1/4 to a 1/2 turn, reassemble the taillight and interior panels.

Aug 28, 2014 | 1997 Dodge Intrepid

1 Answer

How to replace a brake light on a 2007 nissan maxima



  1. First thing you need to do is open the trunk.
  2. Remove the cargo net hooks. You do this by pulling the center out then pull the entire hook out.
  3. Now pull the carpet towards the front of the trunk (back by the rear light) back a little ways exposing.
  4. Now you will see some wire harness clips on the back of the trunk.
  5. Remove them to expose the three 10mm bolts.
  6. Remove the three 10mm bolts.
  7. Now you pull the whole light assembly out and this will expose the sockets that will allow you to change the bulbs. Unlike many cars where you have a bulb socket accessible from the trunk with this car the entire assembly must be removed.


  • Hope this helps and thank you for using FixYa.

Regards, Tony

Jul 27, 2011 | Nissan Maxima Cars & Trucks

1 Answer

How do i change the stop light blub on my 2007 versa hatchback


Hi there,

Inside the trunk/hatch area, directly behind the tail light assembly, are two plastic cover plates. Remove these with a flat tool (screwdriver will work) by prying in the small ****. They pop off. Inside one you will see a nut. This is a 10mm deep socket. NOTE: This nut is very easy to lose once loosened! If at all possible use a magnetic socket. If one is not available, loosen but don't remove completely. Use a magnet to remove. In the other compartment you will see wires on a plastic holder. This holder is snapped over the nut you need to remove (note you may see two, you want the one closest to the access opening). Use a flat (screwdriver) to slip the white cover with wires off the screw post. Use a 10mm wrench to loosen, then remove by hand. From the outside, pull the lamp assembly backwards. If necessary apply a little pressure on the interior screw posts. ACCESS TO LAMPS! Reverse procedure to reinstall. Note on the exterior there is a slot at the front of the lamp assembly when reinstalling. Good Luck!

I followed the advice above but have a few details to add. I used a stick (7/8" x 5/8" x 6") to push on the bottom post and then used a flat stick, actually a paint stirring stick, as a shim between the lens and the car body. With the shim in place I then used a flat nylon strap (a dog leash) which I placed around the tip of the lens, closest to the front of the car. I put both ends of the leash in one hand in order to pull on one side and then used my finger tips on the other hand to pull on the part of the lens closest to the bumper and applied even pressure straight back until the lens popped off allowing access to the light bulbs.

Hope this helps...

Jan 24, 2011 | 2007 Nissan Versa 1.8 Sl Hatchback

1 Answer

Can not understand how to change tail light bulb on nissan Versa.


The whole tail light assembly must be removed.Pop out 2 plastic covers near the tail light in the trunk. inside there are 2 bolts,one at the top and one near the bottom..Use a 10mm long socket,1/4 inch, with about an 6 inch extention on it.One of the bolts ( top, is off center) I put some heavy grease in the socket to hold the nuts from falling off when they come are off,so they don't fall behind the plastic wall..After you get them off,this is the "trick to remove the whole assembly without breaking it.It is very tight and hard to remove it due to a cliip at the front ,forward part of the light assembly.on the outside front,on the fender,Squirt some WD-40 on the pointed top part of the plastic light housing,letting it run down behind the housing on the outside. It has a clip in behind it on the fender.If you don't lube it ,it is very hard to release..Now I used the open end of a 1/4 inch socket extention to push on the lower bolt,inside the trunk,and you will see that the light housing will start to come out.do not force it.Get a piece of thin,strong string and make a loop out of it.Tuck the string behind the pointed tip of the housing,on the front part of the fender,so it will help pull the housing STRAIGHT BACK,while pushing on the bottom bolt inside of the trunk.This gives you 2 pressure points to pull and push out the housing.if you don't do them evenly,at the same time,you may end up breaking off the corner outside piece on the fender.If you bend it,it may break the plastic.
I know this sounds complicated when you first read this,but it WILL work,without damaging the tail light housing !!!
The dealer would probably charge you at least $ 50 to $75 to do this job.I am from Canada and I hate the Nissan dealerships.They don't want you to do ANY maintenance by yourself...
GOOD LUCK !!!

Aug 15, 2010 | 2007 Nissan Versa 1.8 Sl Hatchback

1 Answer

How do I change the back stop light


in the trunk or the 3rd brake light? trunk: remove the carpet cover, then 10mm bolts or wing nuts, pull tail light assembly out, twist bulb to remove. 3rd light. lay on your back in the trunk, locate and remove 2 10mm nuts, crawl into back seat pull up on housing. there will be a long plastic tab that will prevent you from pulling the housing all the way out, you can cut this and make this procedure easier, or remove the entire hat rack.

Apr 24, 2010 | 2007 Hyundai Sonata Limited Sedan

1 Answer

How di i get the tail light assembly of to change the brake light bulb on nisson versa hatchback


open the rear hatch and pull carpet away from the lens you want out,you will see four plastic thumb nuts,remove them and pull lens assembly out and replace your bulb

Jan 22, 2010 | 2007 Nissan Versa 1.8 Sl Hatchback

1 Answer

Replace tailight in 2007 nissan versa hatchback


Open the hatch and locate the 2 plastic covers, behind the tail light area on the inside panel. Remove these covers and the nut (8mm) behind them to access the light assembly. Pull lightly on the light assembly to remove, then replace the bulb.

Aug 11, 2009 | 2007 Nissan Versa 1.8 Sl Hatchback

1 Answer

How do you remove the tail light assembly to replace a bulb?


Inside the truck bed there are two bolts behind the tail light. You will need a 10mm socket to remove them. Remove them and the tail light assembly comes out and then twist the bulb connector and the then you can change the bulb.

Jul 15, 2009 | 1994 Nissan Pickup

2 Answers

How to remove the tail lights from a 2003 murano


Here's the step by step procedure from the beginning.
  1. Carefully remove the black one inch wide plastic molding strip that runs along the interior side of the tail light. This can be pried off carefully without breaking the plastic clips that hold it in place.
  2. Using a 10mm socket, remove the two bolts that you see which secure the tail light housing.
  3. The tail light housing is also held in place with three or four plastic clips which can be broken rather easily if you don't do this next step carefully. Begin prying the plastic tail light using a plastic putty knife or screwdriver. The top clip comes out pretty easily and so does the bottom one.
  4. On a cold winter day, the middle clip is the one that can break rather easily so gently rock the tail light or wait for warm weather when the plastic isn't brittle.
  5. Once the tail light "bucket" is removed it's a simple matter to replace the bulbs.
d87baef.jpg

Oct 03, 2008 | 2003 Nissan Murano

Not finding what you are looking for?
Cars & Trucks Logo

679 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...