Question about 2007 Chevrolet Impala LS Sedan New Cars

2 Answers

I just bought a 2007 impala ss,can't get rim off?

I didn't get manual and I have it jacked up bolts and rim still some how still very tight? I know it's probbably easy but I was out there for thirty minutes and got nowhere fast, is there a trick to it or something?

Posted by on

  • b_beatty May 31, 2009

    I don't think it's seized theres no rust and it dosen't even move? I figured there was a trick or somthing under center cap that locked it on or something?

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Leave tire on ground BEFORE you break the lugs loose,then jack it up.tire on ground will hold wheel from turning while you break lugs loose.then jack it up to change .also, put lug nuts on snug,lower to ground ,then tighten to specs,90-100psi.

Posted on Jul 17, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,392 Answers

Are you trying to get the rim off? Hard to understand from what you have written. Spray some WD-40 or similar in the stud holes. Let sit for a few minutes, then smack the inside of the wheel with a hammer to break free.

Posted on May 31, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cant get tire off on 2003 toyota matrix


tire off rim
wheel/tire rim off axle?
what? are you skinning tires off rims?
lug bolts too tight, ? (a disease of all tires shops this)
my wild guess is, you meant the lug bolts are too tight.
if yes, are all of them like that, ????
if yes, that means , they put them on too thight
my car is 60-80 flt/lbs the dig bulbs at the local tire shop use
and impact gun at 150. so they never see me again. ever.
i do most work my self even at my old age, but i never skin tires.
did that by hand at 19yo but not now.
take them off and then put them back at the spec torque
some dinky cars like these can warp the rotors set too tight.
the operators guide in every car, made shows the spec, read it.
lost the guide, bingo here it is
http://justgivemethedamnmanual.com/toyota/toyota-camry-owners-manuals/

read page.351, 76 ft-lbs, foot - pounds, use THAT.
i use antisieze lube on mine, for 50 years.

Feb 02, 2014 | 2007 Toyota Camry

1 Answer

Back pass side tier is wobaly. can u help?


The Tire may become wobbaly if it has not been tighten down properly or if some of the bolts that hold it on have become lose or broken.

I would suggest you jack the car up just enough to take most of the weight off the tire but not all the way up. You want to be able to tighten the bolts down without the tire spinning on you but still be able to get the bolt to tighten the Rim (Tire) down all the way.

Check all the bolts to be sure they are not broken. If they are broken you will need to replace them. If the bolts are ok then tighten them down but be sure to start at the top one. Then tighten the opposite bolt, never the one beside the one you just finished but always the opposite bolt. Tightening the opposite bolts until all the bolts are tight will allow your Tire (Rim) to be tightened evenly and should stop the wobble.

Another thing to look for is a loose hub cap giving just the apperance of a wobbely tire but it is just a lose hub cap.

If you have driven through a pot hole or over a curb recently then you may have damaged the Rim the tire sit on or the tire itself and that would mean the tire or rim would have to be replaced.

Lastly you may have a worn out ball joint. In this case it would need to be replaced by a shop as it is very difficult to do if you do not have the correct tools.

Jun 19, 2011 | 2001 Chevrolet Impala

2 Answers

Rim will not come off


put 1 lug nut on a few turns do not comletely tighten and hit tire on inside with a mini sledge hammer do not hit rim, if you have aluminum rims this happens because of the oxidation and gets stuck on the brake rotor

Jan 30, 2011 | 2004 Dodge Durango

1 Answer

I have a 2005 chevy impala and want to know the bolt pattern and the length apart of each bolt & can i put 20 inch rims on it?


Your best bet is to go to local tire store and pose this question.

The bolt pattern is one thing, but fender / body clearance for a much larger wheel is another matter altogether.

Jan 30, 2011 | 2005 Chevrolet Impala

1 Answer

Whining noise from front of 2003 impala.higher


Sounds like it could be the wheel bearing. Jack up the car, and see if the tire feels loose when pushing in and out at the top and bottom of the tire. That;s the most obvious way to check. But many times, the bearing is tight, but still bad.

May 13, 2010 | 2003 Chevrolet Impala

1 Answer

How to replace a turn signal light on a chevy impala 2007 ss


Open hood. on top of headlight assembly you will find 2 small bolts. I believe a 10mm. socket should fit. Take the 2 bolts, out and remove complete assembly.

Feb 01, 2010 | 2007 Chevrolet Impala LS Sedan New Cars

1 Answer

2007 Impala SS with 30,000 miles mysteriously jumps from cd/aux to radio...


Do you have the steering wheel controls? If so, my guess is the "source"button on the steering wheel control maybe sticking. If I remember, I'll look at my Impala and see if the contol can be disconnected at the steering wheel.

Jul 07, 2009 | 2007 Chevrolet Impala LS Sedan New Cars

1 Answer

Changing brake pads


jack up car put on jack stands remove the ground cable from battery.take the wheel off the side your working on.take out the two bolts that hold the calaper on and bump it off with a hammer.depress the caliper with a 6in c clamp and put new pads in and put back together.go to other side same thing.

Feb 21, 2009 | 2002 Chevrolet Impala

Not finding what you are looking for?
2007 Chevrolet Impala LS Sedan New Cars Logo

Related Topics:

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...