Question about 2001 Dodge Ram 1500 Truck 2WD

1 Answer

2001 Dodge 1500 5.2L V8.

Truck runs at idle but stalls when put into gear. The check engine light is also on. I do not drive the truck alot but want to get it running so I can sell it. It has 63000 miles on it. Any ideas?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 35 Answers

Fuel filter could be clogged.

Posted on May 31, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My truck will not stay running when I let off the gas.


If you have recently replaced the battery, disconnected the battery or had to jump start the dodge, you have likely reset the electronics.

The result of this reset is that the engine control module needs to relearn the running parameters including the idle point.

It take several minutes of idle/driving to reset the baseline parameters and during this interval keeping the engine from stalling is a challenge.

Hope this helps? Engine Stalling After New Battery Fix It Like Pro

Nov 17, 2016 | Dodge Cars & Trucks

2 Answers

1997 dodge ram 1500 4x4 abs light on runs fine idles good but put it into gear wont go past 35 mph engine running smooth even at 35 mph


Bernard's Blog: Dodge Transmission Output Speed Sensor

bernardsblog.blogspot.com/.../dodge-transmission-output-speed-sensor.h...
Sep 8, 2009 - My 99 Dodge 2500 Ram won't accelerate..transmission is NOT slipping,.... It has been running fine and the check engine light even cleared itself yesterday.... So it wouldn't go into first gear and then 3 minutes later my check engine ... I have a1997 Dodge Ram 1500 with a 5.9L instead of the stock 5.2L. It ...

Dodge Ram Idle and Stalling Problems - Car Forums at Edmunds.com

forums.edmunds.com > Dodge > Dodge Ram Pickup 1500

Aug 17, 2011 - 30 posts - ‎25 authors
Learn more about Dodge Ram Pickup 1500 at the Edmunds.com ... The crank sensorwas put on however it started stalling again. ... The truck starts fine, but will only runat 2000's RPM and only then if .... Then as I start driving about 1/3 of a mile go dead again, I knockout of gear, crank back up immediately.

WILL NOT GO OVER 30MPH WITH PEDLE TO METAL ...

repairpal.com > Questions > Dodge > Charger > 2006 Dodge Charger
I WAS DRIVING FINE AND THE CAR ACTED LIKE IT GOT STUCK IN ... Then the transmission didn't want to change into 2nd gear. .... Whenever i start up my car theabs and esp light turn on and when i try driving it doesnt go over 30 mph even .... in neutral but not it just wont go up hills and i think it has something to do with

Jan 07, 2016 | Dodge Cars & Trucks

1 Answer

I own a 1989 dodge d100 3.9v6 automatic it starts and runs but when put into gear it just stalls out?


Does it happen when you shift just to 1st
what is idle in park
when you turn on the ac in park does the idle go up a hair??

May 01, 2014 | Dodge D150 Cars & Trucks

1 Answer

2008 Sprinter stalls at idle when in gear


2506 PCM/ECM Power input signal range/performance
110 IAT Intake Air Temp sensor 1 circuit
104 MAP/ Baro sensor low input
You probably did do some damage by not isolating the engine and controls out before the repairs/mods were started.

Jun 11, 2013 | 2006 Dodge Sprinter

2 Answers

PO700 PO740, check engine light on. Run a test on


PO700 is a code telling you there are codes in the TCM of some late model cars where the Transmission control module has lost connection to the PCM the vehicals main computer , And basically it happens when the TCM has a issue within itself or the transmission that sets a code and it sends a request for the PCM to illuminate the SES or CHECK engine light.
PO740 is a chrystler specific code that involves your Tourqe Converter Clutch Circuit (specifically The TCC solenoid) this code if not repaired quickly could cause major transmission problems....slipping out of gear....not shifting from first to second properly and just all around trans problems...eventually leading to no shifting at all...I highly recommend fixing it soon.

Feb 22, 2010 | 2001 Dodge Caravan

1 Answer

2001 Dodge Ram Magnum 360 gas stalling also!


1.Start by changing plugs and wires. 2.Check for vacuum leaks. With the engine running, wigglr every hose you can see, to make sure nothing is loose or cracked. 3.Change fuel filter. 4.Check timing. 5.Check air control valve. 6.Check idle control sensor.

Jun 15, 2009 | 2001 Dodge Ram 1500 Truck 2WD

2 Answers

Won't run/ misses badly in gear


timing chain needs to be changed out

Dec 25, 2008 | 1989 Dodge D150

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

250 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...