Question about 2000 Dodge Durango

1 Answer

Ihave to put the plug wires back on the distributor.

I had to replace the dist. cap and rotor and had it apart too long to remember where the plug wirs go. Please help.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 318 Answers

What motor do you Ihave to put the plug wires back on the distributo - graphic.aspx?mod=reptiff&module_id=1&session_id=%7bb0f3ecb7-e6d5-4126-975a-5453758a764a%7d&image_guid=95c27013&print_bw=0&

Posted on May 31, 2009

  • Jeffery Lewis
    Jeffery Lewis May 31, 2009

    i sent you the firing order for 5.2 and 5.9 liter engine

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1985 VW Cabriolet won't start turns over have power to top of cap-coil but no spark from plugs has new cap-rotor and coil any ideas?


It is hoped you have replaced the wires that go from your distributor cap to each of your spark plugs AND that the gap on your plugs are set correctly.. Secondly, if you replaced your rotor head, and it is not sparking, it is very possible your rotor isn't making the connection inside the dist. cap.

the only way to verify this is to get your old rotor and put it back on. If it fires, you know your replacement part isn't configured properly.

Aug 16, 2017 | Cars & Trucks

1 Answer

Replaced the distributur ran but barly tryed to rotate the dist but ran out of room. pulled out and rotated then reinstalled now wont start. Help : )


Take out #1 plug if possible. put straw or something similar in plug hole on top of piston, put a wrench on crankshaft pulley nut and rotate engine. when piston gets to the top it should be on tdc. and rotor pointing to #1 wire on distributor cap. replace plug and adjust dist, if piston is on top, and dist, is off. pull dist so the rotor button points to #1. GOD-bless! OR YOU CAN ALSO ALIGN THE TDC MARK ON CRANKSHAFT DAMPER.

Aug 02, 2015 | 2000 Nissan Xterra

1 Answer

How do I find the timing marks on a 1992 voyager


Sounds like you replaced the distributor without setting #1 at TDC? The distributor cap should indicate which plug is the #1 plug wire. If there are no inspection plugs you can pop out to see the timing marks on the camshaft gears you will need to disable the starting system (fuel flow) remove #1 plug and turn it over until #1 piston is at TDC on the compression stroke. Then insert the distributor cap with the rotor on it, taking note of where the #1 plug tower is on the cap. Once the dist is installed place the cap on and make sure the end of the rotor is aligned with the #1 tower inside, if it is your good to go. If not take the dist out and turn it a bit left or right then put it in again until it lines up correctly (may take a few tries). Once aligned secure everything, replace spark plug and it should fire up.

Jan 25, 2015 | 1992 Plymouth Voyager

1 Answer

Replace the distirbutor


Disconnect the battery. take cap off but leave wires intact. Check position of rotor for reinstalling. Loosten bolt under distributor and take out. Lift didtributor and turn rotor counterclockwise to remove dist. Make sure you put back in same identical spot.or vehicle will not run. Mark spot on motor where rotor is if you can't remember. You have to turn rotor counterclockwise to have dist. fall back into same spot. Will be tough to get out at first. Don't spray with penetrating oil. Just pull up and turn.

Jan 19, 2013 | Chevrolet Blazer Cars & Trucks

1 Answer

94 royal begis to cut out, chugs at about 55


Replace the spark plugs and wires along with a distributor cap and rotor. Be careful to leave the old wires and plug wires connected to dist.cap, just remove dist. cap from the distributor and lay aside with plug wires on it then install rotor then new cap and proceed to replace each wire for cap and spark plug one at a time so you don't mix up the spark plug wire firing order. Cap laying to the side is used for reference purpose.

Feb 26, 2010 | 1994 Oldsmobile 88

2 Answers

How to replace distributor on a 2001 volkswagon cabrio


remove disturbutor cap mark where rotor is and mark position of dist, remove bolt holding dist, pull dist out. now install new one but make sure rotor ends up pointing in exact poistion as old and dist is postioned they same. good luck.

Oct 25, 2009 | 2001 Volkswagen Cabrio

1 Answer

1993 ecilpse 1.8 eng no spark. there is 12v at the dist


So you have voltage at the distributor and the rotor is turning. Check for voltage at the end of each plug wire. If you do not have voltage there you are loosing it in the wire or the cap. Is the cap new? Are cap and rotor new?
Just be sure you have voltage at every point between the distributor and the plugs.
Good luck!

Trevor Marsh

Jul 02, 2009 | 1993 Mitsubishi Eclipse

1 Answer

I have to put the plug wires back on the distributor.


okay remove your driverside sparkplug the one closes to the front this should be #1 piston put a screw driver in the hole but dont let it bind, slowly click the starter until the srew driver come up all the way up this is top dead center TDC now look at the rotor and where the cap lines up this #1 second is#8 piston on the pass side closes to the fire wall or cab so, on the engine #1 piston234 onthe driver side 5678 on the pass side and in order on the cap it should be 1 8 4 3 6 5 7 2 also make sure you didnt drop the dist in wrong and hav it 180 degrees backwards dont get frustated stop and try again later also make sure this is the right firing order for your dodge i gave you a chevy fire order but i am almost positve this is the order for all v8s

Jun 02, 2009 | 2000 Dodge Durango

Not finding what you are looking for?
2000 Dodge Durango Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8265 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...