Question about 2005 Ford Focus

1 Answer

Tinting the rear door glass geting to the edges

Tinting rear door glass on cmax how to get to the edges

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Ford Master
  • 450 Answers

Usually make cut out template of window then cut tint to template then fit and work into tight spots while fitting.New sharp razor blades and a steady hand.

Posted on May 31, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rear door glass broken out, need to know how to get new glass in


To get new glass for your car, you can take a look on QualityTire Auto Shoppe for Wheels Tires Rims Auto Tint from where you will surely get collection of car accessories. Quality Tire auto shoppe also providing services on car window tinting.

Mar 05, 2014 | 1998 Buick LeSabre

1 Answer

Rear door glass removal


After you get the regulator assembly out of the way try removing any tracks inside the door that can be removed and see if you can then rotate the glass.

Jan 16, 2014 | 2009 Dodge Journey

1 Answer

1998 ford explorer rear window removal


Hi there:

  1. Remove the door trim panel and speaker if applicable.
  2. Remove the screw from the division bar. Remove the inside belt weatherstrip(s) if equipped.
  3. Remove the 2 vent window attaching screws from the front edge of the door.
  4. Lower the glass and pull the glass out of the run retainer near the vent window division bar, just enough to allow the removal of the vent window, if equipped.
  5. Push the front edge of the glass downward and remove the rear glass run retainer from the door.
  6. If equipped with retaining rivets, remove them carefully. Otherwise, remove the glass from the channel using Glass and Channel Removal Tool 2900. Remove the glass through the belt opening if possible.

To install:
  1. Install the glass spacer and retainer into the retention holes.
  2. Install the glass into the door, position on the bracket and align the retaining holes.
  3. Carefully install the retaining rivets or equivalent.
  4. Raise the glass to the full closed position.
  5. Install the rear glass run retainer and glass run. Install the inside belt weatherstrip(s).
  6. Check for smooth operation before installing the trim panel.



Hope this helps.

Feb 28, 2013 | 1998 Ford Explorer

1 Answer

How do I take the front window out of a junk yard 1992 cadillac sedan de ville ( no battery) without riping the tint?


I would worry about saving the glass from breakage. The tint will get scratched no matter how its removed. By the way most states ban tinted windows on the front doors of all vehicles. That is why the rear windows from the factory are tinted with the exception of Wisconsin. They ban tinted windows period

Jan 16, 2011 | 1992 Cadillac DeVille

1 Answer

I need to remove a rear door gllass on a lexus Gs


Remove rear door panel, reconnect power window switch, looking at bottom edge of glas you should see two 10mm bolts roll down window until bolts are accessible. Remove bolts and tilt window around 10 degrees top edge out/in. if still to tight to slide out put glass in lowest position and remove window frame weather stripping and it should slide right out the top, careful not to scratch tint.

Aug 19, 2010 | 2009 Lexus LS 460

1 Answer

How do I remove the tint of my rear window in my 1998 chevy Malibu?


If it has a rear window defroster, you can't use a razor blade. If the tint material will pull off and leave glue behind, then spray windex on the glass and put the tint material back on the glass like it was. Can't do this in the sun to long, the sun will dry out the windex. The ammonia in the windex will loosen up the glue. Then you can remove the tint material, and the glue should wipe of with a paper towel.
p.s. let the windex soak for 5 min. or so.

Jun 27, 2010 | 1998 Chevrolet Malibu

1 Answer

How do I remove and install a rear passenger side window (manual) in a 1997 Saturn SL1?The window was smashed, and I need to replace it. Thank you so much for your time and help!


Saturn Coupes/Sedans/Wagons 1991-1998 Repair Guide
Door Glass and Regulator - REMOVAL & INSTALLATION
(see Figures 1, 2, 3 and 4)
  1. Remove the outer door panel assembly. Refer to the sub-procedure under Door Locks, earlier in this section.
  2. For rear doors, loosen the bottom fastener of the rear door stationary window assembly, in order to provide clearance, then apply tape to the lower half of the outboard exposed portion of the stationary window channel. The tape must be applied in order to prevent damage to the paint surface.
  3. Lower the door glass, then use SA9148B, or an equivalent tool, to remove the glass nuts. Push the glass upward and rotate slightly, then remove the glass from the vehicle.
  4. If the regulator is also to be removed, proceed as follows:
    1. Remove the inner door trim panel. Refer to the procedure earlier in this section.
    2. If applicable, unplug the wiring harness from the power regulator.
    3. Except for the rear door, remove the regulator cam bolts.
    4. Drill out the regulator rivets and remove the regulator from the vehicle.
To install:
  1. If removed, install the regulator to the door assembly:
    1. Position the regulator to the door and secure using rivets.
    2. Except for the rear door, install the cam bolts.
    3. If applicable, connect the wiring harness to the regulator.
    4. Install the inner door trim panel to the vehicle.
  2. Install the door glass into the door and over the regulator studs.
  3. Install the glass nuts using tool SA9148B, or equivalent.
  4. Check the door glass for proper operation and alignment.
  5. If necessary, adjust the glass alignment. For rear doors, fore/aft adjustments are made after loosening the B bolts, while in/out adjustments are made when the A bolts are loosened.
  6. Except for the rear doors, glass which is not running parallel to the door header may be adjusted after loosening the inner panel cam attachment bolts and adjusting the cam. If the glass is floating in the opening, lower the glass 3 / 4 downward, loosen the front guide fasteners, push the glass rearward to seat it in the rear channel, then bring the front glass guide back to the front edge of the glass. Apply a light finger pressure on the guide and tighten the fasteners.
  7. Once the glass has been properly adjusted and is operating smoothly, install the outer door panel assembly.
cc80642.jpg

Fig. 1: Remove the glass nuts using a suitable tool-front door shown

8ca6a10.jpg

Fig. 2: Exploded view of the regulator mounting-except rear door

b18d064.jpg

Fig. 3: Exploded view of the rear door regulator mounting

0b9470a.jpg

Fig. 4: Adjustments of rear door glass are made after loosening the A or B bolts


I hope help with this (remember rated this help) Good luck.


Oct 16, 2009 | 1997 Saturn SL

2 Answers

Windows tint


If it's factory tint, it is imbedded in glass and can't be removed.
If it's add on tint, it is just a plastic film on inside of glass.
Call a tinting shop and ask what chemical to spray on film to soften adhesive, or ask for removal quote too

Aug 26, 2009 | 2002 Mercedes-Benz C-Class

2 Answers

Fitting an isofix car seat in a ford cmax 57 plate tdi


if there are a small part of the backseat (ca 10 cm high located at the bottom of the back) that can be picked out, you have isofix points.
if your backseats are in one pice, theres not

Apr 11, 2009 | 2007 Ford Focus (3 Door) Hatchback

1 Answer

Side windows


It may seem easier to tint them out of the suv, but it is very easy to damage them putting them back in. pre-cut the tint material on the outside of the glass. Make sure you have the tint on the correct side when pre-cuting. leave a 1/32 gap around the tint edge when pre-cuting. That will keep the tint from binding up around the edges. Also the soapy water has a way to escape. Make sure the glass is as clean as possible.

Feb 07, 2009 | 1987 Toyota 4Runner

Not finding what you are looking for?
2005 Ford Focus Logo

Related Topics:

123 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...