Question about 2004 Ford Focus

1 Answer

Front headrest, ford focus

Any idea how i can remove these?, it says in the owners book, to 'consult an expert'. Seems a bit extreme as im only fitting some seat covers

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 93 Answers

Seat Backrest — Front front headrest, ford focus - adobe.gif Printable View (404 KB) Disassembly
All vehicles
ani_caut.gif WARNING: Always wear safety glasses when repairing an air bag supplemental restraint system (SRS) vehicle and when handling an air bag module. This will reduce the risk of injury in the event of an accidental deployment.
ani_caut.gif WARNING: Never probe the connectors on the air bag module. Doing so can result in air bag deployment, which can result in personafront headrest, ford focus - ani_caut.gif>
ani_caut.gif WARNING: Front seat back trim covers installed on seats equipped with side air bags cannot be repaired, they are tofront headrest, ford focus - ani_caut.gif. Cleaning is permissible.
ani_caut.gif WARNING: To reduce the risk of personal injury, do not use any memory saver devices.
NOTE: If a seat equipped with a seat mounted side air bag and/or a safety belt pretensioner (if equipped) system is being serviced, the supplemental restraint system (SRS) must be depowered.
NOTE: The air bag warning lamp illuminates when the RCM fuse is removed and the ignition switch is ON. This is normal operation and does not indicate a supplemental restraint system (SRS) fault.
NOTE: The SRS must be fully operational and free of faults before releasing the vehicle to the customer.

  1. Depower the SRS. For additional information, refer to Supplemental Restraint System (SRS) Depowering and Repowering in the General Procedures portion of Section 501-20B.
  1. Remove the head restraint.
  1. Remove the head restraint guides.
    • Using a suitfront headrest, ford focus - e0008398.gifiver, depress the locking tang.
    e0008398.gif

Posted on Jun 02, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove drivers side headest from 1992 ford Taurus gl


remove drivers side headest Diana, If all else fails pop into a garage and they can show the procedure. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."

How To Remove Front Seat Headrests Repair Loose Headrests

Headrest Removal

1992 ford Taurus remove drivers side headrest Google Search

Apr 07, 2016 | Ford Cars & Trucks

1 Answer

How to remove serpentene belt in a 2003 ford focus


There are 6 possibilities, here are the 3 engines with A/C...

zjlimited_1533.jpg

zjlimited_1534.jpg

zjlimited_1535.jpg

Consulting your owner's manual should give you an idea of how to replace a belt depending on which belt it is that needs changing. Assuming it is the timing belt that needs to be changed it is a simple process to undertake, though if you are unsure of working on motor cars it may be better to take the vehicle to a garage for professionals to carry out the work.

Firstly check your owner's manual for the recommended mileage for replacing your timing belt. Replacement for a Ford Focus is at 120,000 miles. You need to locate the timing belt and examine it for breaks, damage, fraying, worn spots or looseness.

Disengage the negative battery cable in all models. Detach the passenger inner splash-shield and wheel cover, the accessory drive and timing belts, the tensioner and the crankshaft pulley. Remove the spark plugs, catalytic converter and idler pulley in 2000 and older Ford Focuses. Undo the retaining fasteners and lift the timing belt cover off the engine. Align the crank and camshaft timing marks. Older models call for undoing the water pump pulley and valve cover before locking the camshaft in place. Release the tensioner's bolt. Turn the arm to the right 14 degrees and place a 1/8 inch drill bit in the opening. This secures the belt tensioner in place; you can now take the belt off.

Once you have fitted the new belt you can re-assemble the parts which have been removed in the reverse order.

Hope helps.

Jul 03, 2011 | Ford Focus Cars & Trucks

1 Answer

How do I remove the headrest from a 2006 ford focus?


Most times there is a small hole on the plastic piece that the heads go in and out of. This hole is big enough to put a small nail or paperclip in. Doing so and pressing firmly, will trigger the release switch. You might have to press in on that, and the regular button (for going up and down) at the same time, and have a 2nd person pull up on the headrest.

Here is a link to some basic install instructions, which covers headrest removal with pictures:

http://www.seatcoversunlimited.com/Insta...

Good Luck please rate 4 thumbs up and please leave a testimonial

Oct 30, 2010 | 2006 Ford Focus

1 Answer

Can the 2010 Navigator replace the 2010 Expedition headrest? It seems that the Navigator has the same seat design a.s the Expedition Limited and the headrest is adjustable, as where the Expedition it is...


Finally found someone after 40 years, that believes a 5th grader could design a vehicle.
I have told my wife, that I would fire most all design engineers,ever hired since 1960. You can't even remove an oil filter, for the last 45 years,let alone see it.
I have 47 years,some professional, and can't believe what these maufactures are thinking.
Iam about to do a ground up 60's resto, and never drive drive a high tech vehicle again. And I understand the technology and have no problem repairing them.

Sep 20, 2010 | 2009 Ford Focus

1 Answer

What is the symbal like a open book


When you see this symbol, it is imperative that you consult the relevant section of this guide before touching or attempting adjustment of any kind ... mean, check the Owners Guide.

Here can find it and download: Ford-Focus Owners Manual

Hope helps (remember rated and comment this).

Aug 12, 2010 | 2001 Ford Focus

2 Answers

Removing the headrest on a 2000 ford mustang gt


1. Lift headrest and headrest support bars trim all the way up.

2. Insert tongue depressor (or slim jim) down the front side of the headrest bar. Push depressor down as far as possible. When the depressor is beneath the headrest trim piece, push headrest all of the way down.

3. Lift headrest to remove.

Jul 05, 2010 | 2000 Ford Mustang

3 Answers

Can the headrest for a 2010 ford expedition be replaced with an aftermarket so not to have that angle?


I know five (5) people who purchased the 2009 or 2010 Expedition. All 100% of them have complaints of the headrest hurting their neck. I know folks that won't even drive their new 2010 Expedition because it hurts their necks, and the dealer won't take it back! If enough people tell ford about the problem, erhaps Ford will post a Technical Service Bulletin (TSB) to tell dealers how to fix the problem. It is possible to build safe headrests that do not hurt necks during normal driving: just look at the competition. The headrest is not the right equipment to sacrifice comfort. Neck pain causes distraction and is a safety issue. Ford should be as concerned about liability from wrecks caused by headrest pian distractions as they are about the rear impact safety. Complain to Ford!

Dec 11, 2009 | 2009 Ford Focus

1 Answer

The angle of the headrest is too far forward on 2010 ford focus


try cleaning battery connections and starter connections if this does not help check timeing may be out. check nfor possible over heating. berrydalewolf

Oct 26, 2009 | 2009 Ford Focus

1 Answer

Cannot remove back seat headrests for 98 328i


Im doing the same thing.. Push the headrest full forward, then lift hard to get past last indent in pole.. This worked for the front as well.. i also could not find a hole to push

Apr 05, 2009 | 1998 BMW 3 Series

2 Answers

Ford focus 04, handbrake light stays on when driving but faded


make sure u are not low on brake fluid,this will also illuminate the red brake light.

Feb 11, 2009 | 2002 Ford SVT Focus

Not finding what you are looking for?
2004 Ford Focus Logo

495 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5474 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...