Question about Hyundai Motor 2002 Elantra

1 Answer

How to change rear brake pads

How do change brake pads on my hyunda elantra

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 776 Answers

Raise the rear of the vehicle and make sure it is securely supported. Remove the rear wheel Remove the brake hose (A) from the suspension arm by removing the brake hose clip (B).Thoroughly clean the outside of the caliper to prevent dust and dirt from entering inside.Support the caliper with a piece of wire so that it does not hang from the brake se.how to change rear brake pads - f2d9a24.jpg
Remove the two guide rods (C) and caliper (D) from the bracket. Remove the pad shim (A) and brake pads (B).77fcb0a.jpg

Remove the pad retainerhow to change rear brake pads - 2884b28.jpg"http://i.fixya.net/uploads/images/2884b28.jpg" alt="2884b28.jpg" class="h_mi" />
Clean the caliper thoroughly; remove any rust, and check for grooves and cracks. Check the brake disc for damage and cracks. Install the pad retainers. Check the foreign material at the pad shim (A) and the back of the pads (B). Contaminated brake discs or pads reduce stopping ability. Khow to change rear brake pads - 3fdca95.jpgoff the discs and pads.3fdca95.jpg
Install the brake pads (B) and pad shim (A) on the caliper bracket. Install the inner pad with its wear indicator (C) facing down ward. If you are reusing the pads, always reinstall the brake pads in their original positions to prevent a momentary loss of braking efficiency. Rotate the caliper piston (A) clockwise into the cylinder, the align the cutout (B) in the piston with the tab (C) on the inner pad by turning the piston back. Lubricate the boot with rubber grease to avoid twisting the piston boot. If thehow to change rear brake pads - 1d2811d.jpgt is twisted, back it out so it is positioned properly.1d2811d.jpg
Install the brake caliper (D). Install and torque the guide rods (E) to proper specification. Install the brake hose (F) onto the suspension arm with the brake hose clip (G). After installation, check for leaks at hose and line joints and connections, and retighten if necessary. Depress the brake pedal several times to make sure the brakes work, then test-drive. Engagement of the brake may require a greater pedal stroke immediately after the brake pads have been replaced as a set. Several applications of the brake pedal will restore the normal pedal stroke.

Posted on Jun 02, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i change brake pads on a 2009 hyundai elantra


That was a close description but not exact. There are no "pins" that need to be removed. You can re lube the sliding pins the caliper bolts go into but they do not have to be removed to replace pads. The brake hose does not need to be detached and neither the front or rears on the '09 need to be "turned" in; they just push in. Some model years do turn to retract but not the '09.

The pads both front and rear are notoriously tight but work OK. I do lube them well. I do not use the OEM shims. Most replacement pads have shims attached.

Jan 13, 2012 | Hyundai Elantra Cars & Trucks

1 Answer

Parking brake 2005 elantra does not work


Hi Richard, I think you may find that the park brake works on a separate system with a set of small brake liners inside a drum on the rear wheels. If I'm wrong and it uses the disc pads, try replacing the pads and adjusting the travel, that should sort out the problem. Regards John

Nov 16, 2011 | 2005 Hyundai Elantra

1 Answer

What the best soultion for brakes locking up in the snow is there better brake pad to use for that


No, there are no different pads, you just have a very sensitve brake system in your car, try usung the emergency brake when driving in the snow. Slightly apply the emergency brake when you drive this will help balance the front and rear brake systems.

Oct 19, 2010 | 2005 Hyundai Elantra

1 Answer

How to change rear brake pads on hyundai elantra


you must squeeze the calipar PISTON back i use a G clamp to compress them!

Apr 14, 2010 | 2000 Hyundai Elantra

4 Answers

Rear Brake Pad - scam?


90% chance you are being scammed. This seems to be routine at a lot of franchise places i'm afraid.

Jan 06, 2010 | 2006 Hyundai Elantra

1 Answer

I hear a tapping from my right rear brake when I brake. Doesn't happen when I dont brake. I just replaced the shoes, drums and hardware. This was happening before i replaced all of this too.


dear friend:the tapping noise comes from the brakepads and it means that the anti rattle plates were not installed on the last brake pad
change

Sep 15, 2009 | 2001 Hyundai Elantra

1 Answer

Elantra rear brake replacement


hiya the rear disc brakes are as front disc brakes auto adjusting however the rear brake calipers pistons have to be wound back into the caliper to enable new pads to be fitted if you look at piston you will see they have either slots or holes in the surface this is for a sutable implement/tool to fit and then turned clockwise whilst pressing piston as you wind/rotate it back into caliper for your info there is a tool made for this purpose made by draper or seeley tools which makes job easy diy and cost £9--99 uk and can be bought from most auto stores ? however it is possible to manage with the spanner with horse shoe open end commonly supplied with circular hand saws the spanner is the one used for replacing blade? i have used this in past with success but now have the expensive univesal tool for the job hope this helps?

Dec 04, 2008 | Hyundai Motor 2002 Elantra

Not finding what you are looking for?
Hyundai Motor 2002 Elantra Logo

1,835 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...