Question about 1998 Plymouth Voyager

1 Answer

Back seat head rests, need to know where to buy them

I have a 1998 Plymouth Voyager, but the back seats doesn't have their head rests. I would like to know where I can buy them.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Plymouth Master
  • 6,674 Answers

Possibly at dealer but I would check recycle yard first.(wrecking yard.)

Posted on May 31, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fuel filter replacement 1998 plymouth voyager 3.3l


Should find it near center of fuel tank under vehicle below seats.

Jan 23, 2013 | 1998 Plymouth Voyager

1 Answer

Nocompressionvalve#6


not sure what you are asking, you found the problem ....the valve is not seated properly in its seat or the edge of the valve is burned or the valve seat has slipped out of place make sure you are on the compression stroke for that cylinder before condemning the valvetrain

Dec 07, 2012 | 1998 Plymouth Voyager

1 Answer

There is a broken hinge to raise and lower the back rest on my driver side seat . How does that get repaired? Does the entire seat have to be removed from the car? Or is there another way to make the...


you will have to remove the seat and the cover to access the hinge, it may just be welded. If it cant be fixed, maybe find one in a salvage yard, If its not the right color, the covers will need to be changed.

Sep 09, 2011 | 1999 Plymouth Grand Voyager

1 Answer

Which seats are safer for car seat the middle two seater or rear three seater?


The rear seat is optimal due to the passive restraint hook-ups you have in the cargo area, however any position other than the front seat will due as long as you install the carseat following the manufacturer's (of the car seat) directions.

Jan 14, 2011 | 1998 Plymouth Voyager

1 Answer

We need to remove the drives side head rest to install a seat cover, but we cannot figure out how to remove the head rest. How do you remove the driver's side head rest?


Head Restraints Removal
  1. Unscrew front seat head rest guide rod retainers (610A18) .
  1. Pull up on front seat back head restraint (611A08) . Compress foam in area of front seat head rest guide rod sleeves (610A16) .
  1. Remove front seat back head restraint positioning springs. Pull front seat back head restraint up and out.
Installation
  1. Slide front seat head rest guide rod retainers onto front seat back head restraint posts.
  1. Compress foam in front seat head rest guide rod sleeve area. Install positioning springs on front seat head rest guide rod sleeves .
  1. Insert front seat back head restraint posts (notches on posts facing rearward) into front seat head rest guide rod sleeves and push down to engage positioning spring.
  1. NOTE: Front seat back head restraint must operate smoothly throughout its range of travel, must remain in any fixed position, and must not be freely removable from the seat back. If any of these conditions are not met, check for proper installation of positioning spring onto front seat head rest guide rod sleeve .

    Tighten front seat head rest guide rod retainers onto front seat head rest guide rod sleeves .
  1. Adjust front seat back head restraint by applying hand pressure, either up or down, to center area of front seat back head restraint .

9a4d433.gif

Aug 21, 2010 | 1998 Ford Taurus

1 Answer

I am trying to put on seet covers for my 1999 plymouth voyager but they get stuck on the arm rests. Is there an easy way to take off the arm rests?


as i recall there should be a hole under the arm rest right were it connects to the seat should be 1 big bolt take it out and put back after you put on covers. you have to stick your finger in the hole to find the bolt

Aug 05, 2010 | 1999 Plymouth Voyager

1 Answer

Brakes


Sounds like a proportioning valve, it controls how the fluid is dispersed between the brakes.

May 07, 2009 | 1998 Plymouth Voyager

1 Answer

How do you remove the headrest on a 1996 ford crown victoria?


Head Restraints Each front seat is equipped with dual-post design front seat back head restraint (611A08). The front seat back head restraint is installed as follows:
  • It travels on dual posts which have notches to engage a spring-loaded catch in the guide.
  • The front seat back spring assembly retains the front seat head rest guide rod sleeve (610A16).
  • The front seat back head restraint is adjustable from its normal position to a raised position of approximately 25 mm (1 inch).
  • Pull up on the front seat back head restraint to raise it. Pushing down will return it to its normal position.
----------------------------------------------------------------------------------------------

Removal
  1. Unscrew front seat head rest guide rod retainers (610A18).
  1. Pull up on front seat back head restraint (611A08). Compress foam in area of front seat head rest guide rod sleeves (610A16).
  1. Remove front seat back head restraint positioning springs. Pull front seat back head restraint up and out.
Installation
  1. Slide front seat head rest guide rod retainers onto front seat back head restraint posts.
  1. Compress foam in front seat head rest guide rod sleeve area. Install positioning springs on front seat head rest guide rod sleeves.
  1. Insert front seat back head restraint posts (notches on posts facing rearward) into front seat head rest guide rod sleeves and push down to engage positioning spring.
  1. Tighten front seat head rest guide rod retainers onto front seat head rest guide rod sleeves.
  1. NOTE: Front seat back head restraint must operate smoothly throughout its range of travel, must remain in any fixed position, and must not be freely removable from the seat back. If any of these conditions are not met, check for proper installation of positioning spring onto front seat head rest guide rod sleeve.

    Adjust front seat back head restraint by applying hand pressure, either up or down, to center area of front seat back head restraint.

Mar 01, 2009 | 1996 Ford Crown Victoria

Not finding what you are looking for?
1998 Plymouth Voyager Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...