Question about 1999 Chrysler 300M

1 Answer

Changing inner tie rods

Im tryin to change the inner tie rods and i cant get leverge on the belt to even get it off. how do you do that in such small space from how the parts are positioned?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 323 Answers

Remove the wiper module assembly for more room. It will be the entire box the wiper motor sets in. Remove the wiper arms and cowl. From there you'll see what I mean (hard to explain from here). I hope this helps.

Posted on May 31, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

In replacing outer tie rods, should inner rods be change also?


The leak is not from the inner tie rod. It is from the rack and pinion. Racks come with the inner tie rods.

Jul 09, 2015 | Cars & Trucks

1 Answer

Inner tie rod removal with tool


One end of the tie rod is a left hand thread
make sure that you are turning it the right way

Apr 12, 2015 | 2005 Hyundai Tucson GLS

1 Answer

Have anyone out there ever change inner tie rods on a1995 honda odyssey?,if so simply explain,THANKS


Procedure on replacing the inner tie rod ends:


1) Raise and safely support the vehicle.

2) Remove the front wheel/tire assembly.

3) Clean the steering rod between the steering boot and outer tie rod end lock nut with a suitable penetrating lubricant and a clean cloth or shop towel.

4) Loosen the outer tie rod end locking nut 1/8 turn.

5) Loosen the steering boot clamp(s), and slide the small clamp off the boot.

6) Carefully loosen the boot and slide outward off the steering rack and onto the shaft to expose the inner steering rod mounting fastener.

7) If necessary, position the inner steering rack shaft in or out to allow for additional access.

8) Relieve the steering rod nut locking tab from the inner steering rack shaft, then loosen the steering rod ball socket nut 1 turn.

9) Matchmark the tie rod end to the threaded shaft.

10) Remove the cotter key and castle nut from the outer tie rod end threaded spindle, and using a tie rod end removal tool, remove the tie rod from the steering knuckle.

11) Hold the tie rod with a wrench, and remove the outer tie rod end from the threaded rod, counting the number of complete turns it takes to remove the tie rod end from the shaft. Write the number of turns on a piece of note paper.

12) Remove the tie rod end lock nut from the threaded steering shaft.

13) Slide the steering rack boot off the shaft.

14) Remove the inner steering rod ball socket nut from the inner steering rack shaft.

To install:

1) Inspect the tie rod end for looseness, and the steering rack boot and tie rod end boot for cracks deterioration or damage and replace as necessary.

2) Clean steering rack shaft and apply a light coating of Genuine Honda Power steering fluid as necessary.

3) Apply a medium strength locking agent to the threads where the inner steering rod ball socket mounts. Use a new locking washer and a new stop washer, and install the inner tie rod onto the steering rack shaft.

4) Tighten the inner tie rod end fastener by 58 ft. lbs. (78 Nm)

5) Peen the lock washer over the nut or onto the flat surface of the steering rack shaft.

6) Apply silicone grease to the outer circumference of the inner tie rod end ball socket, and onto the groove just outside of the socket.

7) Apply silicone grease to the inside of the small end of the steering rack boot, and slide the boot over the steering shaft and onto the rack and install the boot clamps. If the boot has air hose fittings make sure they are installed as removed.

8) Apply a light film of an anti-seize compound onto the threaded tie rod end, and install the tie rod end lock nut.

9) Install the tie rod end onto the tie rod, turning it in exactly the number of turns it took to remove it.

10) Install the tie rod end following the tie rod end installation procedure.

11) The balance of installation is the reverse of the removal procedure.

12) Check the front end alignment and adjust as necessary.

Sep 10, 2012 | 1995 Honda Odyssey

2 Answers

Need to replace inner tie rod on a 1998 ford ranger two wheel drive , driver side . engine size is 2.5. do i have to take outer tie rod off as well?


webbraymond2, Yes, you have to remove the outer tie to access the inner tie rod. When you do this, count the rotations of the tie rod as this will have to be replaced when the new inner tie rod is installed. Counting the rotations will allow you to put the outer tie rod close to where it was when you started the job. You are changing the toe setting when you have to replace either the inner or outer tie rod. You need to access and remove the jamb nut and boot before you can access the inner tie rod and this is why the outer needs to be removed first. A wheel alignment is advised after you finish the job. Good luck with this.

May 28, 2011 | Ford Ranger Cars & Trucks

1 Answer

Impact bent the right front tie rod. how can it be removed for straightening or replacing?


First loosen the jam nut with a 21mm wrench. Then use vise grips or whatever you have to make sure the rod can be turned that goes into the outer tie rod. Then remove the cotter pin and 17mm castle nut. Strike the hub where the tie rod goes through with a hammer repeatedly until the tie rod pops out of the hole.

Then simply unscrew the tie rod end and replace it. If the inner tie rod end is also damaged, or the rod is damaged you will need to replace them as well. Inner tie rods have a special tool to remove them, see your local auto parts store.

Remember, replacing an outer tie rod end changes your cars toe (alignment). You will require an alignment after replacing it, even if you think the car drives straight.

Good luck!

Nov 30, 2009 | 2002 Hyundai Accent

2 Answers

Am changing the inner tie rod on a 2000 cirrus with a 2.5 and cant figure out how to get old one off


to get the inner tie rod out you need an inner tie rod tool, it's a long tube that fits a 1/2 inch drive rachet and there's different size adaptors that go into the end of it to fit over the tie rod, find the right size put into tool, put over tie rod and brake it loose, reverse for installtion.

Nov 18, 2009 | 2000 Chrysler Cirrus

1 Answer

How too change inner tierod on 2005 pontiac g6


If you have electric steering(no power steering pump)you have to change the entire steering gear assembly as no part is available.If you have the system with a pump a part is available.In order to change the inner tie rod you would loosen the 21mm lock nut on the tie rod.remove the 18mm nut on the outer tie rod and spin off after removing the outer tie rod from the steering knuckle.Remove the nut and the inner and outer clamps on the tie rod boot.remove the boot.You would then need a special inner tie rod tool to turn the threaded inner rod from the steering gear.

Oct 17, 2009 | 2005 Pontiac G6

2 Answers

Need a diagram on how to change tie rods


you have to apply pressure to get them off,,,all they do is screw in place

Jan 11, 2009 | 1999 Ford Windstar

Not finding what you are looking for?
1999 Chrysler 300M Logo

Related Topics:

154 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...