Question about 2002 Ford SVT Focus

1 Answer

Timeing marks on daul cam for 2002 frod focus 2.0

Did not see no timeing on cam

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,669 Answers

You have to remove the valve cover and insert a flat bar in the slots in the rear of the cams.

Posted on May 31, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I followed your video step by step setting the timing chain with no marks for the 2002 2.0ltr ford focus it still wont start


ok did you follow the ignition timing and firing order set up correctly
did you turn either the crank or cam shaft/s with out the chain
did you do a compression test to check for bent valves

Oct 25, 2016 | 2002 Ford Focus

1 Answer

Is there a ford focus timing marks single overhead cam diagram


depending on trans and engine mount type the mark my be on flywheel but generally most cars it is located on the belt pulley attached to crank rod, center bottom one on engine block. the timeing mark should be visable from top looking down. if you use a big ratchet to turn over the engine by hand and go slowly, you should see thhe marks pass as you do so.

Aug 14, 2014 | 2002 Ford SVT Focus

1 Answer

How to set timing marks on 2000 saturn LS2


need to know what engine size and single or daul cam?

Mar 12, 2011 | 2000 Saturn Ls 4dr Sedan

1 Answer

Timing marks for a 2001 ford focus 2 litre engine where are they and what does it look like


there is no marks!you need special knowledge and tools to timing a zetec engine.try a haynes service manual but is difficult!the cam pulleys sitting on cam shafts with conical joint!without any safe pin or tooth etc.the timing needs to lock the cam shafts and the crankshaft with two special ford tools!try to go on a good garage!!isnt so expensive.a ruined engine is the most expensive repair!

Aug 14, 2010 | 2001 Ford Focus

1 Answer

Need to install a timing belt on a 2002 ford focus with a 2 liter zetec engine cant find the timing marks


No marks to align camshafts, set crankshaft at TDC, align camshaft as shown, to align, lobs on cylinder #1 have to be pointing out at 45 deg, on the other end of camshaft's will be a slot on each one insert some thing through both as shown, to hold camshaft's in place.

0cca4f8.gifcb7ba5c.gif

Aug 05, 2010 | 2002 Ford SVT Focus

2 Answers

Diagram for timming belt on 2002 ford focus 2.0ltr


there isnt marks!the cam pulleys have do nothing with timing!remove the valve cover and see in the other end of the camshafts and find two eccentric cuts!turn the crankshaft to the top dead point on the cylinder 1 the two cuts must be in the same line on the upper or lower side.you need aspecial tool to lock the camshafts and another to lock the crankshaft!this is the timing procedure!now you can change anything you want!note!the cam pulleys are conejointed to the camshafts!no marks no pins no safe pins etc.isnt difficult but complicated simple!

Jan 23, 2010 | 2002 Ford SVT Focus

1 Answer

Focus timing belt replacement.


This is a very very easy timing belt setup. first off you have to remove the valve cover. Then you have to remove the serp belt. Then remove anything thats in your way of the front cover. after you remove the crank pulley re-install the crank bolt. DO NOT LOSEN THE BOLT FOR THE TENSIONER!!!! now spin the crankshaft until the sproket aligns with the timing mark. now at this point the two camshafts should be aligned. now there is a special tool from ford that holds the cam shafts in place. all it is is a 1/4" peice of metal that goes on the left side of the cam shafts to hold them into place. if you mark the cams you wont need the tool. or if you can find something to fit in the left side of the cams that will work too. anyways after that its just the same steps in reverse. very easy to do.

Aug 29, 2009 | 2002 Ford SVT Focus

1 Answer

Cannt find tims marks on 2000 ford focus twin cam


there are no marks on the cams line the crank up you should see marks on it and on the cams take a flat piece of steel like a flat file and put it on the end of the cam shafts the side near near the drivers side ounce you take a look youll see what i mean this should help you out

May 10, 2009 | 2000 Ford Focus

1 Answer

Timing Belt Markings


Mark are on the crank and cam timing gears. Cam gear mark at 12 o"clock crank gear mark lined up with TGC mark on block when installing timing belt.

Dec 16, 2008 | Hyundai Motor 2002 Elantra

5 Answers

2000 ford focus twin cam timing


please helpme i need timing marks for ford focus 2000 16 valvs

Sep 11, 2008 | 2000 Ford Focus

Not finding what you are looking for?
2002 Ford SVT Focus Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...